2010 Seat Exeo lights

Lights and visibility125
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Rear reading lightsThe reading lights are switched on and off with the switches .
Luggage compartment lightingThe light is in the upper part of the luggage compartment. A second light is
provided on the inside, below the loading edge.
The light ⇒fig. 96 switches on automatically when the tailgate is opened.
The luggage compartment light is switched off automatically if the tailgate is
left open for more than about 10 minutes.
Fig. 95 Detail of head-
liner: rear reading lights

Fig. 96 Detailed view of
the top of the luggage
compartment: luggage
compartment lighting
exeo_EN.book Seite 125 Montag, 30. August 2010 4:45 16

Lights and visibility
126VisibilityHeated rear window
=
The rear window heating clears the rear window of condensa-
tion.– Press button to switch the rear window heating on or off
⇒fig. 97 .The heated rear window only works when the ignition is switched on. An indi-
cator lamp on the button lights up when the rear window heater is switched
on.
The heated rear window switches off automatically after about 10 minutes if
the outside temperature is above 0°C. Depending on the outside temperature, the exterior mirrors are also heated
while the heated rear window is turned on.
The exterior mirror heating is not activated in temperatures above approxi-
mately 20°C.
For the sake of the environment
Switch off the heated rear window as soon as the rear window has demisted.
By saving electrical power you can also save fuel.Sun visors
The sun visors can improve visibility and contribute to safety.
Fig. 97 Switch for heated
rear window
=
Fig. 98 Sun visor
exeo_EN.book Seite 126 Montag, 30. August 2010 4:45 16

Lights and visibility127
Safety First
Operating Instructions
Practical Tips
Technical Specifications
The sun visors for the driver and the front passenger can be pulled out of
their mountings in the centre of the vehicle and turned towards the doors
⇒
fig. 98 .
The vanity mirrors in the sun visor have covers. On opening the cover , the
mirror light* located in the headliner is automatically switched on. The light
switches itself off when the cover is closed and when the sun visor is pushed
back up.
A1
A2
exeo_EN.book Seite 127 Montag, 30. August 2010 4:45 16

Lights and visibility
128Sun blind*
Sun blinds are provided for the rear window and the rear side
windows.
Sun blind (rear side windows)
– Pull out the blind and hook it into the hooks at the top of the door
frame ⇒fig. 99 .
Sun blind (rear window)
– Press the switch to extend or retract the electric sun blind for the rear window ⇒fig. 100 .The sun blind for the rear window switches off automatically when it reaches
the end position. It can be made to move in the other direction before it
reaches its end position by briefly pressing the switch a second time. If the
ignition is turned off while the blind is still moving, it continues until it
reaches the end position before switching off.
Note
•An overload cut-out may be triggered if the sun blind for the rear window
is operated repeatedly. There will then be a short delay before the blind can
be operated again.•As the material of the sun blind is less flexible at low temperatures, the
electric actuator is switched off when the temperature in the car is below -5°C.
The sun blind can only be operated when the temperature inside the car rises
above this level.
Fig. 99 Sun blind
extended to cover rear
side windowFig. 100 Switch for elec-
tric sun blind on rear
window
i
exeo_EN.book Seite 128 Montag, 30. August 2010 4:45 16

Lights and visibility129
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Windscreen wipersWindscreen wipers
W
The windscreen wiper lever controls the windscreen wipers
and the automatic wash and wipe.The windscreen wiper lever ⇒fig. 101 has the following settings:
Short wipe
– Move the lever down to position to give the windscreen a short wipe.
Intermittent wipe
 / Rain sensor* (activate)
– Move the lever up to position .
– Move the switch up or down to set the wiper intervals. – In vehicles equipped with a rain sensor*, you can move the
switch up and down to set the sensitivity of the rain sensor.
Slow wipe
– Move the lever up to position .
Continuous wipe
– Move the lever up to position .
Automatic wash and wipe
– Pull the lever towards the steering wheel, , to activate the windscreen washer.
– Release the lever. The washer will stop and the wipers will keep running for approximately 4 seconds.
Deactivating the windscreen wiper
– Pull the lever to basic position .
General notes
The washers and wipers will work only when the ignition is switched on.
If you stop briefly, e.g. at traffic lights, the wiper speed will automatically be
reduced. The rain sensor* will automatically be set to the intermittent wipe
function.
The windscreen washer jets are heated when the ignition is switched on.
The wiper intervals in the intermittent wipe setting are also varied automati-
cally according to the road speed (in addition to the manual delay setting).
When the lights are switched on you should only pull the lever briefly to wash
the windscreen, otherwise the headlight washers* will also be enabled. This
will use an unnecessary amount of fluid from the reservoir.
Fig. 101 Windscreen
wiper lever
A1
A2
AA
AA
A3A4
A5
A0
exeo_EN.book Seite 129 Montag, 30. August 2010 4:45 16

