2010 Seat Alhambra tailgate

Seats and storage compartments 148
Each rear seat can fold down individually to extend the luggage compart-
ment.
Folding the seats in the second row of seats for loading
xIf necessary, open the belt loop and wind up the seat belt by hand.
xIf it is necessary, remove the head rests on the integrated child seats then
reinstalled the integrated child seats Ÿpage 52.
xIf necessary, raise the armrests.
xRemove objects from the footrest area in front of and behind the rear seat
Ÿ.
xMove the rear seat all the way back.
xPush the head restraint down as far as it will go Ÿpage 10.
xIn the middle seat, close the drinks carrier in the rear of the centre
console, if necessary.
xPull lever Ÿpage 147, fig. 95 back and fold the backrest forwards.
The complete rear seat folds forward Ÿ.
xFold the backrest forwards until it locks into the load surface position
Ÿpage 147, fig. 95 .
xIf necessary, pull on the lever Ÿfig. 96 to move the seat to the
required position.
xWhen the seat is folded down, no adults or children should travel in it
Ÿ.
Folding the seats in the third row of seats for loading
xIf necessary, open the belt loop and wind up the seat belt by hand.
xOpen the tailgate.
xPush the head restraint down as far as it will go Ÿpage 10.
xRemove objects from the footrest area in front of and behind the rear seat
Ÿ.
xRemove objects from the space below the rear seat.
xRemove the attachment elements and supports for the net from the rail
system.
xPull lever Ÿfig. 96 back and fold the backrest forwards. The rear seat
folds forward Ÿ and the cushion also moves forward.
xFold the seat tray forward on top of the folded seat.
Fig. 96 Third row of seats: fold down the rear seat to
load then return to position .AAAB
A1
AB
A2
A1

Seats and storage compartments149
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWhen the seat is folded down, no adults or children should travel in it
Ÿ.
Putting the seats in the second row back in place
xPull lever Ÿpage 147, fig. 95 upwards and place the seatback in
vertical position. The entire seat folds backwards.
xPull on the rear seats and the backrest to ensure that they are correctly
locked in place and that the safety belt protection is guaranteed for rear seat
passengers.
Putting the seats in the third row back in place
xOpen the tailgate.
xPull on the handle Ÿpage 148, fig. 96 to put the seat tray back in
position.
xPull on the handle Ÿpage 148, fig. 96 . The entire seat folds back-
wards.
xPress on the seat tray in the backrest until it is held in position by its
magnets.
xOpen the sliding door.
xPut the backrest into position and press firmly until it clicks into place.
xPull on the rear seats and the backrest to ensure that they are correctly
locked in place and that the safety belt protection is guaranteed for rear seat
passengers.
WARNING
Folding and lifting the rear seats carelessly without paying attention could
cause serious injury.
xNever fold or lift the seats while driving.
xDo no trap or damage seat belts when raising the backrest.
xKeep your hands, fingers, feet and other body parts out of the hinges
and the seat locking mechanism when folding and unfolding.
xMats or other objects can be caught in the hinges of the backrests or
rear seat. This could prevent the seat or backrest from locking securely in
the vertical position.
xAll backrests must engage correctly for the seat belts on the rear seats
to work properly. When the backrest of an occupied seat is not correctly
locked in place, the passenger can be thrust forward with the backrest in
case of sudden braking, sudden manoeuvres or an accident.
xNo seat must be occupied if the backrest or seat is folded or not
correctly engaged.
Caution
Before folding the backrest of the rear seat, adjust the front seats so that the
head restraint or backrest do not hit them when it is folded.
Caution
xObjects placed in the footrest area in front of and behind the rear seats
can be damaged when seats are folded down or put back into position.
Remove any objects in the way before folding seats down or repositioning
them.
xObjects placed in the moulding on the back of the third row of seats can
be damaged when folding down the seats or putting them back into position.
Remove any objects in the way before folding seats down or repositioning
them.
xThe attachment elements and supports for the net partition placed on the
rail system can be damaged when folding down seats from the third row or
putting them back into position and these can also damage the seats them-
selves. Before folding down or repositioning the seats, remove the attach-
ment elements and supports for the net from the rail system.
A1
A2
A3
WARNING (continued)

