2010 PEUGEOT 5008 spare wheel

124
TYRE UNDER-INFLATION DETECTION
System which automatically checks the
pressure of the tyres while driving. All repairs and changing of
tyres on a wheel fi tted with this
system must be carried out by
a PEUGEOT dealer.
If, when changing a tyre, you install
a wheel which is not detected by
your vehicle (example: fi tting of snow
tyres), you must have the system
reinitialised by a PEUGEOT dealer.
This system does not eliminate
the need to have the tyre pres-
sure checked regularly (refer
to the "Identifi cation markings" para-
graph) to ensure that the optimum
dynamic performance of the vehicle
is maintained and prevent premature
wear of the tyres, particularly in ardu-
ous driving conditions (heavy load,
high speed).
The tyre pressures must be checked
cold, at least once a month. Re-
member to check the pressure of the
spare wheel.
The tyre under-infl ation detection
system may experience temporary
interference due to radioelectric
emissions on a frequency close to
that used by the system.
Sensors fi tted in each valve trigger a
warning in the event of malfunction
(speed above 12 mph (20 km/h)).
The spare wheel is not fi tted with a sensor.
This warning lamp is displayed on the
instrument panel and/or a message
appears on the multifunction screen,
accompanied by an audible signal, to
locate the wheel concerned.

 Check the tyre pressures as soon
as possible.
This check must be carried out when
the tyres are cold.
Under-infl ated tyre The
STOP warning lamp
comes on, accompanied by
an audible signal and a mes-
sage on the multifunction
screen locating the wheel
concerned.

 Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.

 Change the damaged wheel (punc-
tured or very defl ated tyre), and
have the tyre pressure checked as
soon as possible.
Puncture
The tyre under-infl ation detec-
tion system is an aid to driving
which does not replace the
need for the driver to be vigilant or to
drive responsibly. Sensor(s) not detected or faulty
A message appears on the multifunc-
tion screen, accompanied by an audible
signal, to locate the wheel or wheels
which are not detected or to indicate a
fault in the system.
Contact a PEUGEOT dealer to replace
the faulty sensor(s).
This message is also dis-
played when one of the wheels
is away from the vehicle (be-
ing repaired) or when one or more
wheels without a sensor are fi tted.

PRACTICAL INFORMATION
175
CHANGING A WHEEL
The tools 2 to 4 are installed in a box,
in the middle of the spare wheel, placed
underneath the vehicle.
The tools 1 and 6 to 9 are installed
under the concertina boards, in the boot
inner trim.
To gain access to them:

 open the boot,

 raise the concertina boards,
Access to the tools
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.
All of these tools are specifi c to your
vehicle. Do not use them for other
purposes.
List of tools

1. Wheelbrace.
For removing the wheel trim and the wheel fi xing bolts.

2. Jack with integral handle.
For raising the vehicle.

3. "Bolt cover" tool (according to
equipment).
For removing the bolt protectors (covers) on alloy wheels.

4. Centring guide.
For refi tting an alloy wheel to the hub.

5. Socket for the security bolts
(located in the glove box).
For adaptating the wheelbrace to the special security bolts.

6. Two chocks to immobilise the
vehicle.

7. Wheelbrace extension.
For unscrewing/tightening the spare wheel carrier drive.

PRACTICAL INFORMATION
177
Access to the spare wheel
The spare wheel is supported by a cable-
driven carrier underneath the vehicle. Taking out the wheel

 Raise the concertina board to reveal
the spare wheel carrier drive.

 Unscrew the drive fully, using the
wheelbrace 1 and the extension 7 ,
to unwind the carrier cable.

 Detach the wheel/box assembly
from the rear of the vehicle.

 Remove the hook with its connection
plate to release the wheel/box as-
sembly, as shown in the illustration.

 Pull out the wheel to gain access to
the box.

 Slide the box cover to the centre
and remove it to gain access to the
other tools.

PRACTICAL INFORMATION
Tyre under-infl ation
detection
The spare wheel is not fi tted with a
sensor. The punctured wheel must
be repaired by a PEUGEOT dealer. Putting the wheel back in place

 Store the tools used in the box and
close the cover.

 Position the box on the ground and
centre the spare wheel on it.

 Pass the hook with its connection
plate into the wheel then the box, as
illustrated.

 Raise the wheel/box assembly un-
derneath the vehicle by tightening
the carrier drive using the wheel-
brace 1 and the extension 7 .

 Tighten fully and check that the
wheel is horizontally fl ush against
the fl oor.

