2010 Peugeot 407 Dag service indicator

4ACCESS
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the cas-
ing using a coin at the notch.
REINITIALISATION

 Switch off the ignition.

 Switch the ignition on again.


Press the remote control locking but-
ton immediately for a few seconds.

 Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator lamp
It is accompanied by a message on
the multi-function screen.
Your vehicle will not start.
Consult a PEUGEOT dealer.
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.

If the system does not function correct-
ly, the following indicator lamp comes on:
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons of
your remote control out of range and
out of sight of your vehicle. You run the
risk of stopping it from working and the
remote control would have to be reini-
tialised.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reinitialisation.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
more diffi cult in an emergency.
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Lost keys
Visit a PEUGEOT dealer with
the vehicle's V5 registration
document and your personal identifi -
cation documents.
The PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a re-
placement key.

4ACCESS
65
ALARM
For all work on the alarm system, con-
tact a PEUGEOT dealer.
- Exterior perimeter
The system checks for opening of the
vehicle.
The alarm is triggered if anyone tries
to open a door, the boot, the bonnet...
- Interior volumetric
The system checks for any variation in
the volume in the passenger compart-
ment.
The alarm is triggered if anyone breaks
a window, enters the passenger com-
partment or moves inside the vehicle.
Self-protection function
The system checks for the
putting out of service of its
components.
The alarm is triggered if the battery, the
central control or the wires of the siren
are put out of service or damaged. Locking the vehicle with full
alarm system
Activation

 Switch off the ignition and get out
of the vehicle.

 Press the locking button on the re-
mote control.
The monitoring system is active: the
indicator lamp on the button fl ashes
once per second.
After the locking button on the remote
control is pressed, the exterior perime-
ter monitoring is activated after a delay
of 5 seconds and the interior volumet-
ric after a delay of 45 seconds.
If an opening (door, boot...) is not
closed fully, the vehicle is not locked
but the exterior perimeter monitor-
ing will be activated after a delay of
45 seconds at the same time as the
interior volumetric monitoring.
System which protects and provides a
deterrent against theft and break-ins.
It provides the following types of moni-
toring.
Deactivation

 Press the unlocking button on the
remote control.
The alarm system is deactivated: the in-
dicator lamp on the button switches off.
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric pro-
tection to avoid unwanted triggering of
the alarm in certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea.
Deactivation of the interior
volumetric monitoring

 Switch off the ignition.

 Within ten seconds, press the but-
ton until the indicator lamp is lit
continuously.

 Get out of the vehicle.

 Press the locking button on the re-
mote control immediately.
The exterior perimeter monitoring alone
is activated: the indicator lamp on the
button fl ashes once per second.
To be effective, this deactivation must
be carried out each time the ignition is
switched off.