Seats and storage compartments159
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Roof carrier system
Introduction
The vehicle roof has been designed to optimise aerodynamics. For this
reason, conventional roof carrier systems cannot be secured to the roof rails.
Given that the water drains have been incorporated into the roof for aerody-
namic reasons, only the SEAT approved basic supports and roof carrier
systems can be used.
When should the roof carrier system be removed?
xWhen it is not being used.
xWhen the vehicle is being washed in a car wash.
xWhen the vehicle height exceeds the maximum height (for example, in a
garage).
Additional information and warnings:
xLight Ÿpage 113
xTransporting Ÿpage 13
xEcological driving Ÿpage 252
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
The risk of an accident is increased by transporting heavy or bulky loads on
the roof, which affects the car's handling by shifting the centre of gravity
and increasing susceptibility to cross winds.
xAlways secure loads correctly with suitable and undamaged attach-
ment rope or straps.
xLarge, heavy, wide and flat loads negatively affect the vehicle aerody-
namics, centre of gravity and handling.
xAvoid brusque manoeuvres and sudden braking.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
Caution
xAlways remove the roof carrier system from the roof before entering a car
wash.
xThe height of your vehicle is changed by the installation of the roof carrier
and the load secured on it. Compare the vehicle height with the passage
height, for example in underground car parks or entering garage doors.
xThe roof antenna, the range of the panoramic sliding roof and the tailgate
should not be affected by the roof carrier system and the load being trans-
ported.
xTake extra care not to let the tailgate strike the roof load when opening.
For the sake of the environment
The vehicle uses more fuel when the roof carrier system is fitted.
WARNING (continued)

Driving 234
Rear Assist system*
Introduction
The camera fitted to the tailgate helps drivers during parking or reversing
manoeuvres. The camera image and certain orientation points generated by
the system are indicated on the factory-fitted radio or navigation system
screen.
Two types of location point (modes) can be selected:
xMode 1: reverse parking perpendicular to the road (e.g. in a car park).
xMode 2: reverse parking parallel to the curb.
The mode can be changed by pressing the button on the radio or navigation
system screen. Only the mode to which the points can be changed will be
displayed.
Additional information and warnings:
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Use of the camera to calculate the distance from obstacles (people, vehi-
cles, etc.) is inaccurate and may cause accidents and severe injuries.
xThe camera lens expands and distorts the field of vision and displays
the objects on the screen in a different, vague manner.
xSome objects may not be displayed or may not be very clear (e.g. very
thin posts or fences), due to the resolution of the monitor or if the light is
dim.
xThe camera has blind spots in which obstacles and people are not regis-
tered.
xKeep the camera lens clean and clear of snow and ice. Do not cover it.
WARNING
The intelligent technology in the rear assist system cannot change the
limits imposed by the laws of physics and by the system itself. Careless or
uncontrolled use of the rear assist system may result in severe injuries and
accidents. The system is not a replacement for driver awareness.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
xAlways keep a close eye on the area around the vehicle and always look
towards where you are parking. The display shows the path of the rear end
of the vehicle using the current steering angle. The front of the vehicle
turns more in comparison with the rear.
xDo not be distracted from the traffic when looking at the screen.
xAlways observe the area around the vehicle, as the cameras do not
always detect children, animals or objects.
xThe system might not show all areas clearly.
xOnly use the rear assist system when the tailgate is completely closed.
Caution
xThe camera only displays 2D images on the screen. Due to the lack of
depth, it might be difficult or impossible to recognise protruding objects or
cracks in the road.
xThe cameras may not always be able to detect objects such as thin rails,
fences, posts and trees, etc. This could result in damage to your car.

