2010 Seat Leon 5D buttons

Navigation
58Destination memoryIntroductionThe destination memory is used to store navigation destinations manually.
The function buttons for storing a destination are only enabled when the
destination has been sufficiently defined.
Destinations saved in the memory can be edited or used to navigate to the
destination.
Additional Information:•Safety notes
’ ⇒ page 6
•Unit overview ⇒page 8•Introduction to navigation ⇒page 47•Entering a destination ⇒page 52
Automatically stored last destinationsUp to 50 destinations for which route guidance has been started are automat-
ically stored in the Last destinations list ⇒fig. 56 .
Old last destinations are automatically overwritten by new destinations when
the list is full. To permanently retain one of the last destinations, it must be
stored in the Destination memory .•In the list of last destinations, mark the destination you wish to store
⇒ fig. 56.•Press the function button and store the destination ⇒page 59.
Fig. 56 List of recent
destinations.
Store
MediaSystem2.1_EN.book Seite 58 Donnerstag, 29. April 2010 4:18 16

Navigation
64changed while route guidance is in progress. The route will then be recalcu-
lated.•Press the unit button in one of the navigation menus.•In the Navigation setup menu , press the function button
⇒ page 63, fig. 63.•Select or deselect an option by ticking or clearing the appropriate
checkbox ⇒page 63, fig. 64 .
Defining route criteria •In the Route options setup menu , press the function button.•Press the desired settings to select them in the pop-up window.
Dynamic route
If dynamic route guidance is activated, TMC traffic reports will be taken into
account in the route calculation ⇒page 70.
Excluding types of route in the calculation
The function buttons , etc. define whether or not these
types of road may be included in the route calculation.
Even when excluded, these types of route will still be included in the route
calculation if no practical alternative route exists. For example, if it is impos-
sible to reach an island without using the ferry. For the calculation of very long
routes, it is not possible to avoid motorways.
Navigation announcementsWhen the route has been calculated, the first announcement is given. Up to
three navigation announcements are given before a turn, e.g. within a town
“Prepare to turn left”, “Turn left after 300 metres” and “Now turn left”.•Press the setting knob ⇒page 8, fig. 1 to hear the last navigation
announcement again.
The distances that are announced depend on the type of road and the speed
at which you are driving. On motorways, the first announcement is given
roughly 2,000 m before an exit.
For example, the following announcements may be heard on multi-lane high-
ways or roads that divide, and at roundabouts: “Take the second exit at the
roundabout!”.
When you arrive at your destination, the following announcement is heard:
“You have reached the destination”.
During dynamic route guidance, you receive information about reported
traffic congestion on the route. If the route is recalculated due to traffic
congestion, you will be advised accordingly ⇒page 70.
Announcement settings.
Navigation announcements are played at the preset volume.
The volume of an announcement can be changed with the volume control
D.
All following announcements will then be made at this volume.
The volume of navigation announcements can be preset or switched off in the
Navigation setup menu ⇒ page 73 or in the volume settings ⇒page 88.
Route criteria
MeaningFastest route to the destination, even if it means driv-
ing further.This function aims to find an equilibrium between the
shortest time and the shortest route.Shortest route to the destination, even if it results in a
longer travelling time. The navigation route may
include unusual route sections, e.g. dirt roads.
SETUP
Route optionsRoute criteria
FastEconomicalShort
˜Avoid motorways
A10
MediaSystem2.1_EN.book Seite 64 Donnerstag, 29. April 2010 4:18 16

Navigation65
Visual recommendations on the mapWhen route guidance starts, the system automatically switches to the map
view ⇒fig. 65. The red
9 symbol indicates the vehicle's position and heading
⇒fig. 65 . If
the vehicle position symbol
9 remains in the same position and the map
view freezes, it is currently not possible to determine the vehicle's position,
e.g. in a multi-storey car park.
During route guidance the navigation route is shown as a blue line. Sections
closed to traffic either manually or due to TMC messages advising of traffic
congestion ⇒page 70 are shown in colour on the calculated route.
The next road to take is displayed in the top line of the screen.
After a few seconds, the function buttons disappear from the bottom line of
the screen to display more information on the route ⇒fig. 66.
•Briefly press the bottom-right or bottom-left area of the screen to display
the function buttons again ⇒ fig. 65.•Pressing the unit button switches between the Navigation main
menu and the map view.
When the function buttons are hidden, the current street and information
about the journey length are displayed on the bottom line of the screen
⇒ fig. 66 .: Remaining distance to the destination.: Expected time of arrival or travelling time ⇒page 73.
Shortly before you reach a turning point, a turning arrow appears, indicating
the direction to turn. The distance to the turning point is also displayed below
it.
Changing the map scale (Autozoom)
The “Autozoom” function is enabled for the map view by default. This means
that the map view automatically zooms in and out: Small scale on motorways.
Large scale in urban areas.•Turn the setting knob ⇒page 8, fig. 1 to manually change the scale
of the map for a few seconds. Turn the knob clockwise to zoom in. Turn the
knob anticlockwise to zoom out.
Fig. 65 Map view during
route guidance with the
function buttons
displayed.Fig. 66 Map view during
route guidance.
NAV
A10
MediaSystem2.1_EN.book Seite 65 Donnerstag, 29. April 2010 4:18 16

