2010 Seat Alhambra height

Seats and storage compartments135
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Electrical controls on the front seat
The controls are mirrored for the front right-hand seat.
Mechanically and electrically adjusted controls can be combined on the seat.
WARNING
Using the front electric seats in a careless or uncontrolled manner may lead
to severe injuries.
xThe front seats can also be electrically adjusted when the ignition is
switched off. Never leave children or disabled people alone in the vehicle.
xIn the event of an emergency, stop electrical adjustment by pressing
any button.
Caution
So as not the damage the electrical components of the front seats, do not
kneel on the seats or apply specific pressure to one point of the seat or back-
rest.
Note
It may not be possible to electrically adjust the seat if the vehicle battery is
very low.
Fig. 82 Adjusting the
front left seat forwards or
backwards, the height,
the seat angle and the
front seat backrest.
Fig. 83 Adjusting the
lumbar support.
page 135, fig. 82 Press the control in the direction of the arrow:
Move the seat backwards or forwards.
and Raise or lower the seat.
or Adjust the seat angle.
Forwards or
backwards.Adjust the backrest angle.
fig. 83 Press the corresponding area of the switch:
or Adjust the curve of the lumbar support.
or Adjust the height of the lumbar support.
AA
A1
A2A3
A2A3
AB
A1A2
A3A4

Seats and storage compartments143
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Head restraints
Adjusting the head restraints
All seats are equipped with a head restraint.
Adjusting height
xPush the head restraint up or down in the direction of the arrow with the
button pressed Ÿfig. 90 or Ÿfig. 91 Ÿ.
xThe head restraint must engage securely in position. There are three
possible positions on the second row of seats and two possible positions on
the third row of seats.
Correct adjustment of head restraints
Adjust the head restraint so that its upper edge is at the same level as the top
of your head, or as close as possible to the same level as the top of your head
and under no circumstances below eye level. Keep the back of your neck as
close as possible to the head restraint.
Adjusting the head restraint for short people
Lower the head restraint completely, even if your head is below its upper
edge. When the head restraint is at its lowest, it is possible that a small gap
remains between it and the backrest.
Adjusting the head restraint for tall people
Raise the head restraint completely.
WARNING
Travelling with the head restraints removed or improperly adjusted
increases the risk of severe or fatal injuries in the event of accidents and
sudden braking or manoeuvres.
xAlways fit and adjust the head restraint properly whenever a person is
occupying a seat.
xAll occupants must correctly adjust the head restraint according to
their height to reduce the risk of back injuries in the event of an accident.
The upper edge of the head restraint must be as close as possible to the
same level as the top of your head and under no circumstances below eye
level. Keep the back of your neck as close as possible to the head restraint.
Fig. 90 Adjusting the
front head restraints.
Fig. 91 Adjusting the rear
head restraints.
A1A1

Seats and storage compartments159
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Roof carrier system
Introduction
The vehicle roof has been designed to optimise aerodynamics. For this
reason, conventional roof carrier systems cannot be secured to the roof rails.
Given that the water drains have been incorporated into the roof for aerody-
namic reasons, only the SEAT approved basic supports and roof carrier
systems can be used.
When should the roof carrier system be removed?
xWhen it is not being used.
xWhen the vehicle is being washed in a car wash.
xWhen the vehicle height exceeds the maximum height (for example, in a
garage).
Additional information and warnings:
xLight Ÿpage 113
xTransporting Ÿpage 13
xEcological driving Ÿpage 252
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
The risk of an accident is increased by transporting heavy or bulky loads on
the roof, which affects the car's handling by shifting the centre of gravity
and increasing susceptibility to cross winds.
xAlways secure loads correctly with suitable and undamaged attach-
ment rope or straps.
xLarge, heavy, wide and flat loads negatively affect the vehicle aerody-
namics, centre of gravity and handling.
xAvoid brusque manoeuvres and sudden braking.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
Caution
xAlways remove the roof carrier system from the roof before entering a car
wash.
xThe height of your vehicle is changed by the installation of the roof carrier
and the load secured on it. Compare the vehicle height with the passage
height, for example in underground car parks or entering garage doors.
xThe roof antenna, the range of the panoramic sliding roof and the tailgate
should not be affected by the roof carrier system and the load being trans-
ported.
xTake extra care not to let the tailgate strike the roof load when opening.
For the sake of the environment
The vehicle uses more fuel when the roof carrier system is fitted.
WARNING (continued)

