2010 SKODA FABIA ignition

Starting-off and Driving
93
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The handbrake warning is acti
vated if you drive at a speed of more than 6 km/h for
more than 3 seconds.
WARNING

Please note that the handbrake must be fully released. A handbrake which
is only partially released can result in the rear brakes overheating which will have a negative effect on the operation of
the brake system - risk of accident! In
addition this can result in premature wear of the rear brake pads.
Never leave children unattended in the vehicle. The children might, for
example, release the handbrake or take
the vehicle out of gear. The vehicle
might then move off - risk of accident!
Caution
After the car has come to a stop, always firs
t of all apply the handbrake firmly before
then additionally engaging a gear (manual gearbox) or moving the selector lever into position
P (automatic gearbox).
Parking aid*The parking aid provides a warning of obstacles behind the vehicle.The audible parking aid determines the di
stance between the rear bumper and an
obstacle located behind the vehicle with the
aid of ultrasound sensors. The sensors are
integrated in the rear bumper.
Range of sensors The clearance warning begins at a distance
of about 160 cm from the obstacle (area
 fig. 97
). The interval between the warning si
gnals becomes shorter as the clearance
is reduced. A continuous tone sounds from
a distance of approx. 30
cm (area ) - danger area.
You should not reverse any further after this signal sounds!
If the vehicle is
equipped with a factory-fitted
towing device*, the border of the danger area starts -
continuous tone - 5 cm further behind th
e vehicle. The vehicle can be extended
through an installed deta
chable towing device.
Activating The parking aid is activated automatically when
reverse gear
is engaged and the igni-
tion is turned on. This
is confirmed by a brief acknowledgement signal.
Deactivating The parking aid is deactivated by disengaging the reverse gear or by switching the igni- tion off.
WARNING

The parking aid is not a substitute for
the driver paying proper attention and
it is always the driver's responsibility
to take care when parking the vehicle or
carrying out similar manoeuvres.
You should therefore satisfy yourself, before reversing, that there is no small
obstacle, such as a rock, thin post, trai
ler drawbar etc., behind your vehicle.
Such an obstacle might not be within the range detected by the sensors.
Under certain circumstances, surfaces of certain objects and types of
clothing cannot reflect the signal of the parking aid. Thus, these objects or people who wear such clothing are not recognised by the sensors of the parking aid.
Note

The parking aid does not operate if you
are towing a trailer (applies to models
which feature a factory-fitted towing device*).
A system fault is indicated if a warning signal sounds for about 5 seconds after
switching the ignition on and engaging reverse gear and there is no obstacle close to
Fig. 97 Parking aid: Range of sensors
AA
AB
s3j8.a.book Page 93 Tuesday, April 20, 2010 1:10 PM

Starting-off and Driving
94your vehicle. It is possible that the audi
ble warning does not function correctly (an
obstacle behind the vehicle ma
y not be detected - take extra care). Have the fault recti-
fied by a specialist workshop.
If the audible warning sounds for 3 seconds after switching the ignition on and
engaging the reverse gear, a fault has occured in the system. It is possible that the audible warning does not function correctl
y (an obstacle behind the vehicle may not
be detected - take extra care). Have the
fault rectified by a specialist workshop.

The sensors must be kept clean and free of ice to enable the parking aid to operate
properly.
If the parking aid is activated and the sele
ctor lever of the automatic gearbox is in
the position , warning signal indicates interruption (vehicle can no longer move).Cruise control system (CCS)*IntroductionThe cruise control system (CCS) maintains
a constant speed, more than 30 km/h (20
mph), once it has been set, without you havi
ng to depress the accelerator pedal. This
is only possible within the range which is permitted by the power output and braking power of the engine. The cruise control system
makes it possible - particularly on long
journeys - for you to rest your “accelerator foot”.
WARNING

For safety reasons, the cruise control system must not be used in dense
traffic or on unfavourable road surfaces
(such as icy roads, slippery roads, loose
gravel) - risk of accident!
In order to prevent unintentional use of the cruise control system, always
switch off the system after use.
Note

Models fitted with a manual gearbox: Always
depress the clutch pedal if you switch
on the cruise control system when the gearbo
x is in Neutral! Otherwise the engine can
rev up unintentionally.