Navigation
66•To permanently retain the manually selected map scale, “Autozoom”
must be deactivated in the Navigation setup menu ⇒ page 73.
Selecting the map view mode
The map view mode can be changed.•In the map, briefly press the bottom-right or bottom-left area of the screen
to display the function buttons again.•Press the function button ⇒page 65, fig. 65 .•Select one of the playback modes displayed in the pop-up window.
: two dimensions, map oriented to North.
: two dimension, map oriented to vehicle heading.
: three dimensions, birds-eye view of map.
Alternatively, it is possible to switch between the three map views by pressing
on the compass shown on the map.
During route guidance, the calculated route can also be shown on an over-
view map.•Press in the pop-up window to display current position and
destination.
The scale of the overview map cannot be changed.•Press the function button to return to the last shown map view.
Displaying speed limits
If there is a speed limit stored in the navigation data for the road along which
you are travelling, this will be displayed on the map. During route guidance,
the arrow indicating a change of direction takes precedence over the speed
limit display.
Please remember that the navigation data may not be up-to-date and that the
system has limitations ⇒ page 47! The speed limit display is activated in the navigation system settings
⇒
page 73.
Points of interest on map
Depending on the programmed settings, points of interest (petrol stations,
car parks, Authorised Services) will be displayed as symbols on the map
⇒ page 73.
Note
If you miss a turning during route guidance and are currently unable to turn
back, keep on driving until the navigation system offers a new route.
Note
T he q ua lit y o f the i nst ru cti ons g ive n by th e uni t will d e pe nd o n th e navi gat io n
data used.
Note
In addition, the route is optimised with the TMC traffic news received
⇒page 70. The radio stations broadcasting this information are responsible
for the content and the quality of the TMC traffic reports.
Extras
2D North2D Heading3D Heading
Overview map
Back
MediaSystem2.1_EN.book Seite 66 Donnerstag, 29. April 2010 4:18 16

Navigation67
Stopping and resuming route guidanceActive route guidance can be stopped and later resumed from the new vehicle
position at any time. Stopping route guidance
•In the
map view , briefly press the bottom-right or bottom-left area of the
screen to display the function buttons.•Press the function button ⇒fig. 67 .•ALTERNATIVELY: Switch to the main menu Navigation and press the
function button.
Resume route guidance to the last destination•In the map view , pressing the function button always automatically
resumes route guidance to the last destination ⇒fig. 68 .Entering a stopover destinationIt is possible to enter one additional destination as a stopover destination
while route guidance is in progress. You will then always be guided to the
stopover destination first before route guidance continues to the final desti-
nation. The final destination is always the destination to which route guid-
Fig. 67 Stopping route
guidance.Fig. 68 Route guidance
interrupted.
Stop
Stop
Start
Fig. 69 Information
window showing a stop-
over destination during
route guidance.
MediaSystem2.1_EN.book Seite 67 Donnerstag, 29. April 2010 4:18 16

