2010 SKODA FABIA fuse

Fuses and light bulbs
195
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Fuses and light bulbsElectric fusesReplacing fuses in the dash panel Defect fuses must be replaced.Individual electrical circuits are protected by
fuses. The fuses are located on the left
side of the dash panel behind the safety cover. – Switch the ignition off and also the electrical component affected.– Carefully swivel the cover in the direction of arrow and pull it out
fig. 161
.
– Find out which fuse belongs to th
e component which is not operating
page 196,
“Fuse assignment in
the dash panel”.
– Take the plastic clip out of it
s fixture in the fuse cover, insert it onto the respective
fuse and pull out this fuse.
– Defect fuses can be detected by their melted metal strips. Replace the defect fuse
by a new fuse of the
same
ampere number.
– Insert the fuse cover into the dash pane
l in such a way that the guide lugs are
guided into the openings of the dash
panel and then lock them by pressing.
We recommend that you always have repl
acement fuses in your vehicle. You can
obtain replacement fuses from the range of
Škoda original parts or from a specialist
garage
14).
Colour coding of fuses
Caution

Never attempt to “repair” fuses and also do
not replace them with a fuse of a higher
amperage - risk of fire! This may also caus
e damage at another part of the electrical
system.
Have the electrical system checked as quickly as possible by a specialist garage if a
newly inserted fuse blows again after a short time.
Note
We recommend that you have these fuse
s replaced by a specialist garage.
Fig. 161 Bottom side of the dash panel: Fuse cover
14)The small box with replacement fuses is part of
the basic equipping of th
e vehicle in some coun-
tries.
Colour
Maximum amperage
light brown
5
brown
7,5
red
10
blue
15
yellow
20
white
25
green
30
s3j8.a.book Page 195 Tuesday, April 20, 2010 1:10 PM

Fuses and light bulbs
196
Fuse assignment in the dash panelFig. 162 Schematic representation of the fuse
box for vehicles with left-hand steering / right-
hand steeringCertain electrical components are only standard on certain vehicle model versions or only suppliable as optional
equipment for certain models.
No.
Power consumer
Amperes
1
Not assigned
2
START - STOP
5
3
Instrument cluster, headlamp beam adjustment
7,5
4
ABS control unit
5
5
Petrol engine: Cruise control system
5
6
Reversing light (manual gearbox)
10
7
Ignition
15
Engine control unit, automatic gearbox
7,5
8
Brake pedal switch, coolant fan
5
9
Operating controls for the heating, control unit for air condi- tioning system, parking aid, control unit for cornering lights, coolant fan
5
10
Air conditioning
a)
7,5
11
Mirror adjustment
5
12
Control unit for trailer detection
5
13
Control unit for automatic gearbox
5
14
Motor for halogen projector headlights with cornering light function
10
15
Navigation PDA
5
16
Electrohydraulic power steering
5
17
START - STOP - radio
10
Daylight driving lights
7,5
18
Mirror heater
5
19
S-contact
5
20
Engine control unit
5
Engine control unit
7,5
Fuel pump relay
15
Fuel pump control unit
15
21
Reversing light, fog lights with the function “CORNER”
10
22
Operating controls for the heating, control unit for air condi- tioning system, parking aid, mobi
le phone, instrument cluster,
steering angle sender
, ESP, vehicle voltage control unit, multi-
function stee
ring wheel
7,5
23
Interior lighting, storage compartment and luggage compart- ment, side lights
15
24
Central control unit of the vehicle
5
25
Seat heaters
20
26
Rear window wiper
10
27
Not assigned
28
Petrol engine: AKF valve, petrol engine: Control flap
10
29
Injection, water pump
10
No.
Power consumer
Amperes
s3j8.a.book Page 196 Tuesday, April 20, 2010 1:10 PM

Fuses and light bulbs
197
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Replacing fuses at the battery (manual gearbox, automatic gearbox DSG)Fig. 163 The battery: Fuse cover
30
Fuel pump
15
Ignition
20
Cruise control system, operation of PTC relay
5
31
Lambda probe
10
32
High pressure pump, pressure valve
15
33
Engine control unit
30/15
34
Engine control unit
15
Vacuum pump
20
35
Power supply of ignition lock
5
36
Main beam light
15
37
Rear fog light
7,5
38
Fog lights
10
39
Blower
30
40
Heatable windscreen washing no
zzles, windscreen cleaning
system
15
41
Not assigned
42
Rear window heater
25
43
Horn
20
44
Front window wiper
20
45
Central control unit fo
r convenience system
25/10
46
Anti-theft alarm system
15
47
Cigarette lighter, power socket in the luggage compartment
b)
15
48
ABS, START-STOP - DC/DC converter ESP
15
49
Turn signal lights, brake lights
15
No.
Power consumer
Amperes
50
START-STOP - DC/DC converter infotainment
30
Radio
10
51
Electrical power window (front and rear) - left side
25
52
Electrical power window (front and rear) - right side
25
53
Parking light - left side
5
Electric sliding/tilting roof
25
54
START-STOP - instrument cluster
5
Anti-theft alarm system
15
55
Control unit for automatic gearbox DSG
30
56
Headlight cleaning system
25
Parking light - right side
5
57
Left low beam, headlight range adjustment
15
58
Low beam on the right
15
a)Only valid for some countries.b)If the engine is switched off already one electr
ical component which is
connected can discharge
the battery.No.
Power consumer
Amperes
s3j8.a.book Page 197 Tuesday, April 20, 2010 1:10 PM