Vehicle maintenance and cleaning271
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWashing the vehicle in low temperatures: When washing the vehicle with
a hose, do not direct water into the lock cylinders or the gaps around the
doors, tailgate, or sunroof. Locks and seals could freeze!
Caution
To prevent damage to the vehicle, please observe the following before
entering an automatic car wash:
xCompare the distance between the vehicle wheels and the distance
between the guide-rails of the car wash to prevent damage to the wheels and
tyres!
xSwitch off the rain sensor and the Auto Hold function before entering a car
wash.
xCompare the height and width of your vehicle with the available height
and width when entering and driving through the car wash.
xFold in exterior mirrors Electrically retractable exterior mirrors must NOT
be folded in or out by hand. Always use the electrical power control.
xTo avoid damaging the bonnet paintwork, rest the wipers on the wind-
screen after drying them. Do not let them fall!
xLock the tailgate to prevent it from opening unexpectedly while inside the
car wash.
Washing the vehicle with high pressure cleaning equipment
When cleaning the vehicle with a high-pressure cleaner, always follow the
operating instructions for the equipment. Pay special attention to the
required pressure of the jet and the distance between the jet and the vehicle
Ÿ.
Keep a suitable distance from soft materials, such as rubber hoses or insu-
lating material, and from the parking distance warning system sensors. The parking distance sensors are fitted in the rear bumpers and, where appli-
cable, in the front bumpers Ÿ.
Do not use a nozzle that sprays the water out in a direct stream or one that
has a rotating jet for forcing off dirt Ÿ.
WARNING
The incorrect use of high pressure cleaning equipment could result in
permanent damage, visible or invisible, to the tyres or other materials. This
could result in serious accident.
xEnsure there is a suitable distance between the nozzle and the tyres.
xNever wash tyres with a concentrated jet or so-called “dirt blasters”.
Even at large spraying distances and short cleaning times, you may
damage the tyres.
WARNING
After the vehicle has been washed, the braking effect will be reduced (and
the braking distance increased) due to moisture (and ice in winter) on the
brakes.
xDry the brakes and remove ice by braking carefully. Ensure that you are
not endangering other road-users or breaking traffic regulations in the
process.
Caution
xThe temperature of the water must not be above +60 °C (+140 °F).
xTo avoid damage to the paintwork, do not wash the vehicle in full sun.
xThe sensors on the bumpers should be kept clean and free of ice at all
times to ensure the parking distance warning system and the parking aid
system operate correctly. When cleaning with pressure hoses and steam
cleaners, the sensors should be sprayed only briefly. A distance of 10 cm
between the sensors and the steam / hose nozzle must be observed.

