2010 RENAULT SCENIC key

62A - 3
AIR CONDITIONING
Fault finding - Introduction62A
V4
Manual air conditioning
and
Climate control162AAIR CONDITIONING
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault Finding Procedures (this document and the Technical Notes for the injection fitted to the
vehicle, the UCH and the Protection and Switching Unit:
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper version.
Type of diagnostic tools
–CLIP
Special tooling required
3. RECAP
Procedure
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed).
Proceed as follows:
–Renault card in the card reader (keyless vehicle scenario 1, entry level, not hands-free and scenario 2, top of the
range, hands-free)
–press and hold the Start button (longer than 5 seconds) with start-up conditions not fulfilled,
–connect the diagnostic tool and perform the desired operations.
To cut off + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–check that the + after ignition feed has been cut off by checking that the computer warning lights on the instrument
panel have gone out. Vehicle: Scenic II
Function concerned: air conditioning
SPECIAL TOOLING REQUIRED
Multimeter
Elé. 1681Universal bornier
Note:
The left-hand and right-hand xenon bulb computers are powered when the dipped beam headlights light up. Fault
finding procedures can only be carried out on them after the ignition has been switched on in fault finding mode
(forced + after ignition feed) and the dipped headlights are on.
CLIM X84 1.1
Edition 2
MR-372-J84-62A000$020.mif

62A - 10
AIR CONDITIONING
Fault finding - Mode of operation62A
V4MR-372-J84-62A000$010.mif
Manual air conditioning
and
Climate control
CLIM X84 1.1
Edition 2
Summary of components controlled or managed by the climate control computer
Ventilation and climate control unit
Passenger
compartment
blower
Vehicle multiplex
network
Passenger
compart-
ment blower
power
module
Recir-
culation
motorDistribution
motorMixing
motorInterior
temperature
sensor Solar radiation
sensor
Actuator control Sensor management
Climate control computer (control panel)
Climate control
management
(hot and cold)User requests
management
(buttons pressed) Button lighting
Key:
Wire connections =
Multiplex connections =
MR-372-J84-62A000$040.mif

62A - 11
AIR CONDITIONING
Fault finding - Mode of operation62A
V4MR-372-J84-62A000$010.mif
Manual air conditioning
and
Climate control
Summary of components controlled or managed by the manual air conditioning computer
Ventilation and climate control unit
Passenger
compartment
blower
Resistor
unitRecircu-
lation flapDistribution
flapMixing
flap
Vehicle multiplex
network
Actuator control
Manual air conditioning computer
(control panel)
Button lights
(air conditioning button
and heated rear screen
button)Passenger
compartment blower
operation signal
(running or stopped)User request
management
(air conditioning button
and heated rear screen
button pressed)
UCH
Transmission of requests
(air conditioning, heated
rear screen)
Key:
Wire connections =
Multiplex connections =
Mechanical connections =
(cable controls)
CLIM X84 1.1
Edition 2
MR-372-J84-62A000$040.mif

62A - 12
AIR CONDITIONING
Fault finding - Mode of operation62A
V4MR-372-J84-62A000$010.mif
Manual air conditioning
and
Climate control
Block diagram of components controlled or managed by the control panel of heater
versions without air conditioning
Ventilation unit
Passenger
compartment
blower
Resistor
unitRecircu-
lation flapDistribution
flapMixing
flap
Vehicle multiplex
network
Actuator control
user control panel
Button lights (heated rear
screen button)Passenger
compartment blower
operation signal
(running or stopped)User request
management (heated
rear screen button
pressed)
UCH
Transmission of the request
to switch on the heated rear
screen
Key:
Wire connections =
Multiplex connections =
Mechanical connections =
(cable controls)
CLIM X84 1.1
Edition 2
MR-372-J84-62A000$040.mif

62A - 13
AIR CONDITIONING
Fault finding - Mode of operation62A
V4MR-372-J84-62A000$010.mif
Summary of components controlled or managed by the UCH
Summary of components controlled or managed by the Protection and Switching Unit
Passenger
compartment
heating
resistors (RCH)
relay No. 2 Passenger
compartment
heating
resistors (RCH)
relay No. 1 Passenger compartment
heating resistors (RCH)
relay No. 3 (Scénic only)Exterior
temperature
sensor
Vehicle
multiplex
network
Actuator control Sensor management
UCH
Air conditioning request
managementHeated rear screen
control
managementPassenger compart-
ment heating resistor
control management
Engine cooling
fan unitHeated rear
screen and
heated door
mirrorsClimate control
compressorAlternator:
"DF"
terminal
Actuator control Electrical availability management
UPC
"DF" terminal signal formatting
(alternator charge)
Key:
Wire connections =
Multiplex connections =
Manual air conditioning
and
Climate control
CLIM X84 1.1
Edition 2
MR-372-J84-62A000$040.mif

62A - 14
AIR CONDITIONING
Fault finding - Mode of operation62A
V4MR-372-J84-62A000$010.mif
Manual air conditioning
and
Climate control
Summary of components controlled or managed by the injection computer
Refrigerant fluid
pressure sensorEngine coolant
temperature
sensorVehicle
multiplex
network
Sensor management
Engine injection computer
Management of the cold loop (refrigerant fluid pressure,
switch on engine cooling fan request, compressor
engagement authorisation, etc.)Passenger compartment
heating resistors (RCH)
authorised power
management
Key:
Wire connections =
Multiplex connections =
CLIM X84 1.1
Edition 2
MR-372-J84-62A000$040.mif

62A - 15
AIR CONDITIONING
Fault finding - Mode of operation62A
V4MR-372-J84-62A000$010.mif
Manual air conditioning
and
Climate control
Compressor control flowchart
ET143 Air
conditioning request 1
(climate control)Climate control panelET029 Air
conditioning button
(manual air
conditioning)
ET030 Air
conditioning request 2UCH
ET088 Compressor
engagement requestInjection computer
ET004 Air conditioning
authorisation
UPC
(Power and Switching Unit)
Control via wire
connection
Special notes:
This flowchart shows the path of the
compressor engagement request.
Components which may block this request
are not listed (passenger compartment
blower operation signal for the UCH on
manual air conditioning version, correct
refrigerant fluid pressure for the injection,
etc.).
If the compressor does not engage (one of
the requests not transmitted): carry out a
conformity check. Climate
control
compressor
Key:
Multiplex signals.
Wire connections.
CLIM X84 1.1
Edition 2
MR-372-J84-62A000$040.mif