Fuses and light bulbs
198
– Press together the interlocks of the fuse
cover simultaneously in direction of arrow
page 197, fig. 163
and push out the cover in direction of arrow .
– Release the fixtures in the openings using a flat screwdriver and fold the cover
upwards in direction of arrow .
– Find out which fuse belongs to th
e component which is not operating.
– Defect fuses can be detected by their melted metal strips. Replace the defect fuse
by a new fuse of the
same
ampere number.
Caution

Never attempt to “repair” fuses and also do
not replace them with a fuse of a higher
amperage - risk of fire! This
may also cause damage at an
other part of the electrical
system.
Have the electrical system checked as quickl
y as possible by a specialist garage if a
newly inserted fuse blows again after a short time.
Note
We recommend that you have these fuse
s replaced by a specialist garage.
Fuse assignment at the battery (manual gearbox, automatic gearbox DSG)Certain electrical components are only standard on certain vehicle model versions or only suppliable as optional
equipment for certain models.
Caution
Observe the following guidelines

in “Replacing fuses at the battery (manual
gearbox, automatic gearbox DSG)” on page 197.
Note
The fuses 1 - 7 can be replac
ed by a specialist garage.
AA
AB
AC
AD
Fig. 164 Schematic representation of fuse assignment at battery
No.
Power consumer
Amperes
1
Dynamo
175
2
Not assigned
3
Interior
80
4
Electrical auxiliary heating system
60
5
Interior
40
6
Glow plugs, coolant fan
50
7
Electrohydraulic power steering
50
8
ABS or TCS or ESP
25
9
The radiator fan
30
10
The radiator fan
5
11
ABS or TCS or ESP
40
12
Central control unit
5
13
Automatic gearbox electrical auxiliary heating system
540
s3j8.a.book Page 198 Tuesday, April 20, 2010 1:10 PM

Fuses and light bulbs
199
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Replace fuses at the battery (automatic gearbox)Fig. 165 The battery: Open the posi
tive terminal cover / fuse cover
– Open the positive terminal cover (+)
fig. 165
- left.
– Press onto the interlocks of the fuse covers
fig. 165
on the right and open the
covers.
– Press together the interlocks of the fuse
cover simultaneously and push out the
cover in the direction of the arrow.
– Find out which fuse belongs to th
e component which is not operating
page 199,
“Fuse assignment at the ba
ttery (automatic gearbox)”.
– Defect fuses can be detected by their melted metal strips. Replace the defect fuse
by a new fuse of the
same
ampere number.
Caution

Never attempt to “repair” fuses and also do
not replace them with a fuse of a higher
amperage - risk of fire! This
may also cause damage at an
other part of the electrical
system.
Have the electrical system checked as quickl
y as possible by a specialist garage if a
newly inserted fuse blows again after a short time.
Note

We recommend that you have these fuse
s replaced by a specialist garage.

Some vehicles are only fitted with the cover
fig. 165
.
Fuse assignment at the battery (automatic gearbox)Certain electrical components are only stan
dard on certain vehicl
e model versions or
only suppliable as optional
equipment for certain models.
AAABAB
No.
Power consumer
Amperes
1
Dynamo
175
2
Interior
80
3
Electrical auxiliary heating system
60
4
ESP
40
5
Electrohydraulic power steering
50
6
Glow plugs
50
7
ESP
25
8
The radiator fan
30
9
Air conditioning system
5
10
ABS
40
11
Central control unit
5
12
Automatic gearbox electrical auxiliary heating system
540
Fig. 166 Schematic representation of fuse assignment at battery
s3j8.a.book Page 199 Tuesday, April 20, 2010 1:10 PM