Lights and visibility
130Rain sensor
The rain sensor* will only function in the intermittent wipe position. The inter-
mittent wipe function is enabled automatically when it starts to rain.
If the windscreen wiper lever was in the intermittent wipe position when the
ignition was off, the rain sensor will not activate until you reach a speed of 6
km/h.
Use switch to set the sensitivity of the rain sensor*.
If you have selected a high sensitivity level for the rain sensor the windscreen
wipers will react sooner to any moisture on the windscreen.
The wiper intervals in the intermittent wipe setting are also varied automati-
cally according to the road speed (in addition to the sensitivity setting).
WARNING
•For correct visibility and safe driving, the wiper must be in perfect
condition ⇒page 213. Failure to do so could result in an accident.•The rain sensor* is only intended to assist the driver. The driver is still
obliged to manually operate the windscreen wipers as required depending
on visibility.•Do not use water-repellent coatings on the windscreen. In bad visibility
conditions such as light rain, low sun or when driving at night, these coat-
ings can cause increased dazzle, which is a serious safety hazard. Such
coatings can also cause the wiper blades to make noise.Caution
•In the event of frost, check that the wiper blade has not frozen before acti-
vating the windscreen wipers. Should the windscreen wiper system be
enabled when the blade is frozen, this could damage it or even the wind-
screen wiper system motor.
•Make sure you switch off the windscreen wiper system (lever in position
0) before you use an automatic car wash. This will avoid inadvertent trig-
gering of the wipers and possible damage to the wiper system.Note
•Check that the washer fluid reservoir is full before starting a long journey.
Fill the reservoir ⇒ page 231.•Worn or dirty wiper blades can cause smearing on the glass which can
also impair the effectiveness of the rain sensor*. Check the condition of wind-
screen wiper blades at regular intervals.Headlight washer systemWith the lights switched on, operate the automatic wash and wipe
⇒ page 129, fig. 101 , and keep the lever pulled towards you for
at least 1 second.
AA
Fig. 102 Headlight with
extended washer jet
A5
exeo_EN.book Seite 130 Montag, 30. August 2010 4:45 16

Lights and visibility131
Safety First
Operating Instructions
Practical Tips
Technical Specifications
The headlight washer jets come out of the bumper automatically (under water
pressure)
⇒page 130, fig. 102 .
Clean off dirt (insects, etc.) from the lenses at regular intervals, for instance
when filling the tank.
To ensure that the system works properly in winter, keep the nozzle holders
free of snow and remove any ice with a de-icer spray.
Rear view mirrorsInterior mirror with manual anti-dazzle settingNormal setting
– Point the lever at the bottom of the mirror forwards.
Anti-dazzle setting for the interior mirror
– Point the lever at the bottom of the mirror to the rear.
Interior mirror with automatic anti-dazzle adjustment*
The automatic anti-dazzle function can be switched on and off
as desired.Switching off the anti-dazzle function
– Press button ⇒fig. 103 . Indicator lamp goes off.
Switching on the anti-dazzle function
– Press button ⇒fig. 103 . Indicator lamp turns on.Anti-dazzle function
The anti-dazzle function is activated every time the ignition is switched on.
The green indicator lamp lights up in the mirror housing.
When the anti-dazzle function is enabled, the interior mirror will darken auto-
matically according to the amount of light it receives. The anti-dazzle function
is disabled if:
Fig. 103 Interior mirror
with anti-dazzle setting:
Indicator lamp and on/off
switch
AA
AB
AA
AB
exeo_EN.book Seite 131 Montag, 30. August 2010 4:45 16

Lights and visibility
132•the interior lighting is switched on•reverse gear is engaged
Sensors for automatic headlights*
When the light switch is set to the AUTO position, the dipped beam head-
lights are switched on and off automatically according to the ambient light
level with the aid of the sensors located in the interior mirror ⇒page 116.WARNING
Electrolyte fluid can leak from a broken mirror. This fluid can cause irrita-
tion to the skin, eyes and respiratory organs. Wash thoroughly with clean
water should you come into contact with this fluid. Seek medical assist-
ance if needed!
Caution
Electrolyte fluid leaking from a broken mirror can cause damage to plastic
surfaces. Use a sponge or similar to remove the fluid as soon as possible.
Note
•The interior mirror automatic anti-dazzle function* will only work properly
if the sun blind* for the rear window is retracted and if there are no other
objects preventing light from reaching the mirror.•If you have to stick any type of sticker on the windscreen, do not do so in
front of the sensors. Doing so could prevent the automatic headlight or anti-
dazzle function from working correctly or even from working at all.
Exterior mirrors
The exterior mirrors are adjusted electrically.Adjusting the exterior mirrors
– Turn the adjuster knob to position ⇒fig. 104 (left exterior
mirror) or position (right exterior mirror).
– Move the knob as required to adju st the exterior mirror for a good
view behind you.
Retracting both exterior mirrors
– Turn the knob to position .It is advisable to fold the exterior mirrors, for example when parking or when
driving through narrow spaces.
Fig. 104 Detailed view of
the armrest: Adjuster
knobAL
AR
AA
exeo_EN.book Seite 132 Montag, 30. August 2010 4:45 16