2010 Seat Leon 5D radio controls

Introduction
8Unit overview
D Rotary/push knob.
− Press to switch on and off ⇒page 10.
− Turn to adjust the base volume ⇒ page 10.
Press to activate a function area.
− : switch on the radio and change frequency band ⇒page 14.
− : change to Media mode ⇒page 29. −
: switch on the Telephone function ⇒ page 75.
− : open the Navigation main menu ⇒page 47.
− : display stored traffic news (TMC) ⇒page 71.
− : open a context-sensitive setup menu for the selected mode,
and switch on sound and system settings ⇒page 87.
Fig. 1 Overview of the controls.
A1A2
RADIOMEDIA
PHONENAVTRAFFICSETUP
MediaSystem2.1_EN.book Seite 8 Donnerstag, 29. April 2010 4:18 16

Introduction
12Function buttons and unit buttonsThe unit is equipped with a touchscreen.
The currently selected menu is displayed in the centre of the bottom line of
the screen.
Controls•Rotary/push knobs.•Labelled unit buttons .•Function buttons on the unit.•Function buttons displayed on the screen.
Rotary/push knobs
The left-hand rotary/push knob ⇒page 8, fig. 1 is referred to as the
volume control
D or the on/off switch.
The central rotary/push knob ⇒page 8, fig. 1 is referred to as the setting
knob. Unit buttons
This manual uses the word “unit button” and a symbol to refer to buttons
on the unit, e.g. the unit button.
There are two unlabelled unit buttons below the screen
⇒page 8, fig. 1 .
Each has the same function and is operated in the same way as the function
button displayed on the screen above it ⇒fig. 2 and .
Unit buttons are operated either by pressing or pressing and holding them.
Function buttons on the screen.
Active areas of the screen that call up a certain function are called “function
buttons”. These buttons are operated by briefly pressing the screen or by
pressing and holding . Function buttons are referred to in this manual with the
button symbol and the word “function button”.
If a function button on the screen has a grey background, it is disabled,
e.g. ⇒fig. 2 .
Pop-up window
A “pop-up window” is a small window that is temporarily displayed on top
of the current menu and contains additional function buttons.
Function buttons in pop-up windows can be selected by pressing them. This
closes the pop-up window.
Press the unit button to close the pop-up window without making any
changes.
Starting functions or enabling functions using “checkboxes”
Some functions are started and stopped by pressing a button, for example
the scan function ⇒ page 16.
Other functions and displays are permanently activated or deactivated and
are controlled via checkboxes.
A tick in the checkbox
’ indicates that the function is enabled, and an empty
checkbox
‰ means that it is disabled.
Fig. 2 RADIO main menu
with pop-up window.
A1
A10
...
RADIO
A11
AA
AC
...AC
AB
E
MediaSystem2.1_EN.book Seite 12 Donnerstag, 29. April 2010 4:18 16

Audio mode35
be used to play audio from an external player connected to a Rear Seat Enter-
tainment (RSE ) device through the vehicle sound system
2).
The audio from the external player connected to the RSE is played through the
vehicle loudspeakers but cannot be controlled with the radio and navigation
system controls.
An external audio source connected to the socket is indicated by AUX2 on the
screen.
Playing audio from an RSE system using an additional external audio source
•Lower the base volume on the radio-navigation system ⇒page 10.•Connect the external player to the AUX-RSE connector in the vehicle and
start playback on the external player in accordance with the instructions
given in the RSE handbook.•In Media mode, press the unit button to open the Media setup
menu . Tick the checkbox Activate AUX2 input so that the AUX2 source is
shown in the Media selection menu
3) ⇒ page 34, fig. 28 .
•In the MEDIA main menu, press the unit button to open the Media
selection menu .•Press the AUX2 ⇒ page 34, fig. 29 function button to start playback of the
external audio source connected to the RSE over the vehicle speakers.
The output volume of the connected external audio source should be
adjusted to the volume of the other audio sources ⇒page 41 ( AUX2 volume
in the Media settings menu ⇒ page 34, fig. 28).
Things to note about the AUX2 additional external audio source•If another audio source (CD, SD, etc.) is selected during playback, the
external player connected to the RSE continues playing.
•When playback on the external audio source has finished or if the external
player is disconnected from the AUX-RSE connector, the radio and navigation
system remains in the AUX2 menu.•The AUX2 symbol remains visible and on (highlighted in red), and there-
fore accessible, as long as the “ Activate AUX2 input” check box in the (Media
setup menu ) is ticked. The option should be deactivated when playback has
finished.
Recommendations for use•If your vehicle is not fitted with an RSE system or a MEDIA-IN or MDI multi-
media interface, we recommend that the Activate AUX2 input is always left
unticked . Otherwise, the AUX2 source (if your vehicle does not have MDI) or
the “MDI” source may be shown in the Media selection menu as “active”
(accessible), even if there is no audio source connected to them.•If your vehicle is fitted with a MEDIA-IN or MDI multimedia interface , the
AUX2 additional external source is not available. Use the check box Activate
AUX2 input as described in the section MEDIA-IN or MDI multimedia
interface .
2)If the vehicle is supplied from the factory with an RSE system connected to the radio
and navigation system.3)This option can also be activated using the function button in the pop-up window
which appears when you try to go to the MEDIA main menu when there is no media
source connected or activated.
SETUP
MEDIA
MediaSystem2.1_EN.book Seite 35 Donnerstag, 29. April 2010 4:18 16

