2010 SKODA FABIA fuel

Fuel
164
WARNING
Pay attention to any legal requirements if you do carry a spare canister in the vehicle. We do not recommend carrying any fuel canisters in your vehicle for safety reasons. The canister can be damaged
in the event of an accident and fuel
may leak out.
Caution

Remove any fuel which has spilled onto th
e paintwork of your vehicle immediately
- risk of paint damage!
On vehicles fitted with a catalytic converte
r, never let the fuel tank run completely
empty. An irregular supply of fuel to the engine can result in misfiring and unburnt fuel may get into the exhaust system, which may
result in overheating and damage to the
catalytic converter.
Make sure that the valve is not pressed into the filler tube when inserting the pump
nozzle into the filler tube.
Otherwise you are unintentiona
lly filling up the volume,
which in case of heat can caus
e an expansion of the fuel. This can lead to an overflow
of fuel or damage to parts of the fuel reservoir.
The fuel tank is full just as soon as th
e pump nozzle switches off for the first time,
provided the nozzle has been operated prop
erly. Do not continue refuelling - other-
wise the expansion volume is filled up.
Note
The fuel tank has a
capacity of about
45 litres
, containing a reserve of
7litres
.
s3j8.a.book Page 164 Tuesday, April 20, 2010 1:10 PM

Inspecting and replenishing
168
It is normal for the engine to consume oil.
The oil consumption may be as much as 0.5
l/1 000 km depending on your style of driving and the conditions under which you operate your vehicle. The oil
consumption may be slightly hi
gher than this during the
first 5 000 kilometres. One should therefore check the oil level at regular intervals, preferably every time after the fuel tank is filled or after driving for long stretches. We recommend maintaining the oil level within the range if the engine has been operating at high loads, for example duri
ng a lengthy motorway trip during the
summer months, towing a trailer or
negotiating a high mountain pass,
but not above
this
.
The warning light in the instrument cluster* will indicate
page 29 whether the oil
level is too low. In this case, check the oil
level as soon as possible. Top up with an
appropriate quantity of oil.
WARNING
Read and observe the warning notes
page 166, “Working in the engine
compartment” before working in the engine compartment.
Caution

Always check the oil level on vehicles with engine 1.2 ltr./44 kW when the engine is
cold, on other vehicles when the engine is warm. Otherwise the measuring result is incorrect und oil could be incorrectly
replenished - risk of engine damage!

The oil level must on no account extend
beyond the range . Danger of damaging
the catalytic converter.
Do not continue your journey
if for some reason it is not possible under the
conditions prevailing to top up with oil.
Switch the engine off
and obtain professional
assistance from a specialist garage, otherwise it could lead to severe engine damage.Replenishing engine oil– Inspect the oil level
page 167.
– Unscrew the cap of the engine oil filler opening.
– Wipe off the oil from the sealing surface of the cover and on the counterpart using
a clean cloth.
– Pour in a suitable grade of oi
l in portions of 0.5 litres
page 210.
– Inspect the oil level
page 167.
– Carefully screw on the cap of the filler opening and push the dipstick in fully.
WARNING

Avoid dripping oil onto hot parts of the engine when topping up will oil - a
risk of fire!
Read and observe the warning notes
page 166, “Working in the engine
compartment” before working in the engine compartment.
For the sake of the environment
The oil level must on no account be above the range
page 167. Oil will otherwise
be drawn in through the cr
ankcase ventilation and may
pass through the exhaust
system to atmosphere. The oil may combust
in the catalytic conv
erter and damage it.
Changing engine oilThe engine oil must be changed at the intervals stated in the Service schedule or according to the service interval indicator
page 17.
WARNING

Only carry out the engine oil change, if you have the required professional
knowledge!
Read and observe the warning notes
page 166, “Working in the engine
compartment” before working in the engine compartment.
First of all, let the engine cool down, we
ar an eye protection and gloves - risk
of caustic burns due to hot oil.
AaAa
Aa
s3j8.a.book Page 168 Tuesday, April 20, 2010 1:10 PM

Wheels and Tyres
178
Wheels and TyresWheelsGeneral information
New tyres do not offer optimal grip at first and should therefore be run in for about
500 km at a moderate speed and an appropri
ately cautious style of driving. You will
also profit from longer tyre life.
The tread depth of new tyres may differ be
cause of design features and the config-
uration of the tread (depending on the type of tyre and the manufacturer).
Drive over curbs on the side of the road
and other such obstacles slowly and,
where possible, at a right angle in order
to avoid damage to tyres and wheel trims.

