2010 RENAULT SCENIC relay

PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 183
PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 183V9 MR-372-J84-17B050$611.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
ET072
TRANSITION FROM LPG MODE TO PETROL MODE
IN PROGRESS
COMPLETE
NOTESThere must be no present or stored faults.
Ignition on, engine stopped.
Check that the fuel pump starts when petrol mode is entered.
Check status ET025 Fuel pump changes to ACTIVE.
If the fuel pump does not start, check:
– the fuel pump cut-off relay (see DF024 Fuel pump cut-off relay circuit),
– the petrol computer (see17B, Petrol injection).
This fault is detected by the LPG injection computer.
Repair or replace the faulty components, if necessary.
If the status is still not correct, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
S3000_V4C_ET072/S3000_V54_ET072

PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 184
PETROL INJECTION
Fault finding - Interpretation of statuses
17B
17B - 184V9 MR-372-J84-17B050$611.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
ET073
CONDITIONS FOR SWITCHING TO LPG MODE
AUTHORISED
INHIBITED
IMPORTANT
Before working on an LPG supply circuit component, always refer to the appropriate section of the
Workshop Repair Manual (see17C, LPG Injection, Introduction, Safety advice for all operations).
NOTESThere must be no present or stored faults.
Ignition on, engine stopped.
Variable duration depending on:
–ET100 LPG system ready,
–PR002 Coolant temperature,
–PR103 Air temperature,
–PR113 LPG temperature.
Apply the interpretation of faults DF103 LPG expansion valve solenoid valve and DF007 Main relay circuit.
These faults are detected by the LPG injection computer.
Manipulate the wiring harness between the LPG computer and the petrol computer until a change in status is
noted.
Check the insulation, continuity and ensure the absence of interference resistance on the connections
between:
Petrol computer connectorB, track K3 track A1 of the LPG computer
Petrol computer connectorB, track K4 track A2 of the LPG computer
Repair if necessary.
If the status is still not correct, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
S3000_V4C_ET073/S3000_V54_ET073

PETROL INJECTION
Fault finding - Interpretation of commands
17B
17B - 214
PETROL INJECTION
Fault finding - Interpretation of commands
17B
17B - 214V9 MR-372-J84-17B050$799.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54PETROL INJECTION
Fault finding - Interpretation of commands
AC017
CANISTER BLEED SOLENOID VALVE
NOTESThere must be no present or stored faults.
Check the cleanliness and condition of the fuel vapour absorber bleed solenoid valve connections.
Repair if necessary.
Measure the resistance of the petrol vapour absorber bleed solenoid valve.
Replace the bleed solenoid valve for the fuel vapour absorber if the resistance is not 26Ω ±4Ω at 23 °C.
Check for + 12 V feed on track 1 of the fuel vapour absorber bleed solenoid valve with the ignition on.
If +12V is not present:
– using the Universal bornier, check for continuity on the following connections:
Fuel computer, connectorB, track M2 track 1 of the petrol vapour absorber bleed
solenoid valve
Main relaytrack 1 of the petrol vapour absorber bleed
solenoid valve
Repair if necessary.
Disconnect the battery.
Disconnect the computer. Check the cleanliness and condition of the connections.
Using the Universal bornier, check the insulation and continuity of the following connection:
Petrol computer, connector C, track E1 track 2 of the fuel vapour absorber bleed
solenoid valve
Repair if necessary.
If the fault is still present, replace the solenoid valve.
AFTER REPAIRRepeat the conformity check from the start.
S3000_V4C_AC017/S3000_V54_AC017
MR-372-J84-17B050$799.mif

PETROL INJECTION
Fault finding - Interpretation of commands
17B
17B - 216
PETROL INJECTION
Fault finding - Interpretation of commands
17B
17B - 216V9 MR-372-J84-17B050$799.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
AC079
ACTUATOR STATIC TEST
NOTESThere must be no present or stored faults.
Switch the ignition on and run command AC079 Actuator static test.
If the following actuators are not working, apply the interpretation of the associated fault:
– Fuel pump relay, apply the interpretation of DF085 Fuel pump relay circuit.
– The motorised throttle, apply the interpretation of DF079 Motorised throttle valve servo control.
– The electric coolant pump, apply the interpretation of DF570 Coolant pump relay.
–Upstream O
2 sensor heating, apply the interpretation of DF601 Upstream O2 sensor heating power circuit.
– Downstream O
2 sensor heating, apply the interpretation of DF602 Downstream O2 sensor heating power
circuit.
AFTER REPAIRRepeat the conformity check from the start.
S3000_V4C_AC079/S3000_V54_AC079

PETROL INJECTION
Fault finding - Fault Finding Chart
17B
17B-227
PETROL INJECTION
Fault finding - Fault Finding Chart
17B
17B-227V9 MR-372-J84-17B050$940.mif
S3000 Injection
Program No.: AD
Vdiag No.:4C / 54
ALP 1
CONTINUED 2
VEHICLE CHECK
CONTINUED 2Using the universal bornier, check for insulation and continuity on the following
connection:
Computer, connectorB, track D4 track 5 of the main relay
Repair if necessary.
Using the Universal bornier, check for continuity on the following connection:
Computer, connectorB, track M2 track 1 of the main relay
Repair if necessary.
Check the condition and operation of fuse F6 (10A).
Using the Universal bornier, check for continuity on the following connection:
Computer, connector A, track D1 track 8 of the fuse box
Fuse box track8 track1 of the petrol pump relay
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.