The cruise control system is not able to maintain a constant speed when driving on
steep downhill sections. The weight of the vehicle increases the speed at which it travels. One should shift down in good time
to a lower gear or slow the vehicle down
by applying the foot brake.
It is not possible on vehicles fitted with
an automatic gearbox to switch on the
cruise control system if the sele
ctor lever is in the position
P, N or R.
Storing a speedThe cruise control system is operated by means of the switch and the rocker button in the left lever of the multi-functional switch. – Press the switch
fig. 98
into the position
ON
.
– After the desired speed has been reached, press the rocker button into the
SET-

position - the current speed is stored.
After you have released the rocker button out of the position
SET-
, the speed you
have just stored is maintained at a consta
nt speed without having to depress the accel-
erator. You can
increase
the speed by depressing the acce
lerator. Releasing the accelerator
will cause the speed to
drop
again to the set speed.
This does not apply, however, if you drive at
a speed which is more than 10 km/h higher
than the set speed for a period of longer
than 5 minutes. The stored speed will be
cancelled in the memory. You then have to re-store the desired speed. One can
reduce
the speed in the usual manner. The system is switched off temporarily
by actuating the brake or clutch pedal
page 95.
AP
Fig. 98 Operating lever: Rocker button and switch of the cruise control system
AA
AB
AA
AB
AB
s3j8.a.book Page 94 Tuesday, April 20, 2010 1:10 PM

Starting-off and Driving
95
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
First ensure that it is not too high for the traffic conditions which exist at that moment before resuming the stored speed.Changing a stored speed You can also change the speed of
the vehicle without depressing the
accelerator.Fa s t e r–You can
increase
the stored speed without depressing the accelerator, by pressing
the rocker button
page 94, fig. 98
into the
RES+
position.
– The speed of the car will increase cont
inuously if you hold the rocker button
pressed in the
RES+
position. Once the vehicle ha
s reached the desired speed,
release the rocker button. The set speed is then stored in the memory.
Slower–You can
decrease
the stored speed by pressing the rocker button in the
SET-

position.
– Holding down the pushbutton pressed in the
SET-
position will cause the speed of
the vehicle to reduce continuously. On
ce the vehicle has reached the desired
speed, release the rocker button. The set speed is then stored in the memory.
– If you release the rocker button when the vehicle is travelling at a speed of less than
30 km/h, the speed is not stored, the memory is erased. It is then necessary to again store the speed with the rocker button in the position
SET-
after an increase in
speed of the vehicle to more than 30 km/hour.
Switching off the cruise control system temporarily–You can
switch off
the cruise control system
temporarily
by depressing the brake
pedal or clutch pedal, on vehicles fitted
with an automatic gearbox only with the
brake pedal.
– You can switch off temporarily the cruise control system, if you press the switch
in the middle position.
The set speed remains stored in the memory. The
Resumption
of the stored speed is achieved by releasing the brake or clutch
pedal, on vehicles fitted with automatic
gearbox only after releasing the brake pedal
and after shortly pressing the rocker button
page 94, fig. 98
into the position
RES+
.WARNING
First ensure that it is not too high for the traffic conditions which exist at that moment before resuming the stored speed.Switching off the cruise control system completely– Press the switch
page 94, fig. 98
to the right into position
OFF
.
“START-STOP”*The “START-STOP” system helps you to save
fuel while at the same time reducing
exhaust pollutants and CO
2 emissions.
The system is automatically activated ea
ch time the ignition
is switched on.
The system switches the engine off automa
tically when the vehicle comes to a stand-
still, such as while wa
iting at a traffic light.
Information regarding the current state of the “START-STOP” system is indicated in the display of the instrument cluster.
AB
AB
AB
AA
AB
AA
Fig. 99 Centre console: Button for the START-STOP system
s3j8.a.book Page 95 Tuesday, April 20, 2010 1:10 PM

Starting-off and Driving
97
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Messages in the instrument cluster (valid for vehicles without information display*)
WARNING

If the engine is switched off, neit
her the brake booster nor the electrohy-
draulic power steering operates.
Never let the vehicle roll wi
th the engine switched off.
Caution
If the “START-STOP” system is used at very
high outside temperatures over a longer
period of time, the vehicl
e battery can be damaged.
Note