Inspect your tyres from time to time
for damage (punctures, cuts, splits and
bulges). Remove foreign bodies from the tyre profile.
Damage to tyres and wheels is frequently
not visible. Unusual vi
brations or pulling
of the vehicle to one side coul
d be a sign of tyre damage.
Please reduce your speed
immediately and stop if you su
spect that a wheel is damaged.
Inspect the tyres for
signs of damage (bulges, splits, etc.). If no
visible damage is present, please drive at an
appropriately slow speed and carefully to the nearest specialist garage in order to have your vehicle inspected.
Also protect your tyres from contact with oil, grease and fuel.

Immediately replace any dust caps of
the valves which have got lost.

Mark wheels before removing them so that
their previous dire
ction of running can
be maintained when mounted them again.
Always store wheels or tyres which been removed in a cool, dry and, where
possible, dark place. Tyres which are not fixed to a wheel trim should be stored upright. Unidirectional tyres* The direction of rotation of the tyres is mark
ed by arrows on the
wall of the tyre. This
indicates the direction of rotation of the tyre, and it is essential that the tyres are fitted on to run in this direction. Only then are
the tyres able to provide the optimal proper-
ties in terms of grip, low nois
e, wear-and-tear and aquaplaning.
Further information concerning th
e use of unidirectional tyres
page 182.
WARNING

New tyres during the first 500 km do not offer optimal grip and should
therefore be run appropriately - risk of accident!
Never drive with damaged tyres - risk of accident!Note
Please observe the various differing legal requirements regarding tyres.Ty re l i feThe life of your tyres very much depends on the following points: Tyre pressure The working life of tyres will be shortened considerably if the tyres are insufficiently or over-inflated and this will have an adverse
effect on the handli
ng of your vehicle.
Correctly inflated tyres are of particular importance when travelling at
high speeds
. It
is therefore good to check the pressure at
least once a month and also before setting
off on a long trip. Please do not forget the spare wheel* when checking the tyres. The tyre inflation pressures for
summer tyres
are indicated on the inside of the fuel
filler flap
fig. 147
. The inflation pressures for
winter tyres
are 20 kPa (0.2 bar) higher
than those for summer tyres
page 182.
Fig. 147 An opened fuel filler flap with a tyre size and tyre inflation pressure table
s3j8.a.book Page 178 Tuesday, April 20, 2010 1:10 PM

Wheels and Tyres
179
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The tyre pressure should be
at the highest pressure specified for your vehicle at all
times. Always check the inflation pressure of tyres
when cold. Do not reduce the higher pres-
sure of warm tyres. Adapt the inflation pressure of the tyres accordingly if your vehicle is carrying a significantly higher payload. Tyre inflation pressure - Tyre size 185/55 R15 The same inflation pressure values apply to ty
res of the tyre size 195/55 R15 as to tyres
of the tyre size 185/55 R15 which are intended to be used with snow chains, see the inside of the fuel filler flap. The tyres of the tyre size 185/55 R15, which are intended to be used with snow chains and are fitted on models Fabia Combi Scout, have the following inflation pressure values in kPa. Driving style Fast cornering, sharp acceleration and brak
ing (squealing tyres) increase wear-and-
tear on your tyres. Balancing wheels The wheels of a new vehicle are balanced. There are a wide range of influences when driving which may result in an imbalance
and which makes themselves felt through
vibration in the steering.
You should have the wheels rebalanced si
nce any imbalance increases wear-and-tear
on the steering, the suspension and tyres. A wheel must also be rebalanced when a new tyre is fitted and each time a tyre is repaired. Wheel alignment errors Incorrect wheel alignment at the front and rear
will not only increase wear-and-tear on
the tyres but will also has an adverse effect on vehicle safety. Contact your specialist garage if you notice any unusual tyre wear.
WARNING

If the inflation pressure is too low,
the tyre must perform a higher rolling
resistance. At higher speeds the tyre will warm up as a result of this. This can result in tread separation and even a tyre blowout.
Immediately replace the damaged rims or tyres.

