2010 Peugeot 407 Dag change time
[x] Cancel search: change timePage 29 of 249
1
29
Range (miles or km)
Current fuel consumption(l/100 or km/l or mpg)
This is the average quantity of fuel con-
sumed during the last few seconds.
This shows the distance that can still
be covered with the fuel remaining in
the tank in accordance with the ave-
rage consumption over the last few
miles (kilometres).
Distance remaining to be travelled (miles or km)
Average speed (mphor km/h)
TRIP menu
Press the
"MENU" button for access
to the main menu.
Select the "Trip computer" or "Ve-
hicle diagnostics" application using
t h e n a v i g a t o r , t h e n c o n fi r m o r p r e s s
the "MODE" button until you gain ac-
cess to the trip computer screen, then
c o n fi r m "OK" .
The "Trip computer" or "Vehicle diag-
nostics" menu offers various options:
- Alerts log,
- Status of the functions,
- Inputting the distance to be tra- velled.
Average fuel consumption(l/100 or km/l or mpg)
Distance travelled (miles or km)
Alerts log
This summarises the active warning
messages, displaying them on the
multifunction screen in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Distance remaining (miles or km)
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled.
T h i s fi g u r e m a y i n c r e a s e i f
there is a change in the style
of driving or the road surface,
p r o d u c i n g a s i g n i fi c a n t d r o p i n
current fuel consumption.
When the range is less than 20 miles
(30 km), four bars are displayed. After
fi l l i n g w i t h f u e l , t h e r a n g e i s d i s p l a y e d
when it exceeds 62 miles (100 km).
If horizontal bars are displayed
for long periods instead of di-
gits, contact a dealer.
This function is displayed only
when the vehicle is travel-
ling at a speed greater than
20 mph (30 km/h). This is the distance remaining to the
destination, either calculated at any
time by the navigation system if gui-
dance is activated or entered by the
user, minus the distance covered since
the distance was entered.
If digits are missing, dashes are dis-
played in their place.
This is the average fuel consumption
since the computer was last set to
zero.
This indicates the distance travelled
since the computer was last set to
zero.
Access via the main menu
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
Page 31 of 249
2MULTIFUNCTION SCREENS
31
D i s p l a y c o n fi g u r a t i o n C h a n g i n g t h e d a t e a n d t i m e Set the parameters one by one, using
t h e n a v i g a t o r , t h e n c o n fi r m b y c l i c k i n g
on "OK" .
From the list displayed, select " D i s p l a y
c o n fi g u r a t i o n " , t h e n c o n fi r m .
From the list displayed, select " S e t t i n g
t h e d a t e a n d t i m e " , t h e n c o n fi r m .
- Brightness, to be adjusted in accor-
dance with a scale between Moon
(-) and Sun (+).
- Selection of the units of measurement.
- Setting the date and time. Your op- erational zone is displayed on the
screen. Use the navigator to move
from one selection to another.
Y o u r n e w p a r a m e t e r s a r e c o n fi r m e d
one by one, by pressing the naviga-
tor button. All of the parameters are
r e c o r d e d i f y o u c l i c k o n O K , d i s p l a y e d
on the screen.
The ESCape button on the control pad
e n a b l e s y o u t o c h o o s e n o t t o c o n fi r m
your changes.
- Selection of the colours (on colour screen C only). From the menu, displayed on the
screen, select the icon
" P e r s o n a l i s a -
t i o n - C o n fi g u r a t i o n " using the navi-
g a t o r , t h e n c o n fi r m .
F o r s a f e t y r e a s o n s , c o n fi g u -
ration of the multifunction
screen by the driver must only
be done when stationary.
Page 65 of 249
4ACCESS
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the cas-
ing using a coin at the notch.
REINITIALISATION
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking but-
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator lamp
It is accompanied by a message on
the multi-function screen.
Your vehicle will not start.
Consult a PEUGEOT dealer.
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the following indicator lamp comes on:
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons of
your remote control out of range and
out of sight of your vehicle. You run the
risk of stopping it from working and the
remote control would have to be reini-
tialised.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reinitialisation.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Lost keys
Visit a PEUGEOT dealer with
the vehicle's V5 registration
d o c u m e n t a n d y o u r p e r s o n a l i d e n t i fi -
cation documents.
The PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a re-
placement key.
Page 68 of 249
4ACCESS
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the cas-
ing using a coin at the notch.
REINITIALISATION
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking but-
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator lamp
It is accompanied by a message on
the multi-function screen.
Your vehicle will not start.
Consult a PEUGEOT dealer.
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the following indicator lamp comes on:
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons of
your remote control out of range and
out of sight of your vehicle. You run the
risk of stopping it from working and the
remote control would have to be reini-
tialised.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reinitialisation.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Lost keys
Visit a PEUGEOT dealer with
the vehicle's V5 registration
d o c u m e n t a n d y o u r p e r s o n a l i d e n t i fi -
cation documents.
The PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a re-
placement key.
Page 69 of 249
4ACCESS
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the cas-
ing using a coin at the notch.
REINITIALISATION
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking but-
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator lamp
It is accompanied by a message on
the multi-function screen.
Your vehicle will not start.
Consult a PEUGEOT dealer.
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the following indicator lamp comes on:
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons of
your remote control out of range and
out of sight of your vehicle. You run the
risk of stopping it from working and the
remote control would have to be reini-
tialised.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reinitialisation.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Lost keys
Visit a PEUGEOT dealer with
the vehicle's V5 registration
d o c u m e n t a n d y o u r p e r s o n a l i d e n t i fi -
cation documents.
The PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a re-
placement key.
Page 112 of 249
8DRIVING
Auto-adaptive programme
select position D in the gate: the
gearbox operates in auto-adaptive
mode, without any action on your
part, taking into account the follow-
ing parameters:
- the style of driving,
- t h e p r o fi l e o f t h e r o a d ,
- the vehicle load.
To obtain maximum acceleration with-
out touching the lever, press the ac-
celerator down fully (kick down). The
programme will change down auto-
matically or will stay in the gear select-
ed until the maximum engine speed is
reached.
When the brake is applied, the pro-
gramme will change down automati-
c a l l y i n o r d e r t o p r o v i d e e f fi c i e n t e n g i n e
braking. Sport and Snow programmes
These are two special programmes.
The programme selected is displayed
on the instrument panel screen.
It is only possible to change
from one gear to another if
the vehicle speed and engine
speed permit. If they do not,
the vehicle will operate temporarily in
automatic mode.
When the vehicle is stationary or mo-
ving very slowly, the gearbox automa-
tically selects gear M1 .
Programmes S (sport) and (snow)
do not operate in manual gear selec-
tion mode.
Any operating abnormal-
ity is indicated by lighting of
this warning lamp, accom-
panied by an audible signal
and a message on the multi-function
screen.
In this situation the gearbox oper-
ates in downgrade mode (locked in
3rd gear). You may feel a substantial
knock when changing from P to R and
from N to R (this will not cause any
damage to the gearbox).
Do not exceed 60 mph (100 km/h) and
keep within local speed limits.
Have it checked by a PEUGEOT dealer.
Operating check
Operation with manual
selection of the gears
select position M in the gate,
push the lever to the + sign to
change up a gear and push again
to change up another gear,
pull the lever to the - sign to change
down a gear and pull again to
change down another gear.
You can change from position D (driv-
ing in automatic mode) to position M
(driving in manual mode) at any time.
Releasing the accelerator
sharply does not have any im-
mediate effect on the speed of
the vehicle.
Never select position
N when
the vehicle is moving.
Never select positions P or R
unless the vehicle is stationary.
Never change between positions to
optimise braking on a slippery surface. Sport programme
Press button S once the vehicle
has been started in position D , the
auto-adaptive programme favours
dynamic driving.
Snow programme
This programme improves starting and
drive when traction is poor.
Press button once the vehicle
has been started and position D has
been selected, the auto-adaptive
programme adjusts the performance
of the vehicle to the condition of the
slippery road.
You can deactivate the Sport or Snow
programme at any time by pressing
the button selected.
I f t h e b a t t e r y i s fl a t a n d t h e l e -
ver is in position P , it will be
impossible to change to an-
other position.