PRACTICAL INFORMATION
Parking the vehicle
Immobilise the vehicle where
it does not block traffi c: the
ground must be level, stable and
non-slippery ground.
Apply the parking brake unless it
has been programmed to automatic
mode, switch off the ignition and en-
gage fi rst gear * to lock the wheels.
Check that the braking warning lamp
and the P warning lamp on the parking
brake control come on.
If necessary, place a chock under the
wheel diagonally opposite the wheel
to be changed.
The occupants must get out of the
vehicle and wait where they are
safe.
Never go underneath a vehicle raised
using a jack; use an axle stand.
Removing a wheel
List of operations

 Remove the chromed bolt cover
from each of the bolts using the
tool 3 (according to equipment).

 Fit the security socket 5 on the
wheelbrace 1 to slacken the security
bolt.

 Slacken the other bolts using the
wheelbrace 1 only.

 Place the jack 2 in contact with one
of the two front A or rear B locations
provided on the underbody, which-
ever is closest to the wheel to be
changed.

 Extend the jack 2 until its base plate
is in contact with the ground. Ensure
that the centreline of the jack base
plate is directly below the location A
or B used.

 Raise the vehicle until there is suf-
fi cient space between the wheel and
the ground to admit the spare (not
punctured) wheel easily.

 Remove the bolts and store them in
a clean place.

 Remove the wheel.
* position R for the electronic gear
control manual gearbox; P for the
automatic gearbox.

PRACTICAL INFORMATION
180
After changing a wheel
To store the punctured wheel in the boot
correctly, fi rst remove the central cover.
When using the "space-saver" type
spare wheel, do not exceed 50 mph
(80 km/h).
Have the tightening of the bolts and the
pressure of the spare wheel checked
by a PEUGEOT dealer without delay.
Have the punctured wheel repaired
and replace it on the vehicle as soon as
possible.
Fitting a wheel
List of operations

 Put the wheel in place on the hub
using the centring guide 4 .

 Screw in the bolts by hand to the
stop.

 Pre-tighten the security bolt us-
ing the wheelbrace 1 fi tted with the
security socket 5 .

 Pre-tighten the other bolts using the
wheelbrace 1 only.

 Lower the vehicle fully.

 Fold the jack 2 and detach it.

 Tighten the security bolt using the
wheelbrace 1 fi tted with the security
socket 5 .

 Tighten the other bolts using the
wheelbrace 1 only.

 Refi t the chromed bolt covers on
each of the bolts (according to
equipment).

 Store the tools in the box.
Fitting the "space-saver"
spare wheel
If your vehicle is fi tted with al-
loy wheels, when tightening the bolts
on fi tting it is normal to notice that the
washers do not come into contact
with the "space-saver" spare wheel.
The wheel is secured by the conical
contact of each bolt.

PRACTICAL INFORMATION
200
The fi tting of electrical equip-
ment or accessories which
are not recommended by
PEUGEOT may result in a failure of
your vehicle's electronic system.
Please note this specifi c warning.
You are advised to contact a repre-
sentative of the Marque to be shown
the range of recommended equip-
ment and accessories. Depending on the country in
which the vehicle is sold, it
is compulsory to have a high
visibility jacket, warning triangle and
spare bulbs available in the vehicle.
"Styling": "Universal":
You can obtain "Van" conversion kits to
convert a private vehicle into a van.
seat covers compatible with
lateral airbags, leather gear
lever knob, foglamps, door de-
fl ectors, spoiler, styling strips,
alloy wheels, trims, chrome-
plated door handle shells. screenwash, interior and exte-
rior maintenance and cleaning
products.
"In-car technology":
audio systems, amplifi ers, satel-
lite navigation systems, Bluetooth
hands-free system, CD changer,
speakers, DVD player, USB Box,
front and rear parking sensors,
additional Bluetooth wireless
headphones, Bluetooth audio
headphones mains charger.
Installation of
radiocommunication
transmitters
It is advisable to contact a representa-
tive of the PEUGEOT marque before
installing accessory radiocommunica-
tion transmitters with an external aerial
on your vehicle.
The PEUGEOT network will provide
you with the specifi cations (frequen-
cy band, maximum output power,
aerial position, special installation
conditions) of the transmitters which
can be fi tted, in accordance with the
Vehicle Electromagnetic Compatibility
Directive (2004/104/CE).
"Touring":
mats * , boot tray, luggage net,
fi xed coat hook on head re-
straint, stainless steel or carbon
door sills.
For leisure pursuits: roof bars, bicycle
carrier on towbar, bicycle carrier on roof
bars, ski carrier, roof box, booster seats
and child seats, side blinds, under shelf
storage.
Trailer towbar which must be fi tted by
the PEUGEOT network.
* To avoid any risk of jamming of the pedals:
- ensure that the mat is positioned and secured correctly,
- never fi t one mat on top of another.