Driving 236
Things to note
Cleaning the camera lens
Keep the camera lens clean and clear of snow and ice:xMoisten the lens using a commercially available, alcohol-based glass
cleaning agent and clean the lens with a dry cloth Ÿ.
xRemove snow using a small brush.
xUse de-icing spray to remove any ice Ÿ.
Caution
xNever use abrasive cleaners to clean the camera lens.
xNever remove snow or ice from the camera lens using warm or hot water.
This could damage the lens.
Note
SEAT recommends that you practise parking with the rear assist system in a
quiet location or in a car park to become familiar with the system, including
the orientation lines and their function.
Note
The orientation lines will not be displayed on the screen if the tailgate is open
or the factory-fitted towing bracket is electrically connected to a trailer.
1) Do not use the rear assist system in the following cases:
– If there is a fault in the dynamic chassis control (DCC).
– If the image displayed is not very clear or reliable (low visibility or dirty
lens).
– If the space behind the vehicle cannot be clearly or completely recog-
nised.
- If the vehicle has been overloaded at the rear.
– If the driver is not familiar with the system.
– If the tailgate is open.
- If the position and installation angle of the camera have been changed,
e.g. in a rear-end collision. Have a specialist workshop check the system.
2) Optical illusions of the camera (examples)
The rear assist camera produces two-dimensional images. Any cracks in or
objects protruding from the ground or from other vehicles are more difficult
to spot or cannot be seen due to a lack of depth in the image displayed.
Objects or other vehicles may seem to be closer or further away than what
they really are:
– On changing from a flat surface to a slope or gradient.
– On changing from a slope or gradient to a flat surface.
- If the vehicle has been overloaded at the rear.
– On approaching protruding objects. These objects may be outside the
angle of vision of the camera when reversing.

Trailer towing261
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xIf the trailer absorbs excessive electric current, the vehicle electronics
may be damaged.
xNever connect the trailer's electric system to the electrical connections of
the rear lights or any other power sources. Only use suitable connections for
providing electric current to the trailer.
Note
Towing a trailer places additional demands on the vehicle. At SEAT, we recom-
mend additional services between the normal inspection intervals if the
vehicle is used frequently for towing a trailer.
Note
In some countries, an additional fire extinguisher is required if the trailer
weight is more than 2500 kg
Electric tow hitch ball
The rotation radius of the tow hitch ball should be free of people, animals and
objects Ÿ.
The tow hitch is located in the bumper. The electric tow ball is fixed and
cannot be removed.
Releasing and unfolding the tow ball
xStop the vehicle and apply the electric parking brake.
xSwitch the engine off.
xOpen the tailgate.
xPress the knob briefly Ÿfig. 163. The tow ball is released electronically
and folds out automatically; the button indicator will blink.
xMove the ball joint until it inserts and the button indicator lights.
xClose the tailgate.
xBefore hitching the trailer, remove the dust guard from the ball.
xThe indicator only lights when the tailgate is open and when a trailer is
not hitched.
Restoring the tow ball to its originally position
xStop the vehicle and apply the electric parking brake.
xSwitch the engine off.
xRemove the trailer and disconnect the cable between the vehicle and
trailer. If necessary, remove the socket adapter.
xPlace the dust guard over the ball.
xOpen the tailgate.
xPress the knob briefly Ÿfig. 163. The tow ball is electronically released;
the indicator blinks.
xPush the tow ball into the bumper until it locks in position and the button
indicator lights.
xClose the tailgate.
Fig. 163 Right-hand side
of the luggage compart-
ment: button to electri-
cally release the tow hitch
ball.