Tyres which are 6 years old or more should only be fitted in exceptional
cases and when adopting an approp
riately cautious style of driving.
For the sake of the environment
Tyres which are insufficiently inflated increase your fuel consumption.Wear indicatorsThe base of the tread of the original tyres has wear indicators 1.6 mm high, installed at right angles to the direction of travel. These
wear indicators are lo
cated at 6 - 8 points
depending on the make and are evenly spaced around the circumference of the tyre
Engine
Partial load
Full load
1.2/63 kW TSI
220/230
220/230
1,4/63 kW
220/290
1.2/77 kW TSI
230/300
1.6/77 kW
230/300
1,2/55 kW TDI CR
230/300
1.6/66 kW TDI CR
220/290
1.6/77 kW TDI CR
220/290
Fig. 148 Tyre tread with wear indicators
s3j8.a.book Page 179 Tuesday, April 20, 2010 1:10 PM

Wheels and Tyres
182
Winter tyresThe handling of your vehicl
e will be significantly improved when driving on wintry
roads if you fit winter tyres. Summer tyres do not offer the same grip on ice, snow and at temperatures below 7 °C because of thei
r construction (width, rubber blend, tread
pattern). This applies in particular
to vehicles which are equipped with
low-profile
tyres
or high-speed tyres
(code index H, V or W on wall of tyre).
Winter tyres must be mounted on all four
wheels to obtain the best handling charac-
teristics. You must only fit those types of winter tyre
which are approved for your vehicle. The
permissible
sizes of winter tyres
are stated in your vehicl
e documents. Approvals may
differ because of na
tional legislation.
Please remember that the tyres should be inflated to 20 kPa (0.2 bar) more than is the case for summer tyres
page 178.
Winter tyres no longer offer the
same winter performance once the
tyre tread
has
worn down to a depth of about 4 mm. Ageing
also causes winter tyres to lose most of their winter performance properties -
even in cases where the remaining tread depth is still clearly more than 4 mm. Speed restrictions
apply to winter tyres as well as to summer tyres
page 180,

.
You can fit winter tyres of a lower speed catego
ry to your vehicle provided that you also
do not drive faster than the permissible maximum speed for such tyres, even if the possible maximum speed of your vehicle is
higher. The correspond
ing tyre category
can damage the tyres when exceeding the permissible maximum speed. Please pay attention to the notes if
you decide to fit winter tyres
page 178.
You can also fit so-called “all-year tyres” instead of winter tyres. Please contact your specialist garage if there are any points which are not clear who will be able to provide you with information regarding the maximum speed for your tyres.
WARNING
You must on no account drive your car at more than the permissible maximum speed for your winter tyres - risk of an
accident resulting from tyre damage and
loss of control over your car.
For the sake of the environment
Fit your summer tyres on again in good time since summer tyres offer you better grip and handling on roads which are free of snow
and ice as well as ar temperatures below
7 °C - the braking distance is shorter, there is less tyre noise, tyre wear is reduced and fuel consumption is reduced.
Note
Please observe the various differing legal requirements regarding tyres.Unidirectional tyres*The direction of rotation of the tyres is marked by
arrows on the wall of the tyre
. This
indicates the direction of rotation of the tyre,
and it is essential that the tyres are fitted
on to run in this direction. Only then are the tyres able to provide the optimal proper- ties in terms of grip, low nois
e, wear-and-tear and aquaplaning.
Should it be necessary to fit on a spare wheel* in the event of a puncture with a tyre not dedicated to the running dire
ction or in opposite runnin
g direction, please adopt a
cautious style of driving as the tyre is no
longer able to provide optimal grip and
handling in such a situation. This particular
ly important on wet roads. Please refer to
the additional instructions
page 186, “Spare wheel*”.
You should have the defective tyre replaced as soon as possible and restore the correct direction of rotation on all tyres.Snow chainsSnow chains must only be mounted on the front wheels. When driving on wintry roads, snow chains
improve not only traction, but also the
braking performance. For technical reasons, it is only permissi
ble to fit snow chains
with the following
wheel/tyre combinations.
s3j8.a.book Page 182 Tuesday, April 20, 2010 1:10 PM

