2010 RENAULT SCENIC engine

13B-165
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET704
ET705BRAKE SWITCH NO. 1BRAKE SWITCH NO. 2
STATUS DEFINITIONACTIVE: This status indicates that the brake pedal is depressed.
INACTIVE: This status indicates that the brake pedal is released.
Note:
Statuses ET704 and ET705 should change status at the same time. In the event of inconsistency, refer to the
interpretation of fault DF050 Brake switch circuit.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVE
OR
INACTIVEIf the brake lights are working, check the continuity and the absence of interference
resistance between the following connections:
–5A between components 160 and 120,
–BPT between components 160 and 645 (for Mégane II, Scénic II, Modus and Clio III),
–BPT2 between components 160 and 645 (for Kangoo 2),
–AP10 between components 160 and 1016 (for New Twingo),
–65A between components 160 and 645 (vehicle without ESP),
–65G between components 160 and 645 (vehicle with ESP).
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the brake lights are not operational, check:
–the condition and fitting of the brake switch,
–the condition and conformity of the brake lights fuse,
the conformity of the values in the following table:
DCM1.2_V48_ET704/DCM1.2_V4C_ET704/DCM1.2_V50_ET704/DCM1.2_V54_ET704/DCM1.2_V58_ET704/DCM1.2_V5C_ET704/
DCM1.2_V48_ET705/DCM1.2_V4C_ET705/DCM1.2_V50_ET705/DCM1.2_V54_ET705/DCM1.2_V58_ET705/DCM1.2_V5C_ET705

13B-167
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 54
ET741OPTIONAL VEHICLE SPEED RESTRICTION
STATUS DEFINITIONACTIVE: This status indicates that the optional speed limiting function is active.
INACTIVE: This status indicates that the optional speed limiting function is inactive.
NOTESSpecial note:
This status indicates whether the vehicle speed restriction is a customer option, using
command SC040 Speed limiter.
This status is valid only on Kangoo 2
Conformity check: Engine stopped, ignition on or engine running.
"ACTIVE"Vehicle speed restricted using command SC040 Speed limiter. See the interpretation
of parameter PR879 Maximum speed authorized to find the configured speed
restriction.
"INACTIVE"The vehicle has no optional speed restriction.
DCM1.2_V54_ET741

13B-168
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 54
*VU: Commercial vehicle
ET800FAST IDLE SPEED FUNCTION
STATUS DEFINITIONACTIVE: This status indicates that the fast idle speed function is active.
INACTIVE: This status indicates that the fast idle speed function is inactive.
NOTESSpecial note:
This status indicates if the fast idle speed function is activated after use of the command
SC041 Changing commercial vehicle idle speed.
This status is valid only on Kangoo 2.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVEIs the fast idle speed function active? See the interpretation of parameter PR878 Fast
idle speed to find the configured idle speed.
INACTIVEThe fast idle speed function is inactive.
DCM1.2_V54_ET800

13B-169V10 MR-372-J84-13B100$160.mif
13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
Tool parameterDiagnostic tool title
PR005EGR valve opening setpoint
PR008Rail reference pressure
PR010Idle speed regulation setpoint
PR017Fuel flow
PR030Accelerator pedal position
PR032Inlet pressure
PR035Atmospheric pressure
PR037Refrigerant pressure
PR038Rail pressure
PR051EGR valve position feedback
PR055Engine speed
PR059Inlet air temperature
PR063Fuel temperature
PR064Coolant temperature
PR074Battery voltage
PR077EGR valve position sensor voltage
PR078Inlet pressure sensor voltage
PR080Rail pressure sensor voltage
PR086Pedal potentiometer voltage gang 1
PR088Pedal potentiometer gang 2 voltage
PR089Vehicle speed
PR125Power consumed by the air conditioning compressor
PR130Cruise control setpoint
PR132Air flow
PR147Pedal potentiometer voltage gang 1
PR148Pedal potentiometer voltage gang 2
PR568Pedal position gang 1
PR569Pedal position gang 2
DIESEL INJECTION
Fault finding – Parameter summary table

13B-170V10 MR-372-J84-13B100$160.mif
DIESEL INJECTION
Fault finding – Parameter summary table13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
PR730Air flow sensor temperature
PR873Oil oxidation signal
PR878Increased idle speed
PR879Maximum authorised speed
PR932Rate of engine oil dilution
PR1015Oil service interval
Tool parameterDiagnostic tool title

13B-171
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault
memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$170.mif
13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
PR005EGR VALVE OPENING VALUE REQUIRED
PARAMETER
DEFINITIONThis parameter indicates a theoretical opening value for the EGR valve giving optimum
engine performance.
Conformity check with engine stopped and ignition on
The EGR valve theoretical opening value for operation with the engine stopped and ignition on is:
- 10% < PR005 < 0%
Conformity check: Engine running, engine coolant temperature > 80
°C
The EGR valve theoretical opening value for operation with the engine running and the engine coolant
temperature > 80
°C is:
10% < PR005 < 40%
DCM1.2_V48_PR005/DCM1.2_V4C_PR005/DCM1.2_V50_PR005/DCM1.2_V54_PR005/DCM1.2_V58_PR005/DCM1.2_V5C_PR005
DIESEL INJECTION
Fault finding – Interpretation of parameters

13B-172
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault
memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$170.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
PR008RAIL REFERENCE PRESSURES
PARAMETER
DEFINITIONThis parameter indicates the theoretical rail pressure value for optimum engine
operation in bar.
Conformity check: Engine stopped and ignition on, or engine running and engine coolant
temperature > 80
°C
The theoretical rail pressure value is a setpoint of:
200 bar < PR008 < 400 bar
DCM1.2_V48_PR008/DCM1.2_V4C_PR008/DCM1.2_V50_PR008/DCM1.2_V54_PR008/DCM1.2_V58_PR008/DCM1.2_V5C_PR008

13B-173
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault
memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$170.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
PR010IDLE SPEED REGULATION SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the speed of rotation setpoint before last engine stop in rpm.
Conformity check: Engine stopped and ignition on, or engine running and engine coolant
temperature > 80
°C
At idle speed, the engine rotation speed must be between:
700 rpm < PR010 < 1300 rpm.
In the event of a fault, consult the interpretation of faults DF053 Rail pressure regulation function, DF007 Rail
pressure sensor circuit and DF024 Low pressure actuator control circuit.
DCM1.2_V48_PR010/DCM1.2_V4C_PR010/DCM1.2_V50_PR010/DCM1.2_V54_PR010/DCM1.2_V58_PR010/DCM1.2_V5C_PR010