Trailer towing 262
The warning lamp
xWhen the indicator flashes, the tow ball is not in its final position, has not
engaged or is damaged Ÿ.
xWhen the indicator remains lit and the tailgate is open, the tow ball has
inserted correctly into the folded or deployed position.
xWhen the tailgate is closed, the indicator is turned off.
WARNING
The incorrect use of the tow hitch can cause accidents and injury.
xEnsure that no person, animal or object gets in the way of the tow ball.
xNever push the button when there is a trailer hitched or when any kind
of carrier or accessory is fitted to the tow hitch ball.
xWhile the ball is moving, do not interfere with any tool.
xDo not drive with a trailer if the indicator does not light.
xIf there is a fault in the electric system or the trailer tow hitch, visit a
specialist workshop to have it checked.
xIf the diameter of the tow hitch is less than 49 mm, never use this for a
trailer.
Caution
xIf anything is attached to the tow hitch ball, do not, under any circum-
stances press the button.
xNever direct a high-pressure or steam cleaning system directly at the tow
hitch ball or trailer power socket. This could cause damage to seals or remove
lubricating grease.
Note
In extremely low temperatures, it is possible that the tow hitch is not
released. In this case, place the vehicle in a warmer location (for example, a
garage).
Installing a bicycle carrier to the tow hitch
The maximum load permitted for a bicycle carrier on the tow hitch ball is 75
kg, with a maximum distance of 300 mm from the support. The distance
between supports is the distance between the bicycle carrier centre of gravity
(with the bicycles) and the centre of point of the tow hitch ball.
WARNING
The incorrect use of the tow hitch with a bicycle carrier installed can cause
accidents and injury.
xNever exceed the load and distances between supports indicated.
xNever fit the bicycle carrier to the tow hitch ball neck, underneath the
tow hitch given that the bicycle carrier may be incorrectly fitted due to the
shape of the tow hitch and the model of bicycle carrier.
xAlways read and take the manufacturer assembly instructions into
account.
Caution
Exceeding the maximum load and distance between supports indicated can
cause considerable damage to the vehicle.
xNever exceed the specifications.
Hitching and connecting the trailer
Trailer cable
Always secure the trailer cable to the towing vehicle correctly. Leave a little bit
of slack in the cable for turning. However, ensure that the cable does not rub
off the ground while driving.

Vehicle maintenance and cleaning271
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWashing the vehicle in low temperatures: When washing the vehicle with
a hose, do not direct water into the lock cylinders or the gaps around the
doors, tailgate, or sunroof. Locks and seals could freeze!
Caution
To prevent damage to the vehicle, please observe the following before
entering an automatic car wash:
xCompare the distance between the vehicle wheels and the distance
between the guide-rails of the car wash to prevent damage to the wheels and
tyres!
xSwitch off the rain sensor and the Auto Hold function before entering a car
wash.
xCompare the height and width of your vehicle with the available height
and width when entering and driving through the car wash.
xFold in exterior mirrors Electrically retractable exterior mirrors must NOT
be folded in or out by hand. Always use the electrical power control.
xTo avoid damaging the bonnet paintwork, rest the wipers on the wind-
screen after drying them. Do not let them fall!
xLock the tailgate to prevent it from opening unexpectedly while inside the
car wash.
Washing the vehicle with high pressure cleaning equipment
When cleaning the vehicle with a high-pressure cleaner, always follow the
operating instructions for the equipment. Pay special attention to the
required pressure of the jet and the distance between the jet and the vehicle
Ÿ.
Keep a suitable distance from soft materials, such as rubber hoses or insu-
lating material, and from the parking distance warning system sensors. The parking distance sensors are fitted in the rear bumpers and, where appli-
cable, in the front bumpers Ÿ.
Do not use a nozzle that sprays the water out in a direct stream or one that
has a rotating jet for forcing off dirt Ÿ.
WARNING
The incorrect use of high pressure cleaning equipment could result in
permanent damage, visible or invisible, to the tyres or other materials. This
could result in serious accident.
xEnsure there is a suitable distance between the nozzle and the tyres.
xNever wash tyres with a concentrated jet or so-called “dirt blasters”.
Even at large spraying distances and short cleaning times, you may
damage the tyres.
WARNING
After the vehicle has been washed, the braking effect will be reduced (and
the braking distance increased) due to moisture (and ice in winter) on the
brakes.
xDry the brakes and remove ice by braking carefully. Ensure that you are
not endangering other road-users or breaking traffic regulations in the
process.
Caution
xThe temperature of the water must not be above +60 °C (+140 °F).
xTo avoid damage to the paintwork, do not wash the vehicle in full sun.
xThe sensors on the bumpers should be kept clean and free of ice at all
times to ensure the parking distance warning system and the parking aid
system operate correctly. When cleaning with pressure hoses and steam
cleaners, the sensors should be sprayed only briefly. A distance of 10 cm
between the sensors and the steam / hose nozzle must be observed.