Page 33 of 56
87G - 33
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87G
V6 MR-372-J84-87G000$660_eng.mif
UPC
Vdiag No.: 44
ET009
OIL PRESSURE CONTACT
NOTESCLOSED engine stopped, OPEN engine running.
Check the status and the connection of connectors PEM on the UPC and the oil pressure sensor.
Repair if necessary.
Make sure that the sensor is securely mounted on the engine.
Check the insulation against +12 V and the continuity of the connection between:
UPC connector PEM track 12 Track 1 pressure sensor
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
Page 34 of 56
87G - 34
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87G
V6 MR-372-J84-87G000$660_eng.mif
UPC
Vdiag No.: 44
ET010
CONDITIONS FOR STARTING THE ENGINE SATISFIED
NOTESNo particular instructions.
In the Keyless vehicle function, check that the starting conditions are met.
The UPC participates in the engine start function by managing the switches on the gearbox.
Check the operation of the gearbox switches using statuses ET004 Reverse gear selected and ET005
Manual gearbox gear lever position then run fault finding on UCH start and engine management functions.
If the conditions have been satisfied and the starter does not work, refer to ALP 2.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
Page 35 of 56
87G - 35
ENGINE COMPARTMENT CONNECTION UNIT
87G
V6 MR-372-J84-87G000$726_eng.mif
UPC
Vdiag No.: 44
Fault finding - Interpretation of parameters
PR010
ALTERNATOR CHARGE
NOTESCheck in the configuration readings that the alternator type has been configured
correctly.
When the engine has stopped, the value must be constant and greater than 98 %.
With the engine running, the value varies according to the electricity consumption. The
value must not be constant.
Carry out fault finding on the charging circuit.
Disconnect the 2 track connector from the alternator.
With the ignition on, check the presence of + 12 V on track 2 of the alternator.
With the ignition off, check the presence of a voltage below 6 V on track 2 of the alternator.
Repair if necessary.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
MR-372-J84-87G000$726_eng.mif
Page 36 of 56
87G - 36
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
Without xenon lights AC001
MAIN BEAM HEADLIGHTS
NOTESCheck:
–the status and the connection of fuses 8A and 8B on the UPC,
–the status of the bulbs.
Replace them, if necessary.
Check the status and the connection of connector PPA and the fuses on the UPC.
Repair if necessary.
Check the condition and connection of the headlight connectors.
Repair if necessary.
Check the presence of earth on the connection R9 and then on track 1 of the headlight connector.
Repair if necessary.
Check the presence of +12 V on track 4 of the headlights when these are controlled by command AC001.
If everything is fine, replace the bulbs.
If there is a problem, check the insulation against earth and the continuity between the connections:
UPC connector PPA track 3 Left headlight track 4
UPC connector PPA track 4 Right headlight track 4
Repair if necessary.
If the fault is still present, contact the Techline.
MR-372-J84-87G000$792_eng.mif
Page 37 of 56
87G - 37
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
With xenon lights AC001
(continued)
Check the status and the connection of connector PPA and the fuses on the UPC.
Repair if necessary.
Check the condition and connection of the headlight connectors.
Repair if necessary.
Check the presence of earth on connection R9 then on tracks 4 and 10 of the headlights.
Repair if necessary.
Check the presence of +12 V on track 5 (for Mégane vehicles) or on track 4 (for Scénic type vehicles) for the
headlights when controlled by command AC001.
If everything is fine, run the fault finding procedure (see 80C, Discharge bulbs).
If there is a problem, check the insulation against earth and the continuity of the connections:
UPC connector PPA track 3 Track 5 or track 4 (depending on vehicle type) for the left-hand
headlight
UPC connector PPA track 4 Track 5 or track 4 (depending on vehicle type) right-hand
headlight
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
Page 38 of 56
87G - 38
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
Without xenon lights AC002
DIPPED BEAM HEADLIGHTS
NOTESCheck:
–the status and the connection of fuses 8C and 8D on the UPC,
–the status of the bulbs.
Replace them, if necessary.
Check the status and connection of connector PPA and the fuses on the UPC.
Repair if necessary.
Check the condition and connection of the headlight connectors.
Repair if necessary.
Check the presence of earth on connection R9 then on track 1 of the headlight connector.
Repair if necessary.
Check the presence of +12 V on track 2 of the headlights when controlled by command AC002.
If everything is find, replace the bulb or bulbs.
If there is a fault, check the insulation against earth and the continuity of the connections:
UPC connector PPA track 6 Left headlight track 2
UPC connector PPA track 5 Right headlight track 2
Repair if necessary.
If the fault is still present, contact the Techline.
Page 39 of 56
87G - 39
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
With xenon lights AC002
(continued)
Check the status and the connection for connector PPA and the fuses on the UPC.
Repair if necessary.
Check the condition and connection of the headlight connectors.
Repair if necessary.
Check for the presence of earth on connection R9 then on tracks 4 and 10 of the headlight connectors.
Repair if necessary.
Check that there is a +12 V supply on track 3 of the headlights when controlled by command AC002.
If everything is fine, apply the fault finding procedure (see 80C, Discharge bulbs).
If there is a fault, check the insulation against earth is in place and continuity on the connections:
UPC connector PPA track 6 Left headlight track 3
UPC connector PPA track 5 Right headlight track 3
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
Page 40 of 56
87G - 40
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
Without xenon lights AC003
SIDE LIGHTS
NOTESCheck:
–the status and connection of fuses 7A and 7B on the UPC,
–the status of the bulbs.
Replace them, if necessary.
Check the condition and connection of connectors PPA and PPH2 and the fuses in the Protection and
Switching Unit.
Repair if necessary.
Check the condition and connection of the headlights and rear lights.
Repair if necessary.
Check for the presence of earth on connection R9 then on track 1 of the headlights and on track 2 of the rear
lights and the vehicle number plate lights.
Repair if necessary.
Check that there is a +12 V supply on track 5 of the headlights and track 1 of the rear lights and the number
plate when controlled by command AC003.
If everything is fine, replace the bulb or bulbs.
If there is a fault, check the insulation against earth and continuity of the connections:
UPC connector PPH2 track 6 Left rear light track 1
UPC connector PPH2 track 7 Track 1 right-hand rear light and number plate lights
UPC connector PPA track 1 Left headlight track 5
UPC connector PPA track 2 Right headlight track 5
Repair if necessary.
If the fault is still present, contact the Techline.
