2010 SKODA FABIA open bonnet

Quick Reference Guide
13
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Slow wipe Fast wipe one time wipe Automatic wipe/wash Rear window wiper Intermittent wipe - every 6 seconds Automatic wipe/washFurther information
page 55, “Windshield wiper”.
Power windows* Button for the power window in the driver's door Button for the power window in the front passenger's door Button for the power window in the rear door on the right* Button for the power window in the rear door on the left* Safety pushbutton*Further information
page 44, “Buttons for elec
trical power windows”.
RefuellingFig. 11 Right rear side of the vehicle: Fuel
filler flap / fuel filler flap with cap unscrewed
– Open the fuel filler flap with the hand
fig. 11
- left.
– Unlock the fuel filler cap on the fuel fi
ller tube to the left using the vehicle key.
– Unscrew the fuel filler ca
p anti-clockwise and place the fuel filler cap from above
on the fuel filler flap
fig. 11
- right.
Further information
page 163, “Refuelling”.
Bonnet remote release– Pull the unlocking lever below the
dash panel on the driver's side
fig. 12
.
Further information
page 165, “Bonnet remote release”.
A2A3A4A5A6A7
Fig. 10 Buttons on the driver's door
AAABACADAS
Fig. 12 Bonnet release lever
s3j8.a.book Page 13 Tuesday, April 20, 2010 1:10 PM

Quick Reference Guide
14Opening the bonnetFig. 13 Radiator grille: Locking lever / se
curing the bonnet with the bonnet support
– Pull on the locking lever
fig. 13
- left, the bonnet is then unlocked.
– Take the bonnet support out of its holder and set it in the opening designed for it
 fig. 13
- right.
Further information
page 165, “Opening and closing the bonnet.”.
Inspecting the engine oil level Engine oil
must not
be refilled.
Engine oil
can
be refilled.
Engine oil
must
be refilled.
Further information
page 167, “Check engine oil level”.
Fig. 14 Dipstick
AaAbAcs3j8.a.book Page 14 Tuesday, April 20, 2010 1:10 PM

Instruments and warning lights
23
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Main menu– You can activate the
MAIN MENU
by pressing the rocker switch
fig. 21
for
more than 1 second.
– You can select individual menu points by means of the rocker switch . When the
pushbutton is briefly pressed, the info
rmation you have sele
cted is displayed.
You can select the following information (d
epending on the equipment installed on
the vehicle):
MFD (Onboard computer)
page 19

Audio
*

Navigation
*

Phone
* page 105

Vehicle status
page 23

Setup
page 24
The menu point
Audio
is only then displayed when
the factory-fitted Radio* is
switched on. The menu point
Navigation
is only then displayed when the factory-fitted Navigation
system* is switched on.
Note

If warning messages are shown in the information display
page 23, these
messages can be confirmed with the button on the windshield wiper lever in order to call up the main menu.
If you do not activate the information disp
lay at that moment, the menu shifts to
one level higher every 10 seconds.
The operation of the factory-fitted radio*
or the navigation system* is described in
separate operating instructions to be
found in the on-board literature.
Door, luggage compartment door and bonnet ajar warningThe door, luggage compartment and bonnet ajar
warning lights up if at least one door,
the luggage compartment or bonnet are not closed. The symbol indicates which door is still open or whether the luggage
compartment door or bonnet is
not closed
.
The symbol goes out as soon as the doors,
luggage compartment door and bonnet are
completely closed. A warning signal sounds if the car is driven at a speed of more than 6km/hour and if the engine or the luggage compartment door is open.Auto Check ControlCar stateThe Auto Check Control carries out a chec
k of certain functions and vehicle compo-
nents. The check is performed constantly when
the ignition is switched on, both when
the vehicle is stationary, as well as when driving. Some operational faults, urgent repairs, se
rvice work or other information appear in
the display of the instrument cluster. The di
splays are shown with a red or yellow light
symbol depending on the priority of the message. The red symbols indicate
danger
(priority 1) while the yellow symbols indicate a
warning
(priortity 2). Information for the driver
may also appear in addition to the
symbols
page 26.
Fig. 21 Information display: Control elements
AAAA
AB
AB
s3j8.a.book Page 23 Tuesday, April 20, 2010 1:10 PM

