2010 Seat Ibiza SC technical specifications

If and when211
Safety First
Operating Instructions
Practical Tips
Technical Specifications
It also contains the instructions for using the compressor.
WARNING
•Do not attempt to repair a puncture with the sealing compound if the
tyre has been damaged by driving the vehicle after the tyre has lost its air.•Always observe warnings and follow safety instructions concerning
compressor and sealing compound carefully.•Do not drive faster than 80 km/h, avoid heavy acceleration, hard
braking and fast cornering.•Tyres which have been repaired with sealing compound are only suit-
able for temporary use over a short period. Therefore, please drive carefully
to the next available specialised workshop.For the sake of the environment
If you have to dispose of a sealant container, go to a specialised waste service
or to a SEAT Technical Ser vice, where the product can be recycled in an appro-
priate waste container.
Note
•If sealant should leak out, leave it to dry. This way you can pull it off like a
piece of foil.•Observe the expiry date stated on the sealing compound can. Have the
sealing compound exchanged by a specialised workshop.•Seek professional assistance if the repair of a tyre puncture is not
possible with the sealing compound.
What to do first
Certain steps must be taken before repairing a tyre.– If you have a flat tyre or puncture, park the vehicle as far away from the flow of traffic as possible.
–Apply the handbrake firmly.
– Engage first gear , or put the selector lever to position P.
–All passengers should leave the vehicle. They should wait in a
safe area (for instance behind the roadside crash barrier).
– Check whether a repair is possibl e using the Tyre Mobility System
“General information and safety notes.”
– Unscrew inflation cap from the affected wheel.
– Take the tyre repair kit out of the luggage compartment.
WARNING
Switch on the hazard warning lights and place the warning triangles in
position. This is for your own safety and also warns other road users.
Caution
Take special care if you have to repair a tyre on a slope.
Note
•Please observe legal requirements when doing so.•Remember to replace the sealing compound as soon as possible.
IbizaSC_EN.book Seite 211 Donnerstag, 2. September 2010 6:10 18

If and when213
Safety First
Operating Instructions
Practical Tips
Technical Specifications
The individual electrical circuits are protected by fuses. The fuses are located
behind a cover at the left-hand end of the dash panel. When the steering
wheel is on the right, the fuses are on the right-hand side of the dash panel,
behind a cover.
The electric windows are protected by
circuit breakers. These reset automat-
ically after a few seconds when the overload (caused for example by frozen
windows) has been corrected.
Fuses colour code
WARNING
Never “repair” damaged fuses and never replace them with fuses with a
higher rating. Failure to comply could result in fire. This could also cause
damage to other parts of the electrical system.
Note
•If a newly replaced fuse blows again after a short time, the electrical
system must be checked by a specialised workshop as soon as possible.•If you replace a fuse with higher-rating fuse, you could cause damage to
another location in the electrical system.
•Always keep some spare fuses in the vehicle. These are available from
SEAT dealers.Fuses on left side of dash panelFuses
Colour
Amps
Beige
5
Brown
7.5
Red
10
Blue
15
Ye l l o w
20
Natural (white)
25
Green
30
Number
Consumer
Amps
1
Power steering/Engine operation
7.5
2
Diagnostics/Heater/Autoclimate/Cli-
matronic/Electric anti-dazzle mirror/Naviga-
tor/Air conditioning pressure switch/ Climate
fan/ Kisi/ AFS Control unit/Coming home
relay/Soundaktor
10
3
Petrol engine control unit/Flow meter/Diesel
engine control unit/Relay coils/Engine opera-
tion/Bi-turbo fuel control unit
5
4
ABS/ESP switch (turning sensor)/Light lever
10
5
Reverse light/Heating nozzles
10
6
Instrument panel
5
7
Rear fog light
7.5
8
Va can t
9
Headlight lever
10
10
Headlight lever/Clutch (Petrol)/Brakes (all)
5
11
Airbag control unit
5
12
Automatic gearbox/ Headlight lever
10
13
Exterior mirror control
5
IbizaSC_EN.book Seite 213 Donnerstag, 2. September 2010 6:10 18