Navigation71
•Alternatively: press the and buttons successively to
open the setup menu TRAFFIC .•In one of the two menus, tick or clear the checkbox in the
function button by pressing it.
Traffic incidents displayed on the map
Traffic congestion reported via TMC that is on the route is shown on the map
by a coloured symbol. Traffic congestion that is not on the route is shown on
the map by a grey symbol. The position ing of the TMC symbol indicates the
start and the direction of the traffic congestion if both are clearly defined in
the TMC traffic message.
Route sections with traffic congestion that are on the route are coloured red.
Route sections with traffic congestion that are not on the route are coloured
grey. If route guidance is not active, all traffic congestion is coloured grey.
Dynamic route guidance
If the function button is activated and a diversion to avoid
traffic congestion on the route is likely to save time, the navigation system
automatically calculates an alternative route.
An announcement is given when the route is recalculated. The same
announcement is given if traffic congestion that was present when the route
was originally calculated is now no longer reported.Note
A diversion of the route based on TMC traffic reports may not always save
time, if, for instance, there is also heavy traffic on the alternative route.
Note
If there is traffic congestion on a route section further ahead, it is possible to
exclude the section manually if the TMC traffic report has not yet been
received.
Displaying TMC traffic reports (TRAFFIC)The unit constantly receives TMC traffic reports in the background, provided
a TMC traffic news station can be received at the current location. The station
listened to does not have to be the TMC traffic news station.
TRAFFIC
SETUP
Dynamic route
’ Dynamic route
Fig. 72 List of TMC traffic
reports received.F ig. 73 Detailed view of a
received TMC traffic
report.
MediaSystem2.1_EN.book Seite 71 Donnerstag, 29. April 2010 4:18 16

Navigation
72The unit only processes and displays TMC traffic reports affecting the area
within a radius of roughly 100 km from the current vehicle position.
TMC traffic reports are required for dynamic route guidance and are displayed
on the map ⇒ page 70.
Display TMC traffic reports•Press the unit button to display the list of the current TMC traffic
reports ⇒page 71, fig. 72 .•Press one of the TMC traffic reports on the screen to open the detailed
view ⇒page 71, fig. 73 .•Alternatively: select the TMC report by turning the setting knob
⇒ page 8, fig. 1 and open the detailed view by pressing ⇒page 71,
fig. 73 .•In the detailed view, you can browse through the TMC traffic reports using
the function buttons and .
Display TMC traffic news stations•Open the list of the current TMC traffic reports.•Press the ⇒page 8, fig. 1 unit button to open the information
window. The current TMC traffic news station is displayed.•Press the unit button again to close the information window.Note
By using the ⇒ page 71, fig. 72 function button it is
possible to enter a manual exclusion from the vehicle position ⇒page 70.
Note
The radio-navigation system can only process and store TMC traffic reports if
the unit has access to navigation data for the area you are currently travelling
through.
Note
The quality of the dynamic route guidance depends on the information
contained in the TMC traffic reports. Th e radio stations are responsible for the
content of the news broadcast.Route guidance in demo modeIf demo mode is activated in the Navigation setup menu ⇒ page 73, an addi-
tional pop-up window opens when you start route guidance.•Pressing the function button starts a “virtual route guidance” to
the destination you have entered.•If you press the function button, a “real route guidance” starts.
The sequence of events and the operations in virtual route guidance are
similar to those in real route guidance.
Virtual route guidance is repeated when you reach the fictitious destination
and always starts again from the starting point if it is interrupted.
If the starting point for demo mode has been defined manually in the
Navigation setup menu , virtual route guidance will start from this position.
If the vehicle is moved and the unit can determine its current location by GPS,
any manually entered starting point will be overwritten with the current
vehicle location ⇒ page 73.
When real route guidance is started following virtual route guidance in demo
mode, the unit first has to reorient itself. This may take some time, depending
on the number of satellites the unit can currently receive. Moving the vehicle
may speed up the reorientation process.
TRAFFICA10Previous
Next
º
A7
ºCongestion ahead
DemoNormal
MediaSystem2.1_EN.book Seite 72 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)
80The columns below the Bluetooth
® symbol show the strength of the current
signal (strength of signal from the main mobile phone station).
To display the above, the mobile phone should accept the handsfree profile
1.5 .
Function buttons in the PHONE main menu : dial.
: address book.
: missed calls.
6): numbers dialled.
: calls received.
: voice mailbox number
7).
: accept or make a call.
8): make emergency call.
Setup menu Telephone (SETUP)The functions activated with the button are required for the
connection of a mobile phone or an external Bluetooth device ⇒page 77.6)This may vary depending upon the country.7)The number of the voice mailbox should be entered manually in the telephone setup
menu ⇒ page 80.8)The SOS or emergency call function is not displayed on all appliances and is not avail-
able in all countries even through the mobile phone operator.AAABACADAEAFSOS
Bluetooth settings
Function button: Result
: enter the voice mailbox number.: the telephone book entries in the radio and navigation
system will be updated from the mobile phone and SIM card. The proce-
dure may last several minutes.: sets the volume of phone calls.: Restore factory settings in telephone menu and delete
user profiles and numbers stored.
Enter voice mailboxLoad address bookTe leph on e vol umeFactory settings
MediaSystem2.1_EN.book Seite 80 Donnerstag, 29. April 2010 4:18 16