Breakdown assistance
186
The vehicle tool kit and the lifting jack* are
housed in a plastic box in the spare wheel*
 page 185, fig. 150
or in the space for the spare wheel. There is also space here for
the removable ball for the trailer towing device. The vehicle tool kit contains the following
parts (depending on equipment fitted):

wheel wrench*;

wire clamps for removing the full wheel trims;

towing eye;

Adapter for the safety wheel bolts*;

Extraction pliers for wheel bolt caps;

Replacement bulb set;

Screwdriver*.
Before placing the lifting jack back in its storage area, screw in the arm of the lifting jack fully.
WARNING

The factory-supplied lifting jack is only intended for your model of vehicle.
On no account attempt to lift a heavier vehicle or other loads - risk of injury!
Ensure that the vehicle tool kit is safely attached in the luggage
compartment.Tyre repair kitThe tyre repair kit is intended for the repair
of minor tyre defects. The tyre repair kit
contains a compressor, inflation bottle,
operating instructions and accessories.
The repair with the tyre repair kit is
not at all intended to replace
a permanent repair
on the tyre; this repair only serves to re
ach a workshop. The repair can be undertaken
on the vehicle immediately.
Please read the attached in
structions carefully before
the repair. The ty re re pa ir kit i s s towed in a n ins er ted foa m pie ce unde r the lugga ge com pa r tment cover or in the right part
of the luggage compartment.
Spare wheel*The spare wheel is stowed in th
e spare wheel well in the luggage
compartment below the floor covering.The spare wheel lies in a well under the floor covering of the luggage compartment and is fixed in place along with a vehicle tool kit box using a special screw
fig. 151
.
One should check the inflation pressure in
the spare wheel (at best when generally
checking the tyre air pressures - see sign on the fuel filler flap
page 163) to ensure
that the spare wheel is always ready to use. Unidirectional tyres* If you have such tyres on your vehi
cle, please refer to the notes below:

The spare wheel provided with a car fitted with unidirectional tyres has different
dimensions. The wheel is provided with a warning sticker.
The warning label must not be covered after installing the wheel.

Do not drive faster than 80 km/h with this spare wheel and pay particular attention
while driving. Avoid accelerating at full throttle, sharp braking and fast cornering.
The inflation pressure for this spare wheel is identical to the inflation pressure of
the standard tyres.
Use this spare wheel only to reach the nearest specialist garage as it is not intended
for continuous use.
Fig. 151 Luggage compartment: Spare wheel
s3j8.a.book Page 186 Tuesday, April 20, 2010 1:10 PM

Breakdown assistance
192
WARNING

The non-insulated parts of the terminal clamps must never make contact
with each other. Furthermore, the cable connected to the positive terminal of the battery must not come into contact with electrically conducting parts of the vehicle - risk of a short circuit!
Do not affix the jump starting cables to the negative terminal of the
discharged battery. There is
the risk of detonating gas seeping out the battery
being ignited by the strong spark which
results from the engine being started.

Do not affix the cable end to parts of the fuel and brake system.

Run the jump-start cables so that they cannot be caught by any rotating
parts in the engine compartment.
Do not bend over the batteries - risk of caustic burns!

The vent screws of the battery
cells must be tightened firmly.

