2010 Seat Exeo warning light

Cockpit77
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Red symbols
A red symbol warns of a danger.–Stop the vehicle.
– Switch the engine off.
– Check the fault. Obtain professional assistance if necessary.
The red symbols are used to indicate a Priority 1 fault (serious malfunction).
A red symbol is accompanied by three warning chimes. The symbols will keep
flashing until the faults are corrected. If several Priority 1 faults are detected
at the same time, the symbols are displayed one after the other for about 2
seconds.Fault in the brake system
H
A fault in the brake system should be repaired as soon as
possible.If the symbol
H flashes in the display, there is a fault in the brake
system. One of the following messages will appear in the display
together with the symbol:
Stop vehicle, check brake fluid and hydraulic fluid levels
Warning! Fault in brake system (ABS) Take vehicle to workshop
–Stop the vehicle.
– Check the brake fluid level ⇒page 233.
If the ABS fails, the ABS warning lamp
J will light up together with the brake
system fault symbol
H ⇒ .
WARNING
•Before opening the bonnet and checking the brake fluid level, observe
the warning information in ⇒ page 224, “Work in the engine compart-
ment”.•If the brake fluid level in the reservoir is too low, this could result in an
accident. Do not drive on! Obtain technical assistance.
H
BRAKES
Fault in brake system
⇒ page 77

COOLANT
Coolant level too low / coolant tem-
perature too high
⇒ page 78
E
OIL
PRESSURE
Engine oil pressure too low
⇒ page 78Fig. 54 Display: Coolant
level warning
exeo_EN.book Seite 77 Montag, 30. August 2010 4:45 16

Cockpit
78•If the brake warning lamp lights up together with the ABS warning
lamp, this can mean that there is a fault in the ABS control function. As a
result, the rear wheels can lock relatively easily when braking. Under
certain circumstances, the rear of the vehicle could suddenly sway from
side to side, with the subsequent dang er of skidding. Drive carefully to the
nearest specialised workshop and have the fault repaired.
Fault in the cooling system

Faults in the cooling system must be repaired immediately.If the
 symbol flashes in the display, this means that either the
coolant temperature is too high or the coolant level is too low. The
following message will appear in the display together with the
symbol:
Switch off engine and check coolant level
– Stop the vehicle.
– Switch the engine off.
– Check the coolant level ⇒page 229.
– Add more coolant if necessary ⇒page 229.
– Wait for the symbol to go out before driving on.
– Obtain professional assistance if necessary.
If the coolant level is correct, the overheating may be caused by a malfunction
of the radiator fan. If the alternator warning lamp lights up as well
⇒page 69, it is possible that
the drive belt has broken.
Caution
Do not drive on if the symbol
v has come on to indicate a fault in the cooling
system, otherwise there is a risk of engine damage.
Engine oil pressure too low
E
If the engine oil pressure is too low the fault must be repaired
immediately.If the
E
symbol flashes in the display, the oil pressure is too low.
The following message will appear in the display together with the
symbol:
Switch off engine, check oil level
– Stop the vehicle.
– Switch the engine off.
– Check the engine oil level ⇒page 226.
– Obtain professional assistance if necessary.
Engine oil level too low
If the engine oil level is too low, add more oil ⇒page 227.
Engine oil level correct
If the
E symbol flashes and the engine oil level is correct, obtain profes-
sional assistance. Do not drive on! Do not continue to run the engine, even at
idle speed .
WARNING (continued)
exeo_EN.book Seite 78 Montag, 30. August 2010 4:45 16

Cockpit79
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Note
The oil pressure warning lamp
E is not an indicator for the oil level. The oil
level should therefore be checked regularly, preferably every time you fill the
tank.
Ye ll o w s y m b o l s
A yellow symbol indicates a warning.
Yellow symbols are used to indicate a Priority 2 fault (warning).

Brake light failure warning light
⇒ page 80

Fuel level low
⇒page 80
X
Engine speed governing
⇒page 80F i g . 5 5 D i s p l a y : F u e l l e v e l
low

Check engine oil level
⇒page 80

Engine oil sensor faulty*
⇒page 80

Diesel particulate filter* obstructed
⇒page 80

Photosensor/rain sensor faulty
⇒page 81
I
Brake pad worn
⇒page 81

Speed warning 1
⇒page 81

Dynamic headlight range control*
faulty
⇒page 81


Adaptive headlights* faulty
⇒page 81

Washer fluid level low*
⇒page 81

Speed warning 2*
⇒page 81
F
Battery voltage too high or too low*
⇒page 81

Bulb monitor*
⇒page 82
~
Tyre pressure monitoring system*
Loss of pressure
⇒page 89
TPMS
Tyre pressure monitoring system*
System not available
⇒page 66
exeo_EN.book Seite 79 Montag, 30. August 2010 4:45 16