If and when215
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Fuses below steering wheel in relay holderPTC fuses
AUX 1 Fuses
AUX 3 Fuses
Fuses in engine compartment above batteryNon-metal fuses
Some of the electrical items listed in the table are only fitted on certain
models or are optional extras.
Please note that the above list contains all data at the time of going to press,
so it is subject to modifications.
56
Rear window wiper
10
57
Dipped beam headlight (right side)
15
58
Dipped beam headlight (left side)
15
Number
Consumer
Amps
1
Supplementary electrical heating using air
40
2
Supplementary electrical heating using air
40
3
Supplementary electrical heating using air
40
Number
Consumer
Amps
1
Dipped headlight (left side)
15
2
Dipped headlight (right side)
15
3
Headlight washer pump
20
Number
Consumer
Amps
1
Tra ile r con trol uni t
15
2
Tra ile r con trol uni t
20
3
Tra ile r con trol uni t
20
Number
Consumer
Amps
Number
Consumer
Amps
1
ABS unit
25
2
Electroblower climate heater/fan
30
3
Climate fan
5
4
ABS unit
10
5
Electronic control unit
5
6
Injection module
30
Fig. 133 Fuses in engine
compartment
IbizaSC_EN.book Seite 215 Donnerstag, 2. September 2010 6:10 18

If and when217
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Double headlight bulbs
Main beam
Side lights
Dipped beam headlights
Side lights
Turn signal
Turn signal bulbs– Raise the bonnet.
– Rotate the bulb holder ⇒fig. 135 to the left and pull.
– Remove the bulb by pressing on the bulb holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Fig. 134 Double head-
lights
AAABACADAE
Fig. 135 Turn signal
AA
IbizaSC_EN.book Seite 217 Donnerstag, 2. September 2010 6:10 18

If and when219
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Main beam and side lights– Raise the bonnet. – Move the loop in the direction of the arrow and remove the
cover ⇒fig. 138 .
– Remove connector ⇒ fig. 139 by pulling outward.
– Extract the bulb and fit the replacement so that it sits correctly into the cut-out on the reflector.
– Installation is done in the reverse order.
Single headlight bulbs
Side lights - Dipped beam/main beam.
Turn signal
Fig. 138 Main beam
headlightsFig. 139 Main beam
headlights
A1
A2
Fig. 140 Single headlight
AAAB
IbizaSC_EN.book Seite 219 Donnerstag, 2. September 2010 6:10 18

If and when221
Safety First
Operating Instructions
Practical Tips
Technical Specifications
– Remove the loop ⇒ page 220, fig. 142 in the direction of the
arrow and remove the cover.
– Remove the connector ⇒page 220, fig. 143 from the bulb.
– Unclip the retainer spring ⇒page 220, fig. 143 pressing
inwards to the right.
– Remove the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out.Side lights – Raise the bonnet.
– Remove the loop ⇒ page 220, fig. 142 in the direction of the
arrow and remove the cover. – Remove the bulb holder
⇒fig. 144 outwards.
– Replace the bulb by pulling it out and inserting the replacement.
– Installation is done in the reverse order.
A1
A2A3
Fig. 144 Side lights
A1
A4
IbizaSC_EN.book Seite 221 Donnerstag, 2. September 2010 6:10 18

If and when223
Safety First
Operating Instructions
Practical Tips
Technical Specifications
– Remove the pilot light, by pulling it outwards.Changing bulbs on tail lights
– Remove the connector from housing ⇒page 222, fig. 147 .
– R e m o v e t h e b u l b h o l d e r, s e p a r a t i n g i t f r o m t h e c a s i n g . To d o t h i s , press tabs in the direction of the arrows ⇒fig. 148.
– Once the bulb holder has been removed, press downwards in the direction of the arrow and at th e same time, turn in the direc-
tion of the arrow ⇒fig. 149 .Side turn signals– Press the turn signal to the left or to the right to remove the bulb.
– Remove the bulb holder from the turn signal.
– Remove the failed bulb and replace with a new bulb.
Fig. 148 Changing bulbs
on tail lightsFig. 149 Changing bulbs
on tail lights
AA
AB
A1
A2
Fig. 150 Side turn
signals
IbizaSC_EN.book Seite 223 Donnerstag, 2. September 2010 6:10 18

If and when225
Safety First
Operating Instructions
Practical Tips
Technical Specifications
– First fit the glass with the fastening tabs over the frame of the
switch. Next press the front part until the two long tabs click on
the support.Additional brake lights*Given the difficulty involved in the replacement of this light it should be done
by the Technical Service.Luggage compartment light*
– Extract the tulip shaped fitting by pressing on the inside edge of this -arrow- using the flat side of a screwdriver ⇒fig. 152 .
– Press the bulb sideways and remove it from its housing
⇒ fig. 153 .Jump-startingJump leads
The jump lead must have a su fficient wire cross section.If the engine fails to start because of a discharged battery, the battery can be
connected to the battery of another vehicle to start the engine.
Fig. 152 Luggage
compartment light
Fig. 153 Luggage
compartment light
IbizaSC_EN.book Seite 225 Donnerstag, 2. September 2010 6:10 18