Keep any sources of ignition (naked
flame, smouldering
cigarettes etc.)
away from the battery - risk of an explosion!
Never jump-start the batteries which have a too low electrolyte level - risk
of explosion and caustic burns!Jump-starting on vehicles with the “START-STOP” systemOn vehicles with the “START-STOP” syst
em, the jump-starting cable must not be
connected directly to the negative terminal
of the vehicle battery, but only to the
engine earth
fig. 158
.
Tow-starting and towing vehicleGeneralPlease pay attention to the following instru
ctions if you are going to use a tow rope:
Driver of the towing vehicle– Do not drive off until the tow rope is taught. – Release the clutch particularly gently when starting off.Driver of the towed vehicle– Switch the ignition on so that the steeri
ng wheel is not blocked and you can also
operate the turn signal lights, the headlight flasher, the windscreen wipers and windscreen washer system.
– Take the vehicle out of gear or move the selector lever into position
N if your
vehicle is fitted with an automatic gearbox.
– Note that the brake servo unit and power steering only operate if the engine is
running. You will require significantly greater physical force to depress the brake pedal and to steer the vehicle
if the engine is not running.
– Ensure that the tow rope is always kept taught. Tow rope or tow bar A tow
bar
is safest way of towing a vehicle and also minimizes any shocks. You can use
a tow
rope
only if a suitable tow bar is not available.
The tow rope must be elastic to protect the
vehicle. Thus one shou
ld only use plastic
fibre rope or a rope made out
of a similarly elastic material.
Attach the tow rope or the tow bar only to the
towing eyes
provided for this purpose
 page 193, “Front towing eye” and
page 193, “Rear towing eye”.
Driving style Towing another vehicle requires a certain am
ount of practice. Both drivers should be
familiar with the particular points about to
wing a vehicle. Unskilled drivers should not
attempt to tow in another vehicle or to be towed in.
A4
Fig. 158 Jump-starting - START-STOP system
s3j8.a.book Page 192 Tuesday, April 20, 2010 1:10 PM

Fuses and light bulbs
196
Fuse assignment in the dash panelFig. 162 Schematic representation of the fuse
box for vehicles with left-hand steering / right-
hand steeringCertain electrical components are only standard on certain vehicle model versions or only suppliable as optional
equipment for certain models.
No.
Power consumer
Amperes
1
Not assigned
2
START - STOP
5
3
Instrument cluster, headlamp beam adjustment
7,5
4
ABS control unit
5
5
Petrol engine: Cruise control system
5
6
Reversing light (manual gearbox)
10
7
Ignition
15
Engine control unit, automatic gearbox
7,5
8
Brake pedal switch, coolant fan
5
9
Operating controls for the heating, control unit for air condi- tioning system, parking aid, control unit for cornering lights, coolant fan
5
10
Air conditioning
a)
7,5
11
Mirror adjustment
5
12
Control unit for trailer detection
5
13
Control unit for automatic gearbox
5
14
Motor for halogen projector headlights with cornering light function
10
15
Navigation PDA
5
16
Electrohydraulic power steering
5
17
START - STOP - radio
10
Daylight driving lights
7,5
18
Mirror heater
5
19
S-contact
5
20
Engine control unit
5
Engine control unit
7,5
Fuel pump relay
15
Fuel pump control unit
15
21
Reversing light, fog lights with the function “CORNER”
10
22
Operating controls for the heating, control unit for air condi- tioning system, parking aid, mobi
le phone, instrument cluster,
steering angle sender
, ESP, vehicle voltage control unit, multi-
function stee
ring wheel
7,5
23
Interior lighting, storage compartment and luggage compart- ment, side lights
15
24
Central control unit of the vehicle
5
25
Seat heaters
20
26
Rear window wiper
10
27
Not assigned
28
Petrol engine: AKF valve, petrol engine: Control flap
10
29
Injection, water pump
10
No.
Power consumer
Amperes
s3j8.a.book Page 196 Tuesday, April 20, 2010 1:10 PM