Accessories, parts replacement and modifications287
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a The Technical Service does not accept liability for damage resulting from
technical modifications or repairs performed incorrectly; neither is the SEAT
warranty valid in these cases.
SEAT recommends you have any technical modifications or repairs performed
at a SEAT authorised service and that you use genuine SEAT spare parts
®.
Vehicles with special accessories and equipment
The manufacturers of additional equipment guarantee that the equipment
complies with applicable laws and regulations with respect to the environ-
ment, in particular Directives 2000/53/CE and 2003/11/CE. The first direc-
tive governs the disposal of end-of-life vehicles while the second refers to the
restrictions on the marketing and use of certain dangerous substances and
preparations.
The vehicle owner should keep the documentation for the additional equip-
ment safely and hand it over to the scrap yard at the end of the vehicle's
service life. This ensures that any additional equipment mounted in end-of-
life vehicles is correctly disposed of with respect for the environment.
WARNING
Repairs or modifications which are not performed correctly may result in
damage or errors in the vehicle operation, affecting the efficiency of the
driver assist systems. This could result in serious accident.
xAll repairs and modifications to the vehicle should only be performed
by a qualified workshop.
Repair and faults in the airbag system
When performing repairs and technical modifications, SEAT's directives
must be observed! ŸModifications and repairs to the front bumper, doors, front seats, and repairs
to the roof or chassis should only be carried out in a qualified workshop.
These components may contain parts or sensors belonging to the airbag
system.
If work is carried out on the airbag system or remove and fit parts of the
system when performing other repair work, parts of the airbag system may be
damaged. The consequence may be that, in the event of an accident, the
airbag inflates incorrectly or does not inflate at all.
So that the effectiveness of the airbag is not reduced and that removed parts
do not cause any injuries or environmental pollution, regulations must be
observed. These requirements are known to qualified dealerships.
Modifications to the vehicle suspension may affect the operation of the
airbag system in the event of collision. For example, if wheel and tyre combi-
nations not approved by SEAT are used, or if the vehicle height is lowered, the
suspension is stiffened or the suspension springs, telescopic arms, dampers,
etc., are modified, the results received by the airbag sensors and sent to the
control unit may not be accurate. For example, some modifications to the
suspension could increase the force measured by the sensors and result in
the triggering of the airbag systems in collisions. Under normal conditions,
the measured values would be lower and the airbag would not have been trig-
gered. Other modifications may reduce the forces measured by the sensors
and therefore the airbags are not triggered in situations when they should
have triggered.
WARNING
Repairs or modifications which are not performed correctly may result in
damage or errors in the vehicle operation, affecting the efficiency of the
airbag systems. This could result in serious or fatal accident.
xAll repairs and modifications to the vehicle should only be performed
by a qualified workshop.
xAirbag modules must never be repaired: if damaged, they must be
replaced.

Wheels and tyres333
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Tyre code
Fig. 185 Universal code on tyres.
Radial
Rim diameter code
Load index & speed rating
DOT tyre identification number
Severe snow conditions
Tyre ply composition and materials used
Max. load rating
Treadwear, traction and temperature grades
Max. permissible inflation pressure
Passenger car tyre
Nominal width of tyre in millimetres
Ratio of height to width (aspect ratio)A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
Tyre code (example)Meaning
Make, logotypeManufacturer
Product nameName of tyre assigned by manufacturer.
P215 / 55 R 16Size:
PPassenger vehicle code.
215Nominal width between walls, in mm.
55Height/width ratio in %
RTyre type (R indicates "radial").
16Rim diameter in inches
91 VLoad index Ÿpage 334 and speed rating
Ÿpage 334.
XLReinforced tyres.
M+S or M/SWinter tyres (mud and snow tyres) Ÿpage 331.
SSR or DSST, Eufonia,
RFT, ROF, RSC, ZPSpecific manufacturer codes for run-flat tyres.
RADIAL TUBELESSRadial tyre without inner tube.
E4 ...E-mark certifying tyre complies with international
legislation followed by a number denoting the
country granting the authorisation. The authori-
sation number ( several digits) is shown below.

Technical Data 392
Dimensions and capacities
Caution
xSpecial care should be taken when parking in areas with high kerbs or
fixed barriers. Objects protruding from the ground may damage the bumper
or other parts of the vehicle during manoeuvres.
xSpecial attention is required when driving through entrances, over ramps,
kerbs or other objects. The vehicle underbody, bumpers, mudguards and running gear, and the engine and exhaust system could be damaged as you
drive over these objects.
Dimensions
Length, width4,851 – 4,952 mm1,904 mm
Height at kerb weight1,695 – 1,753 mm
Front and rear projection
Wheelbase2,920 mm
Turning circle
Track widtha)
a)This data will change depending on the type of wheel rim.
FrontRear
1,557 – 1,569 mm1,605 – 1,617 mm
Capacities
Fuel tank70 l. Reserve 8 l.
Windscreen washer fluid container with headlight washer3.5 l/ 6 l
Tyre pressure
Summer-grade tyres:
The correct tyre pressure can be seen on the sticker on the inside of the tank flap.
Winter tyres:
The pressure of these tyres is the same as the summer tyre pressure plus 0.2 bar.