Cockpit
80Yellow symbols are accompanied by one warning buzzer. The function indi-
cated should be checked as soon as possible. If several Priority 2 faults are
detected at the same time, the symbol s are displayed one after the other for
about 2 seconds at a time.Brake light failure

This warning light will appear on the upper part of the display if any of the
brake lights has failed. A text message in the central part of the display indi-
cates which brake light has failed (left or right).Fuel level low

When this symbol
 comes on for the first time, there are about 8 to 10 litres
of fuel left in the tank. You should fill up as soon as possible ⇒page 220.
Engine speed governing
X
Max. engine speed XXXX rpm
There is a fault in the engine management. In addition, the warning lamp
%0#
on the instrument panel will light up. The engine speed will be governed to
the speed displayed in the driver information system. Please ensure that the
engine speed does not exceed the speed shown (for example, when
changing down a gear).
Take the vehicle to a qualified workshop immediately to have the fault
repaired.
Check engine oil level

If the
 symbol lights up, please check the engine oil level as soon as
possible ⇒page 226. Top up the oil at the next opportunity ⇒page 227.
Engine oil sensor defective*

If the

symbol lights up, take the vehicle to a qualified workshop and have
the oil level sensor checked. Until then it is advisable to check the oil level
every time you fill up with fuel ⇒page 226.
Diesel particulate filter obstructed

If the symbol
 lights up, you can contribute towards automatic filter
cleaning by driving in the right manner. To do this, drive about 15 minutes in
4th or 5th gear (automatic gearbox: S gear range) at a speed of 60 km/h, with
the engine running at approximately 2000 rpm. The increase in temperature
will burn off any soot in the filter. When cleaning is successful, the symbol
switches off.
If the symbol  does not turn off, or the three lamps turn on (particulate
filter
, emission control system fault
 and heaters
D), take the vehicle
to a qualified workshop to repair the fault.
For further information on the diesel particulate filter, see ⇒page 194.
WARNING
It is essential that you adjust your speed to suit the weather, road, terrain
and traffic conditions. The recommended driving speed must never lead to
the driver disregarding the traffic regulations.
exeo_EN.book Seite 80 Montag, 30. August 2010 4:45 16

Cockpit81
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Photosensor/rain sensor faulty

 Automatic headlights / automatic wipers faulty
If the  s y m b o l l i g h t s u p , t h i s m e a n s t h a t t h e p h o t o s e n s o r / r a i n s e n s o r i s n o t
working. For safety reasons, the dipped beam headlights will then be
switched on permanently when the light switch is set to the AUTO position.
However, you can still switch the lights on and off in the normal way with the
light switch. If the rain sensor is faulty, the functions operated via the wind-
screen wiper lever will still be available. You should have the photo-
sensor/rain sensor checked by a specialised workshop as soon as
possible.
Worn brake pads
I
If the
I symbol lights up, have the front brake pads (and, for safety reasons,
the rear pads as well) inspected by a qualified workshop.
Speed warning 1

If the
 symbol lights up, this means you are exceeding the speed that has
been pre-set with the speed warning function. You should reduce your speed
accordingly ⇒page 82.
Headlight range control faulty

This symbol
 indicates a malfunction in the dynamic headlight range
control. Take the vehicle to a qualified workshop to have the dynamic head-
light range control function repaired.
Adaptive headlights* faulty



Adaptive headlights faulty
This symbol

indicates that the adaptive headlight system is faulty. Take
the vehicle to a qualified workshop to have the headlights or the adaptive
headlight control unit repaired.
Washer fluid level low

If the
 symbol lights up, top up the fluid for the windscreen washer and
headlight washer system* ⇒page 231.
Speed warning 2

If the
 symbol lights up, this means you are exceeding the speed that has
been pre-set. You should reduce your speed accordingly ⇒page 82.
Battery voltage too high or too low
F
If the
F symbol lights up, take the vehicle to a qualified workshop and have
the following items checked:
•Poly V-belt•Battery condition
I t is a l s o a d v isa b le t o ch e ck w h e t h e r t h e a l te r na t o r wa r n i n g la m p ha s co m e o n
⇒ page 69.
exeo_EN.book Seite 81 Montag, 30. August 2010 4:45 16