A change in ambient temperature can affect the temperature inside the battery
with several hours delay. For example, if
the vehicle is standing outside for a long
period of time at a temperature below freezi
ng, or vice versa under
direct sunlight, it
may take several hours until the temperat
ure inside the battery reaches the appro-
priate temperature for the START-STOP system.
In some cases, it is necessary to manually start the engine using the key (for
example, if the driver's seat belt is not fastened or if the driver door is open for a period of more than 30 seconds during the stop
phase). Pay attention to the relevant
messages in the instrument cluster.
If the Climatronic* is switched into the automatic mode, this may in certain circum-
stances prevent the automatic engine shut down.
ERROR START STOP FEHLER START STOP
Error in the START-STOP system
ENGINE MUST RUN MOTORLAUF NOETIG
Automatic engine shut down is not possible
START STOP ACTIVE START STOP AKTIV
Automatic engine shut down (stop phase)
SWITCH OFF IGNITION ZUENDUNG AUSSCHALTEN
Switch off the ignition
START ENGINE MANUALLYMOTOR MANUELL STARTEN
Start the engine manu- ally
s3j8.a.book Page 97 Tuesday, April 20, 2010 1:10 PM

Automatic gearbox
100
the right. In the positions
D and
S the gear you have already engaged will be addition-
ally displayed on the display. - Parklock The driven wheels are locked me
chanically in this position.
The Parklock must only be engage
d when the vehicle is stationary

.
If you wish to move the selector lever into
or out of this position, you must press the
Shiftlock button in the handle of the select
or lever and at the same time depress the
brake pedal. - Reverse gear Reverse gear must only be engaged when the vehicle is stationary and the engine idling

.
The brake pedal must be depressed and at
the same time the Shiftlock must be
pressed, if you wish to obtain the selector lever positions
R, P or N.
When the ignition is switched on an
d the selector lever is in position
R, the reverse
lights will come on. - Neutral The transmission is in Neutral in this position. The brake pedal must be depressed (if the le
ver is in its position for longer than 2
seconds) in order to move the selector lever out of the position
N into the position
D,
with the ignition switched on, on a vehicle travelling at less than 5 km/hour or on a stationary vehicle. - Position for driving forward When the selector lever is in this position
, the forward gears are shifted up and down
automatically in line with engine lo
ad, vehicle speed and the dynamic shift
programme. You must depress the brake pedal if you wish to move into position
D from
N when the
vehicle is travelling at less th
an 5 km/hour or is stationary

.
In certain circumstances (e.g. when driving
in mountainous regions or when towing a
trailer) it may be beneficial to
select the manual shift programme
page 102 for a
short time in order to adapt the gearbox
ratios manually to the driving situations.
- Position for sporty style of driving Shifting up later into a higher gear makes it
possible to fully exploit the power potential
of the engine. The gearbox also then shifts down at higher engine speeds as in the posi-tion
D.
The gearbox does not shift into the 6th gear in the position
S, because the maximum
speed is reached with the 5th gear
7).
The Shiftlock on the selector lever grip mu
st be pressed when moving the selector
lever out of the position
D into the position
S.
WARNING

Never move the selector lever into position R or P when driving - risk of an
accident!
When the engine is running and the vehi
cle is stationary, it is necessary to
hold the car with the brake pedal in all the positions of the selector lever (except P and N) since the power transmission is never completely interrupted, also not when the engine is idling - the vehicle creeps. 
You must on no account unintentionally operate the throttle (e.g. by hand
from the engine compartment) if a driv
e position is engaged when the car is
stationary. The vehicle would otherwise
immediately start o
ff - also when the
handbrake is firmly applied - risk of an accident!
You must move the selector lever into position P and firmly apply the hand-
brake first before you or any other person opens the bonnet and starts working on the engine when it is running - risk of accident! It is also essential to observe all warnings
page 166, “Working in the engine compartment”.
Selector lever lockAutomatic selector lever lock

With the ignition on, the selector lever is locked when it is in the positions
P and
N. You
must first of all depress the brake pedal in or
der to move the selector lever out of this
position. The warning light
 page 31 lights up in the instrument cluster as a
reminder for the driver when the selector lever is in the positions
P and
N.
APARANAD
7)Not valid for vehicles with automatic gearbox DSG.AS
s3j8.a.book Page 100 Tuesday, April 20, 2010 1:10 PM