Instruments and warning lights
303 peeps sound as an additional warning signal. Do not continue your journey
if for some reason it is
not possible under the condi-
tions prevailing to top up with oil.
Keep the engine switched off
and obtain profes-
sional assistance from a specialist garage, otherwise it could lead to severe engine damage. Do not drive any further
if the warning light flashes even if the oil is at the correct
level. Do not run the engine
not at idling speed either. Contact the nearest specialist
garage to obtain professional assistance. The following text will be displayed in the information display*:
Oil Pressure: Engine off! Owner's manual!
The warning light

lights up yellow* (oil quantity too low)
If the warning light lights up yellow, the quantity of oil in the engine is probably too low. Check as soon as possible the oil level or top up
page 167 with engine oil.
A peep sounds as an additional warning signal.The following text will be displayed in the information display*:
Check oil level!
The warning light will go out if the bonnet is le
ft open for more than 30 seconds. If no
engine oil has been replenished, the warning light will come on again after driving about 100 km. The warning light

flashes yellow* (engine oil level sensor faulty)
A fault on the engine oil level sensor is indicated additionally by an audible signal and the warning light coming on several times after the ignition has been switched on. In this case have the engine inspected without delay by a specialist garage.The following text will be displayed in the information display*:
Oil sensor. Workshop!
WARNING

If you must stop for technical reasons, then park the vehicle at a safe
distance from the traffic and switch off the engine and switch on the hazard warning light system
page 51.

The red oil pressure light

is not an oil level indicator! One should there-
fore check the oil level at regular interval
s, preferably after every refueling stop.

Pay attention to the following instructions
page 166, “Working in the
engine compartment” before checking
the coolant fluid level and opening the
bonnet.Open door

The warning light
 comes on if one or several doors are opened or if the boot lid is
opened. If one of the doors opens whil
e driving, the warning light lights
 up and an
audible signal sounds. The warning light comes on even when the ignition is switched off. The warning light lights up for a maximum of 5 minutes. On vehicles with information display* this wa
rning light is replaced by a vehicle symbol
 page 23.Windshield washer fluid level*

The warning light
 comes on when the ignition is swit
ched on if there is insufficient
fluid in the windshield washer system. Top up with liquid
page 176.
The following text will be displayed in the information display*:
To p u p w a s h f l u i d !
Control system for exhaust

The warning light
 comes on after the ignition has been switched on.
If the warning light does not go out after starti
ng the engine or it li
ghts up when driving,
a fault exists in an exhaust relevant co
mponent. The engine management system
selects an emergency programme which enables you to drive to the nearest specialist garage by adopting a ge
ntle style of driving.
WARNING (continued)
s3j8.a.book Page 30 Tuesday, April 20, 2010 1:10 PM

Instruments and warning lights
32
Note
If the battery has been disconnected
and reconnected, the warning light
 comes on
after switching on the ignition. The warning light must go out after driving a short distance.Antilock brake system (ABS)

The warning light
 shows the functionality of the ABS.
The warning light comes on for a few seconds after the ignition has been switched on or when starting the engine. The warning light goes out after an automatic check sequence has been completed. A fault in the ABS The system is not functioning properly if the ABS warning light
 does not go out
within a few seconds after switching on the ignition, does not light up at all or lights up while driving. The vehicle will only be br
aked by the normal brake system. Visit a
specialist garage immediately and adjust your
style of driving appropriately as you will
not know how grea
t the damage is.
Further information about ABS
page 140, “Antilock brake system (ABS)”.
A fault in the entire brake system If the ABS warning light
 comes on together with the brake system warning light

(handbrake must be released), there is a fa
ult not only in the ABS but also in another
part of the brake system

.
WARNING

If the brake system warning light
 comes on together with the ABS
warning light
 stop the vehicle immediately and check the brake fluid level in
the reservoir
page 171, “Brake fluid”. If the fluid level has dropped below the
MIN marking, do not drive any further - risk of accident! Obtain professional assistance.
Pay attention to the following instruct
ions before checking the brake fluid
level and opening the bonnet
page 166, “Working in the engine compart-
ment”.

If the brake fluid is at the correct leve
l, the ABS control function has failed.
The rear wheels may then block very rapi
dly when braking. In certain circum-
stances, this can result in the rear end of the car breaking away - risk of skid-ding! Drive carefully to the nearest sp
ecialist garage and have the fault
rectified.Brake system

The warning light
 flashes or comes on if the brake fluid level is too low, if there is a
fault in the ABS or if
the handbrake is applied.
If the warning light
 flashes and an audible signal so
unds three times (handbrake is
not applied),
stop
and check the brake fluid level

.
The following text will be displayed in the information display*:
Brake fluid: Owner's manual
If there is a fault in the ABS which also infl
uences the function of the brake system (e.g.
distribution of brake pressure), the ABS warning light
 comes on and at the same
time the brake system warning light starts flashing
. Be aware that not only the ABS
but also another part of th brake system is defective