Fuses and light bulbs
200
Caution
Observe the following guidelines

in “Replace fuses at the battery (automatic
gearbox)”.BulbsReplacing bulbsThe relevant lamp must always be switch
ed off before a light bulb is replaced.
Do not take hold of the glass bulb with naked fingers (even the smallest amount of dirt reduces the working life of the light bulb).
Use a clean cloth, serviette or something
similar. Defect light bulbs should only be replaced
with light bulbs of the same type. The desig-
nation is located on the ligh
t socket or the glass bulb.
Changing certain bulbs is not something whic
h you can do yourself, but requires to be
done by a specialist. Other parts of the vehicle must be removed in order to change the light bulbs. This applies, in particular, to
bulbs which can only be reached from the
engine compartment. We therefore recommend that you have any
bulbs changed by a specialist garage or,
in exceptional cases, by calling
on other professional assistance.
Please note that the engine compartment is a hazardous area
page 166, “Working
in the engine compartment”. We recommend that you always have a small box of replacement bulbs in your vehicle. You can obtain replacement bulbs from Škoda
original accessories or from a specialist
garage
15).
A stowage place for the bulbs is located in the box in the spare wheel.Bulb - Overview15)The small box with replacement bulbs is part of
the basic equipping of th
e vehicle in some coun-
tries.
Front headlight
Halogen headlight
Halogen projector
headlights
Low beam light
H4
H7
Main beam light
H4
H7
Parking lights
W5W, LED
a)
a)Valid for vehicles Scout.Turn signals
PY21W
Fog lights*
H8/HB4
a)
Daylight driving lights*
P21W, LED
b)
b)Valid for RS vehicles with separate lights* for daylight driving lights.Rear light unit
Bulb
Reversing light
P21W
Turn signals
PY21W
Brake lights
P21W
Rear fog light
P21W
Parking lights
2x W5W
Others
Bulb
Side turn signal lights
WY5W
Licence plate light
C5W / T4W (5W)
3. Brake light
LED
Interior lighting front / rear
C10W
Reading lights
W5W
Luggage compartment light
W5W
Lighting in storage compartment
W5W
s3j8.a.book Page 200 Tuesday, April 20, 2010 1:10 PM

Fuses and light bulbs
201
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING

Bulbs H7 and H4 are pressurised and
may burst when changing the bulb -
risk of injury!
It is recommended to wear gloves and
safety glasses when changing a bulb.
Note
This Owner's Manual only describes the replacement of bulbs where it is assumed that no major complications will
arise. Other light bulbs should be replaced by your
specialist garage.Front headlightFig. 167 Fitting position of the bulbs: Halo
gen headlights / halogen projector headlights
Positions of the light bulbs in the halogen headlights
fig. 167
on the left and in the
halogen projector headlights
fig. 167
on the right.
- low beam, main beam and side lights - front turn signal light - low beam light - main beam and side lights - front turn signal light
Low beam and main beam (halogen headlights)– Open the bonnet.– Remove the protective cap
fig. 167
.
– Pull off the connector from the lamp, rele
ase the sprung wire clamp and pull out
the lamp towards the rear
fig. 168
.
– Replace the lamp H4, insert into the opening in the reflector (with the fixing lugs in
the recesses), secure with the sprung wi
re clamp, mount the connector and posi-
tion the protective cap.
– We recommend that you have the headli
ght setting checked by a Skoda Service
Partner after replacing the light bulb.
Low beam (halogen projector headlights)– Open the bonnet.
AAABA1A2A3
Fig. 168 Removing the light bulb for the low beam and main beam light
AA
Fig. 169 Removing the light bulb for the low beam light
s3j8.a.book Page 201 Tuesday, April 20, 2010 1:10 PM

Fuses and light bulbs
202
– Remove the protective cap
page 201, fig. 167
on the right.
– Turn the connector with the light bulb up to the stop towards the left
page 201,
fig. 169
and remove.
– Replace the halogen lamp H7, insert the connector with the new halogen lamp and
turn to the right up to the stop.
– Insert the protective cap.– We recommend that you have the headlight setting checked by a Skoda Service
Partner after replacing the light bulb.
Main beam (halogen projector headlights)– Open the bonnet. – Remove the protective cap
page 201, fig. 167
on the right.
– Turn the connector with the light bulb
up to the stop towards the left
fig. 170
and
remove.
– Replace the halogen lamp H7, insert the connector with the new halogen lamp and
turn to the right up to the stop.
– Insert the protective cap.– We recommend that you have the headlight setting checked by a Skoda Service
Partner after replacing the light bulb.
Turn signal light (at the front)– Open the bonnet. – Turn the socket (halogen headlight)
page 201, fig. 167
or the socket
(halogen projector headlight) to the left an
d take it out together with the light bulb
for the turn signal light.
– Replace the defective light bulb.– Insert the lamp holder with light bulb into
the headlight. Secure the lamp holder by
turning it to the right until it locks in place.
Parking light at the front– Open the bonnet. – Remove the protective cap (halogen headlight) or (halogen projector head-
light)
page 201, fig. 167
.
– Grasp the light bulb holder and pull it out of the headlight.– Replace the light bulb in the light bulb
holder and re-insert into the headlight.
Daylight driving lights and fog lightsFig. 171 Front bumper: Protective
grille / removing the fog light
– Switch the ignition and all lights off. – Grasp the grille at the points marked with the arrows
fig. 171
- left and take it out.
A1
Fig. 170 Removing the light bulb for the main beam light
A2
AB
A3
AA
A2
s3j8.a.book Page 202 Tuesday, April 20, 2010 1:10 PM