Automatic gearbox
101
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
A time delay element ensures that the selector lever is not blocked when rapidly switching over the position
N (e.g. from
R to D). This does, for example, allow one to
seesaw out a stuck vehicle. The selector lever lo
ck will click into place if the lever is in
the
N position for more than 2 seconds without the brake pedal being pressed.
The selector lever lock is only active if the
vehicle is stationary or
moving at speed of
less than 5 km/hour. The lock is swit
ched off automatically into position
N when the
car is travelling at a higher speed. Shiftlock button The Shiftlock button in the hand
le of selector lever prevents certain selector lever posi-
tions being engaged inadvertently. The selector lever lock is cancelled when you press the Shiftlock button. Keylock
8)- Ignition key withdrawal lock
You can only withdraw the ignition key after switching off the ignition if the selector lever is in position
P. If the ignition key is withdrawn, the selector lever is blocked in
position
P.
Kickdown function The kickdown function provides you with maximum acceleration power.Fully depressing the accelerator pedal allows
the kickdown function to be activated in
the desired driving program. This function has precedence over the driving programme and serves for maximum acceleration of the vehicle when exploiting the maximum power potential of the engine wi
thout taking into account the current
selector lever position (
D, S or Tiptronic
). The gearbox shifts down to one or several
gears in line with the driving state and the vehicle accelerates. The gearbox does not shift up into the highest gear until the en
gine has reached its maximum revolutions for
this gear range.
WARNING
Please note that using the kickdown function can result in the driven wheels spinning on a smooth or slippery road surface - risk of skidding!
Dynamic shift programmeThe automatic gearbox of your vehicle is
controlled electronically. Shifting up and
down through the gears is performed automatically on the basis of pre-defined driving programmes. Adopting a
moderate style of driving
will cause the gearbox to select the most
economical driving programme. Shifting up into a higher gear as soon as possible and shifting down as late as po
ssible will have a favourable effect on your fuel consump-
tion. Adopting a
sporty style of driving
with rapid movements of the accelerator pedal
combined with sharp acceleration and freque
nt changes in speed, exploiting the top
speed of the car or depressing the accele
rator pedal (kickdown function), will cause
the gearbox to switch over to this style of driving and shift down earlier with frequent changes in gears in comparison to the moderate style of driving. Selecting the most appropriate driving programme for the particular style of driving is a continuous process. Irrespective of this it is, however, possible to switch or shift down into a dynamic shift programme by depressi
ng the accelerator rapidly. The gearbox
shifts down into a lower gear matching the speed of the car and this allows you to accelerate rapidly (e.g. when overtaking)
without having to depress the accelerator
pedal fully into the kickdown range. The or
iginal programme will be reactivated to
match your particular styl
e of driving once the gearbox has shifted up again.
When driving in hilly regions, the gears are selected to match uphill and downhill sections. This avoids the gearbox frequently
shifting up and down when negotiating an
uphill stretch. When driving downhill, it is
possible to shift do
wn into the Tiptronic
position, in order to exploit the engine brake torque.
8)Only valid for some countries.
s3j8.a.book Page 101 Tuesday, April 20, 2010 1:10 PM

Communication
106
To ensure an optimum signal transmission, always leave the telephone with the adapter* in the telephone mount. Furthermore the volume can be changed indivi
dually during the call at any time with
the button for setting the radio* or navigation system* or with the buttons on the multifunction steering wheel*.
WARNING
Pay attention primarily to the traffic situation! As the driver you are fully responsible for road safety. Use the teleph
one system only to such an extent, so
that you are in full control of your vehicle at any time.
Note

Please refer to the following guidelines
page 105.