.
An audible signal sounds three times as an additional warning signal.One should get used to high pedal forces, an extended free play of the brake pedal and long braking distances when carefully driving to the specialist garage. For further information on the brake system
page 139, “Brakes”.
Handbrake applied The warning light
 also comes on if the handbrake is applied. An audible warning is
also given if you drive the vehicle for at least 3 seconds at a speed of more than 6 km/h. The following text will be displayed in the information display*:
Release parking brake!WARNING (continued)
s3j8.a.book Page 32 Tuesday, April 20, 2010 1:10 PM

Instruments and warning lights
33
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING

Pay attention to the following instruct
ions before checking the brake fluid
level and opening the bonnet
page 166, “Working in the engine compart-
ment”.
If the brake system warning light
 does not go out a few seconds after
switching on the ignition or comes on when driving, stop immediately and check the brake fluid in the reservoir
page 171, “Brake fluid”. If the fluid level
has dropped below the MIN marking, do no
t drive any further - risk of accident!
Obtain professional assistance.Cruise control system*

The warning light
 lights up, when operating the speed regulating system.
Airbag system

Monitoring the airbag system The warning light
 comes on for a few seconds when the ignition is switched on.
There is a fault in the system if the warning
light does not go out or comes on or flashes
while driving

. This also applies if the warning
light does not come on after the
ignition is switched on. The following text will be displayed in the information display*:
Airbag fault!
The functionality of the airbag system is also monitored electronically when one airbag has been switched off. The following situation applies if the fr
ont, side and head airbags or belt
tensioner have been switched off
using the vehicle system tester:

The warning light
 lights up for 3 seconds after switching on the ignition and then
flashes for 12 seconds afterwards in 2 second intervals. The following text will be displayed in the information display*:
Airbag/belt tensioner deactivated!
If the passenger front airbag has been
switched off using the switch (for
switching off airbags)* in the end face of
the dash panel on the front passenger
side:
The warning light
 comes on for 4 seconds after the ignition has been switched
on.
switching off the airbag is indicated in the middle of the dash panel by the lighting
up of the yellow indicator light in display

 
  page 129.
WARNING
Have the airbag system checked immediat
ely by a specialist
garage if a fault
exists. Otherwise, there is a
risk of the airbag not bein
g activated in the event of
an accident.
Note
Further information about switching off airbags
page 128, “Deactivating airbags”.
Diesel particle filter*

(diesel engine)
If the warning light

comes on, this means that soot
has accumulated in the diesel
particle filter because of the frequent short distances. In order to clean the diesel particle filter, the vehicle should be driven at an even speed of at least 60 km/h at engine speeds of 1
800 - 2 500 rpm for at least 15 minutes or until
the warning light goes out with the 4th or
5th gear engaged (automatic gearbox: posi-
tion S) when the traffic situation permits it. This increases the exhaust temperature and the soot deposited in the diesel particle filter is burnt. Always pay attention to the valid speed limits

.
The warning light

goes out after the successful cleaning of the diesel particle filter.
If the filter is not properly
cleaned, the warning light

does not go out and the
warning light
 begins to flash. In the in
formation display* appears
Diesel-particle
filter! Owner's manual
. Afterwards the engine control unit shifts the engine into the
emergency mode, which only has a reduced po
wer output. After switching the ignition
off and on again the warning light
 comes on.
Have the vehicle inspected without
delay by your specialist garage.
s3j8.a.book Page 33 Tuesday, April 20, 2010 1:10 PM

Unlocking and locking
42The safe securing system along with the anti-theft alarm system* are, however, deac- tivated during these 30 seconds. When the vehicle is unlocked or locked, the interior lights in the door contact are auto- matically switched on or off. Display of the locking The turn signal lights flash once to confir
m that the vehicle has been correctly locked.
If the vehicle is locked by pr
essing the button and some doors or the boot lid are
not closed, the turn signal lights flash only after closing.
WARNING
If the vehicle is locked from the outside and the safe securing system is acti-vated, there must not be any person in the vehicle as it is then not possible to open either a door or a window from the inside. The locked doors make it more difficult for rescuers to get into th
e vehicle in an emergency - hazard!
Note