In particular, do not force the lever
or there is a risk the gearbox may be
damaged.
Page 148 of 249
1010PRACTICAL INFORMATION
128
ACCESSORIES
A wide range of accessories recom-
mended by PEUGEOT and original
parts are offered by the dealer net-
work.
T h e y a l l b e n e fi t f r o m P E U G E O T r e c -
ommendation.
These accessories and parts, having
been tested and approved for reliabil-
ity and safety, are all adapted to your
PEUGEOT vehicle.
The product range offered by PEU-
GEOT Accessories is structured
around 5 categories: PROTECTION -
TOURING - IN-CAR TECHNOLOGY -
STYLING - UNIVERSAL. Anti-theft alarm, parking sen-
sors, etched windows, wheel
s e c u r i t y b o l t s , fi r s t a i d k i t ,
warning triangle, high vis-
ibility safety jacket, snow
chains, anti-slip covers, dog
guard, etc.
"Protection": Seat covers compatible with
lateral airbags, mats, boot
tray.
For leisure pursuits: roof
bars, transport accessories
(bicycle carrier, ski carrier),
roof box, child seats and booster cush-
ions, rear screen blind, audio/tele-
phone console, side blinds, cool box.
T r a i l e r t o w b a r w h i c h m u s t b e fi t t e d b y
the PEUGEOT Network.
"Touring":
Telephone, Bluetooth sys-
tem, satellite navigation, CD
changer, multimedia, connec-
tion for portable MP3 player
(in the glove box), USB Box.
"In-Car Technology": Alloy wheels, wheel trims,
spoiler, leather steering
wheel, styling strips, door
spoilers, stainless steel sill
protectors.
"Styling":
W i n d s c r e e n w a s h fl u i d , i n t e -
rior and exterior cleaning and
maintenance products.
"Universal":
T h e fi t t i n g o f e l e c t r i c a l e q u i p m e n t
or accessories which are not rec-
ommended by PEUGEOT may
result in a failure of your vehicle's
electronic system.
P l e a s e n o t e t h i s s p e c i fi c w a r n i n g . Y o u
are advised to contact a representa-
tive of the Marque to be shown the
range of recommended equipment
and accessories.
Note
To avoid any jamming under the pedals:
- ensure that the mat is positioned and secured correctly,
- never place one mat on top of an- other.
Depending on the country in
which the vehicle is sold, it
may be compulsory to have
a high visibility safety jacket,
warning triangle and spare
bulbs available in the vehicle.
Installation of radiocommunication
transmitters
It is advisable to contact a representa-
tive of the PEUGEOT marque before
installing accessory radiocommunica-
tion transmitters with external aerial
on your vehicle. The PEUGEOT network will inform
y o u o f t h e s p e c i fi c a t i o n s ( f r e q u e n c y
waveband, maximum output power,
a e r i a l p o s i t i o n , s p e c i fi c i n s t a l l a t i o n
conditions) of the transmitters which
c a n b e fi t t e d , i n a c c o r d a n c e w i t h t h e
Motor Vehicle Electromagnetic Com-
patibility Directive (2004/104/EC).
407SW: you can obtain "Van" conver-
sion kits to convert from a private ve-
hicle to a van.
Page 171 of 249
152
11
2 2
3 3
4 4
5 5
6 6
7 7
8 8
0 4
GUIDANCE OPTIONS The route presented depends directly on the guidance options. Changing these options may completely change the r oute.
Press the MENU button.
Turn the dial and select the NAVIGATION GUIDANCE function.
P r e s s t h e d i a l t o c o n fi r m t h e s e l e c t i o n .
Turn the dial and select the GUIDANCE OPTIONS function.
Turn the dial and select the DEFINE CALCULATION CRITERIA function.
P r e s s t h e d i a l t o c o n fi r m t h e s e l e c t i o n .
P r e s s t h e d i a l t o c o n fi r m t h e s e l e c t i o n .
GUIDANCE OPTIONSDISTANCE/TIME
DEFINE CALCULATION CRITERIA
Turn the dial and select, for example, the DISTANCE/TIME function.
N A V I G A T I O N - G U I D A N C E