Cockpit
82Bulb monitor

The bulb monitor checks whether the lights on the vehicle are
working.If a defective bulb is detected, or if one of the lights has failed for any reason,
the bulb monitor symbol
 will appear in the display together with an addi-
tional message (which goes out after 5 seconds). For instance, if the rear left
turn signal is not working, the display in the instrument panel will show the
following message:
Left rear turn signal
The message disappears after 5 seconds. Press the CHECK button briefly if
you wish to call up the message again.
If the display indicates that one of the lights is not working, this can have a
number of causes:
•Bulb failure ⇒page 260.•A blown fuse ⇒page 258, “Changing fuses”.•Faulty electrical wiring.
It is not necessary to have lamps replaced in a specialised workshop,
however the use of Xenon lamps is recommended.
LED lamps
If any of the LED (Light Emitting Diode) functions fail, the complete lamp
should be replaced.
The failure of the lamp is only shown when the LED function goes out
completely. Sometimes, a LED will stop working, without displaying the
warning as the function continues to operate.
WARNING
•Bulbs are highly sensitive to pressure. The glass can break when you
touch the bulb, causing injury.•The high voltage element of gas discha rge bulbs* (xenon light) must be
handled correctly. Otherwise, there is a risk of death.
Speed warning*

Introduction
The speed warning function can help prevent you exceeding
a particular pre-set maximum speed.The speed warning function will warn the driver if a pre-set maximum speed
is exceeded. The system gives an warning buzzer signal if the set speed is
Fig. 56 Display: Speed
warning function
exeo_EN.book Seite 82 Montag, 30. August 2010 4:45 16

Cockpit83
Safety First
Operating Instructions
Practical Tips
Technical Specifications
e xcee d ed by a b out 10 k m / h. A war ni ng s y m b ol will als o a ppear in t he display
⇒
fig. 56 .
The speed warning function has two different warning speeds, which operate
independently and serve slightly different purposes:
Speed limit warning 1

With speed limit warning 1, the maximum speed can be changed while
driving. The speed limit that has been set remains stored until the ignition is
switched off, or until it is changed or cleared.
The warning symbol
 for speed limit warning 1 ⇒page 82, fig. 56 will
appear in the display if you exceed the pre-set speed. It goes out again if the
speed is reduced below the set speed limit.
The symbol also goes out if the speed is increased to more than about
40 km/h above the set speed for at least 10 seconds. However, this does not
cancel the speed limit that was originally set.
Setting speed limit warning 1 ⇒page 83.
Speed limit warning 2 
With speed limit warning 2, the speed limit can only be changed or cleared
when the ignition is switched off. You are recommended to store this speed
limit warning if you always wish to be reminded of a particular speed limit.
This could be when driving in countries with general speed limits, or if a
particular speed should not be exceeded when winter tyres are fitted etc.
The speed limit warning symbol
 for speed warning 2 will appear in the
display if you exceed the pre-set speed. Unlike speed limit warning 1, the
warning symbol only goes out once the road speed has dropped below the
set value again.
Setting speed limit warning 2 ⇒page 84.
Note
Please bear in mind that, even with the speed warning function, it is still
important to keep a eye on the vehicle’s speed with the speedometer and to
observe the legal speed limits.Setting speed limit warning 1
Use the CHECK button to set speed limit warning 1.Setting the speed limit
– Drive at the desired maximum speed.
– Press the CHECK button and hold it down until the symbol
⇒page 82, fig. 56 appears.
Fig. 57 Detailed view of
the instrument panel:
CHECK button
exeo_EN.book Seite 83 Montag, 30. August 2010 4:45 16

Cockpit
84
Clearing the speed limit
– Drive the vehicle at a minimum of 5 km/h.
– Press the CHECK button for at least two seconds.The speed warning symbol
 lights up briefly in the display when the button
is released to confirm that the selected speed has been stored. The speed
limit that has been selected remains st ored until another speed is selected
with a brief push of the button, or until the memory is cleared with a long
push of the button.
Setting speed limit warning 2
Speed limit warning 2 is set using the switches on the wind-
screen wiper lever.
Setting the speed limit
– Switch the ignition off.
– Briefly press the CHECK button in the instrument panel ⇒page 83, fig. 57 . The odometer and the digital clock will light
up.
– Press the CHECK button for at least two seconds. The display will show the speed limit which is currently set or, if no speed limit
has been set, the cr ossed out warning symbol for speed limit 2.
– To change the speed limit, press the top or bottom of the function selector switch on the windscreen wiper lever ⇒fig. 58 . The
speed limit displayed will then in crease or decrease by 10 km/h
at a time.
Clearing the speed limit
– Switch the ignition off.
– Briefly press the CHECK button in the instrument panel ⇒page 83, fig. 57 . The odometer and the digital clock will light
up.
– Press the CHECK button for at least two seconds. The display will show the speed limit which is currently set.
– Now press and hold the Reset button on the windscreen wiper lever ⇒fig. 58 until the crossed out warning symbol for
speed limit 2 appears on the display.The display lighting for the odometer and digital clock goes off again a few
seconds after the button is released.
Fig. 58 Windscreen wiper
lever: Function selector
switch
AA
AB
exeo_EN.book Seite 84 Montag, 30. August 2010 4:45 16