Operate the radio remote control only when
the doors and boot lid are closed and
you have visual contact with the vehicle.
Once in the vehicle, you must not press the lock button
 of the master key before
inserting the key into the ignition lock in
order to avoid the vehicle being inadvertently
locked and the anti-theft alarm system* being switched on. Should this happen, press the unlock button
 of the master key.
Syncronisation of the remote controlIf the vehicle cannot be unlocked by actuatin
g the remote control system then it is
possible that the code in the key and the co
ntrol unit in the vehicle are no longer
synchronised. This can occur when the buttons on the radio-operated key are actuated a number of times outside of the operative
range of the equipment or the battery on
the remote control was replaced. This means it is necessary to
synchronise the code as follows:

press any button on the remote control;

pressing of the button means that the door will unlock with the key within 1
minute.Anti-theft alarm system*DescriptionThe anti-theft alarm system increases the level of protection against people seeking to break into the vehicle. The system triggers audible and visual warning signals if an attempt is made to break into the vehicle. How is the alarm
system activated?
The anti-theft alarm system is activated au
tomatically when the
unlocked vehicle is
locked with the key inserted in the driver's
door or with the remote control key. It is
activated 30 seconds after locking the door. How is the alarm system deactivated? The anti-theft alarm system is deactivated if
the vehicle is unlocked by only using the
radio remote control. The anti-theft alarm system is reactivated if the vehicle is not opened within 30 seconds after transmitting the radio signal. Once you unlock the vehicle by inserting the ke
y into the driver door you then have to
insert the key into the ignition lock and sw
itch the ignition on within 15 seconds after
opening the door in order to deactivate the anti-theft alarm system. The
alarm will be
triggered
if you do
not switch on
the ignition within 15 seconds.
When is the alarm triggered? The following security areas of
the locked vehicle are monitored:

bonnet;

boot lid;

doors;

ignition lock;

vehicle interior*
page 43;

Angle of the vehicle*
page 43;

Decoupling of the attached trailer;
A3
s3j8.a.book Page 42 Tuesday, April 20, 2010 1:10 PM

Automatic gearbox
100
the right. In the positions
D and
S the gear you have already engaged will be addition-
ally displayed on the display. - Parklock The driven wheels are locked me
chanically in this position.
The Parklock must only be engage
d when the vehicle is stationary

.
If you wish to move the selector lever into
or out of this position, you must press the
Shiftlock button in the handle of the select
or lever and at the same time depress the
brake pedal. - Reverse gear Reverse gear must only be engaged when the vehicle is stationary and the engine idling

.
The brake pedal must be depressed and at
the same time the Shiftlock must be
pressed, if you wish to obtain the selector lever positions
R, P or N.
When the ignition is switched on an
d the selector lever is in position
R, the reverse
lights will come on. - Neutral The transmission is in Neutral in this position. The brake pedal must be depressed (if the le
ver is in its position for longer than 2
seconds) in order to move the selector lever out of the position
N into the position
D,
with the ignition switched on, on a vehicle travelling at less than 5 km/hour or on a stationary vehicle. - Position for driving forward When the selector lever is in this position
, the forward gears are shifted up and down
automatically in line with engine lo
ad, vehicle speed and the dynamic shift
programme. You must depress the brake pedal if you wish to move into position
D from
N when the
vehicle is travelling at less th
an 5 km/hour or is stationary

.
In certain circumstances (e.g. when driving
in mountainous regions or when towing a
trailer) it may be beneficial to
select the manual shift programme
page 102 for a
short time in order to adapt the gearbox
ratios manually to the driving situations.
- Position for sporty style of driving Shifting up later into a higher gear makes it
possible to fully exploit the power potential
of the engine. The gearbox also then shifts down at higher engine speeds as in the posi-tion
D.
The gearbox does not shift into the 6th gear in the position
S, because the maximum
speed is reached with the 5th gear
7).
The Shiftlock on the selector lever grip mu
st be pressed when moving the selector
lever out of the position
D into the position
S.
WARNING

Never move the selector lever into position R or P when driving - risk of an
accident!
When the engine is running and the vehi
cle is stationary, it is necessary to
hold the car with the brake pedal in all the positions of the selector lever (except P and N) since the power transmission is never completely interrupted, also not when the engine is idling - the vehicle creeps. 
You must on no account unintentionally operate the throttle (e.g. by hand
from the engine compartment) if a driv
e position is engaged when the car is
stationary. The vehicle would otherwise
immediately start o
ff - also when the
handbrake is firmly applied - risk of an accident!
You must move the selector lever into position P and firmly apply the hand-
brake first before you or any other person opens the bonnet and starts working on the engine when it is running - risk of accident! It is also essential to observe all warnings
page 166, “Working in the engine compartment”.
Selector lever lockAutomatic selector lever lock

With the ignition on, the selector lever is locked when it is in the positions
P and
N. You
must first of all depress the brake pedal in or
der to move the selector lever out of this
position. The warning light
 page 31 lights up in the instrument cluster as a
reminder for the driver when the selector lever is in the positions
P and
N.
APARANAD
7)Not valid for vehicles with automatic gearbox DSG.AS
s3j8.a.book Page 100 Tuesday, April 20, 2010 1:10 PM