Should you have any questions, please
contact an authorised Škoda Service
Par tner.Phone PhonebookA phone phonebook is part of the mobile ph
one preinstallation with voice control. In
the phone phonebook there are 2 500 free memory locations available. This phone phonebook can be used in line
with the mobile telephone.
After the first connection of the telephone, the system begins to load the phone book from the phone and the SIM card into the memory of the control unit. Each time the telephone has establishe
d a new connection with the hands-free
system, an update of the relevant phone b
ook is performed. The updating can take a
few minutes. During this time the phone book, which was stored after the last update was completed, is available. Newly stored telephone numbers are only shown after the updating has ended. If the number of contacts loaded exceed
s 2 500, the phone book is not complete.
If a telephone event (e.g. incoming or outgoing call, dialogue of the voice control) occurs during the updating pr
ocedure, the updating is interrupted. After the telephone
event has ended, the updating starts anew.
Connection of the mobile phone with the hands-free systemIn order to connect a mobile phone with th
e hands-free system, it is necessary to
connect the telephone to the hands-free sy
stem. Detailed information on this is
provided in the operating instructions of your mobile phone. The following steps must be carried out for the connection: – Activate the Bluetooth
® in your telephone and the visibility of the mobile phone.
– Switch on the ignition.– Select the menu
Phone
- Phone search
in the information display and wait until
the control unit has ended the search.
– Select your mobile phone in the menu of the units found.–Confirm the PIN (as standard
1234
).
– If the hands-free system
announces (as standard
Skoda UHV
) on the display of the
mobile phone, enter the PIN (as standard
1234
) within 30 seconds and wait until
the connection is established.
10)
– After ending the connection, confirm in the information display that a new user
profile was created.
If no more free space is available for creating a new user profile, delete an existing user profile. If you have not managed to
connect your mobile phone with the hands-free system
within 3 minutes after switching on the ignition, switch the ignition off and then again on. The visibility of the hands-free system is established again for 3 minutes. The visi- bility of the Bluetooth
® device is automatically switched
off if the vehicle starts off or
if the mobile phone connects to the device. During the connecting procedure, no other
mobile phone may be connected with the
hands-free system. Up to four mobile phones ca
n be paired to the hands-fr
ee system, whereby only one
mobile phone can communicate
with the hands-free system.
10)Some mobile phones have a menu, in which the authorization for establishing a Bluetooth
®
connection is performed via the input of a code. If the input for the authorization is necessary, it must always be performed when re-e
stablishing the Bluetooth connection.
s3j8.a.book Page 106 Tuesday, April 20, 2010 1:10 PM

Communication
107
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Connection with an already paired mobile phone After switching on the ignition, the connect
ion is automatically established for the
already paired mobile phone
10). Check on the mobile unit if the automatic connection
was established. Disconnecting the connection
By withdrawing the ignition key.

By disconnecting the device in the information display.

By disconnecting the device in the mobile phone.
Solving connection problems If the system announces
No paired phone found
, check the operating state of the
telephone:
Is the telephone switched on?

Is the PIN code entered?

Is Bluetooth
® active?

Is the visibility of the mobile phone active?

Was the telephone already paired with the hands-free system?
WARNING
In the event of air transport, the Bluetooth
® function of the hands-free system
must be switched off by a specialist garage!
Note

Not valid for all mobile phones which enable a communication via Bluetooth
®.
You can ask at an authorised Škoda Service Partner if your telephone is compatible with the universal telephone preinstallation GSM II.
Please operate your mobile phone exclusiv
ely with a suitable adapter in order to
keep a low radiation in the vehicle.
Inserting the mobile phone into the adapter ensures an optimal sending and
receiving power and offers at the same ti
me the advantage of the battery charging.

The range of the Bluetooth
® connection to the hands-free system is restricted to
the vehicle interior. The range is dependent on local factors, e.g. obstacles between the
devices and mutual interferences with other de
vices. If your mobile phone is e.g. in a
jacket pocket, this can lead to diffic
ulties when establishing the Bluetooth
® connection
with the hands-free system or the data transfer.Inserting the mobile phone with the adapter*Only one telephone mount* is factory-fitted. An adapter for the telephone can be purchased from the range of the Škoda original accessories.Inserting the mobile phone with the adapter– First of all push the adapter in the direction of arrow
fig. 105
up to the stop
into the mount. Press the adapter slightly downwards, until it locks securely into position.
– Insert the mobile phone into the adap
ter (as specified in manufacturer's
instructions).
Removing the mobile phone with the adapter– Press simultaneouly the side locks of the mount and remove the mobile phone and
adapter
fig. 105
.
Caution
Taking the mobile phone out of the adapter du
ring the call can lead to interruption of
the connection. When taking out the mobi
le phone, the connection to the factory-
fitted antenna is interrupted, this reduces the quality of the transmitting and receiving signal. The charging of the mobile
phone battery is also interrupted.
Fig. 105 Universal preparation for the phone
AA
AA
s3j8.a.book Page 107 Tuesday, April 20, 2010 1:10 PM