Index 394
Anti-trap function
Electric windows . . . . . . . . . . . . . . . . . . . . . 104
Panorama sliding sunroof . . . . . . . . . . . . . 108
Sunshade . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Armrests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Assist systems
Anti-lock brake system (ABS) . . . . . . . . . . . 216
Auto Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Braking assist . . . . . . . . . . . . . . . . . . . . . . . 217
CCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
Cruise control . . . . . . . . . . . . . . . . . . . . . . . 239
DCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Dynamic chassis control . . . . . . . . . . . . . . . 243
Electronic stability programme (ESP) . . . . 216
Optical parking system . . . . . . . . . . . . . . . . 227
Park Assist . . . . . . . . . . . . . . . . . . . . . . . . . . 229
Park assist . . . . . . . . . . . . . . . . . . . . . . . . . . 226
Park Assist system . . . . . . . . . . . . . . . . . . . 229
Parking sensor system . . . . . . . . . . . . . . . . 226
Rear Assist . . . . . . . . . . . . . . . . . . . . . . . . . . 234
Rear assist system . . . . . . . . . . . . . . . . . . . 234
Start assist . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Start-Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Traction control system (TCS) . . . . . . . . . . . 218
Traction control when accelerating (TCS) . 217
Tyre monitoring indicator . . . . . . . . . . . . . . 248
Assistance systems
Electronic differential lock system (EDS) . . 217
Assisted braking systems . . . . . . . . . . . . . . . . . 216
Auto Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222Automatic belt retainer . . . . . . . . . . . . . . . . . . . . 27
Automatic car wash . . . . . . . . . . . . . . . . . . . . . . 270
Switching Auto Hold off . . . . . . . . . . . . . . . 223
Switching the start assist off . . . . . . . . . . . 223
Automatic consumer disconnection . . . . . . . . 321
Automatic dipped beam control . . . . . . . . . . . 117
Automatic gearbox . . . . . . . . . . . . . . . . . . . . . . 201
Changing gear . . . . . . . . . . . . . . . . . . . . . . . 205
Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
DSG automatic gearbox . . . . . . . . . . . . . . . 207
Ignition key lock . . . . . . . . . . . . . . . . . . . . . 197
Kickdown system . . . . . . . . . . . . . . . . . . . . 207
Launch-Control programme . . . . . . . . . . . . 207
Malfunction . . . . . . . . . . . . . . . . . . . . . . . . . 208
Manually unlocking the gear selection lever . .
352
Please also see "Changing gears" . . . . . . . 201
See "Automatic gearbox" . . . . . . . . . . . . . . 201
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
Auxiliary heater . . . . . . . . . . . . . . . . . . . . . 187, 298
Automatic off . . . . . . . . . . . . . . . . . . . . . . . . 294
Programming . . . . . . . . . . . . . . . . . . . . . . . . 189
Remote control . . . . . . . . . . . . . . . . . . . . . . 188
Remote control range . . . . . . . . . . . . . . . . . 189
Remote control: replacing the battery . . . . 189
Switching off . . . . . . . . . . . . . . . . . . . . . . . . 187
Switching on . . . . . . . . . . . . . . . . . . . . . . . . 187
Things to note . . . . . . . . . . . . . . . . . . . 188, 190
User instructions . . . . . . . . . . . . . . . . . . . . . 190
Auxiliary heater remote control
Replacing the battery . . . . . . . . . . . . . . . . . 189AUX-IN connection . . . . . . . . . . . . . . . . . . . . . . 162
Axle loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
B
BAS
See "Braking assist systems" . . . . . . . . . . 217
Battery
Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Discharging . . . . . . . . . . . . . . . . . . . . . . . . . 346
See Vehicle battery . . . . . . . . . . . . . . . . . . . 318
Battery acid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
Before starting out . . . . . . . . . . . . . . . . . . . . . . . . 7
Belt height adjustment . . . . . . . . . . . . . . . . . . . . 26
Belt tension device . . . . . . . . . . . . . . . . . . . . . . . 27
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Service and disposal . . . . . . . . . . . . . . . . . . 27
Belt tension limiter . . . . . . . . . . . . . . . . . . . . . . . 27
Bicycle carrier
Installing a bicycle carrier . . . . . . . . . . . . . 262
Maximum load . . . . . . . . . . . . . . . . . . . . . . 262
Biodiesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
Bonnet
Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Bottle capacity
Windscreen washer water bottle . . . . . . . . 129
Bottle holders . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Brake servo . . . . . . . . . . . . . . . . . . . . . . . . . 215
Electronic parking brake . . . . . . . . . . . . . . . 212