Audio mode45
When should it be activated?•LEON: to play audio from an iPod (via the SEAT adapter cable) or from an
external device connected to the AUX input of the MEDIA-IN interface.•ALTEA, ALTEA XL, Freetrack: to play audio from an external player
connected to the AUX input of the Rear Seat Entertainment system (if fitted in
the vehicle)
iPod® and iPhone
®
When an iPod
® or iPhone
® is connected, a special iPod selection menu is
displayed at the top selection level of the track view ⇒page 43, fig. 41. This
iPod selection menu always has the same structure and is operated in the
familiar way.
The music controls on the connected iPod
® or iPhone
® are disabled.
The output volume of a connected iPod
® or iPhone
® should be adjusted to
the volume of the other audio sources ⇒ page 41.Possible error messages after connecting an external data medium
Note
External audio sources connected to the AUX socket of the MEDIA-IN interface
can be played through the radio and navigation system, but cannot be
controlled from there. To control the external audio source, please see the
manufacturer's instructions. As long as the external audio source is not
switched off, it will continue operating even if another source starts to play in
the radio and navigation system.
Note
The MDI symbol remains visible and on (highlighted in red), and therefore
accessible, as long as the “Activate AUX2 input” check box (Media setup
menu) is ticked. The option should be deactivated when playback has
finished.Error message
Cause
Procedure
Device not
supported
Playback from the
external data medium
or communication via
the adapter cable used
is not possible.
Check adapter cable.
Update the software of the
MEDIA-IN multi-media inter-
face at your Authorised Serv-
ice.
If possible, update the soft-
ware of the external data
medium.
Unit not ready for
operation
Communication inter-
rupted.
Check the connection and
make sure the external data
medium is working correctly.
Due to the large number of different data media and various iPod
® and
iPhone
® generations available, it is not possible to guarantee fault-free
operation of all functions described here.
MediaSystem2.1_EN.book Seite 45 Donnerstag, 29. April 2010 4:18 16

Index91
Index
AAddress entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
AM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 90
Anti-theft protection
Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Radio coding . . . . . . . . . . . . . . . . . . . . . . . . . 10
Areas with special regulations . . . . . . . . . . . . . . 76
Autoscan MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Autozoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
AUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33, 90 AUX volume . . . . . . . . . . . . . . . . . . . . . . . . . . 41
AUX-IN multimedia socket . . . . . . . . . . . . . . 33
External audio source . . . . . . . . . . . . . . . . . . 33
AUX 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 External audio source . . . . . . . . . . . . . . . . . . 34
AUX2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
AUX-IN multimedia socket See: AUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Avoiding hold-ups . . . . . . . . . . . . . . . . . . . . . . . . 70BBalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Base volume Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Mute function . . . . . . . . . . . . . . . . . . . . . . . . . 11 Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Bluetooth audio (external audio source) . . . . . . 36
BT audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Button tone
See: Confirmation tone . . . . . . . . . . . . . . . . . 88
CCabriolet models (ejecting CDs) . . . . . . . . . . . . . 32
Car park search . . . . . . . . . . . . . . . . . . . . . . . . . . 55
CD eject in Cabriolet models . . . . . . . . . . . . . . . . 32
CD mode
See: MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Changing frequency band . . . . . . . . . . . . . . . . . . 15
Changing station names . . . . . . . . . . . . . . . . . . . 22
Checkbox – ticking and clearing . . . . . . . . . . . . 12
Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Confirmation tone Switching on and off . . . . . . . . . . . . . . . . . . . 88
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Coordinates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Cursor See: "Enter mark" . . . . . . . . . . . . . . . . . . . . . 51
DDAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24, 90Additional services . . . . . . . . . . . . . . . . . . . . 24
Additional stations from the main menu . . . 25
Additional stations on the DAB station list . 27
Changing an ensemble . . . . . . . . . . . . . . . . . 26
Changing station . . . . . . . . . . . . . . . . . . . . . . 26
Changing stations . . . . . . . . . . . . . . . . . . . . . 25
Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Deleting station list . . . . . . . . . . . . . . . . . . . . 27
Ensemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
FM programme tracking . . . . . . . . . . . . . . . . 28
Incoming messages . . . . . . . . . . . . . . . . . . . 24
Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Programme tracking . . . . . . . . . . . . . . . . . . . 28
Radio text . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Selecting a station . . . . . . . . . . . . . . . . . . . . . 26
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Station list . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Switching incoming messages on or off . . . 27
Switching on . . . . . . . . . . . . . . . . . . . . . . . . . 25
Updating the station list . . . . . . . . . . . . . . . . 27
Data, deleting See: Deleting . . . . . . . . . . . . . . . . . . . . . . . . . 88
Day or night design . . . . . . . . . . . . . . . . . . . . . . . 88
Delete Telephone user profile . . . . . . . . . . . . . . . . . 80
MediaSystem2.1_EN.book Seite 91 Donnerstag, 29. April 2010 4:18 16