2010 Peugeot 207 Dag lock

23

Warning lamp is on Cause Action/Observations


Anti-lock
Braking System (ABS) fi xed.
The anti-lock braking
system has a fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact a
PEUGEOT dealer without delay.


Dynamic
stability control
(ESP/ASR) fl ashing.
The ESP/ASR regulation is
active. The system optimises traction and improves the
directional stability of the vehicle.
fi xed. Unless it has been
deactivated with the indicator
lamp on the button on, the
ESP/ASR system is faulty. Have it checked by a PEUGEOT dealer.

Engine
autodiagnosis system fi xed.
The emission control
system has a fault.
This lamp should switch off when the engine is sta
rted.
If it does not switch off, contact a PEUGEOT deale r
urgently.
fl ashing. The engine management
system has a fault. Risk of destruction of the catalytic convertor.
Have it checked by a PEUGEOT dealer.

Low fuel level fi xed. When it fi rst comes on there
remains
approximately
5 litres of
fuel in the tank. You must refuel as soon as possible to avoid
running out of fuel.
This warning lamp will come on every time the
ignition is switched on, until a suffi cient addition
of fuel is made.
Fuel tank capacity: approximately 50 litres
(petrol) or 48 litres (Diesel).
Never continue to drive until you run out of fuel
as this could damage the emission control and
injection systems.

i
i
27
The distance remaining may be
weighted by the time factor, de-
pending on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
Service overdue
For 5 seconds after the ignition is
switched on,
the spanner fl ashes to
indicate that the service must be carried
out as soon as possible.

Example: the service is overdue by
300 miles/km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched on,
the distance recorder resumes its normal
operation. The spanner remains lit . Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:

 switch off the ignition,

 press and hold the trip distance re-
corder zero reset button,

 switch on the ignition; the distance
recorder display begins a count-
down,

 when the display indicates "=0" , re-
lease the button; the spanner disap-
pears.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve min-
utes for the zero reset to be taken
into account.

30
Total distance recorder
System which measures the total dis-
tance travelled by the vehicle during its
life. Lighting rheostat
Permits manual adjustment of the bright-
ness of the instruments and controls in
relation to the exterior brightness. Only
operates when the vehicle lighting is on,
with the exception of the daytime run-
ning lamps. CLOCK
Integrated system which displays the
time with independent setting of hours
and minutes.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.

 With the ignition on, press the but-
ton until zeros appear. Activation

 Press the button to change the
brightness of the instruments and
controls.

 When the lighting reaches the mini-
mum setting, release the button,
then press again to increase it.
or

 When the lighting reaches the maxi-
mum setting, release the button,
then press again to reduce it.


When the lighting reaches the level of
brightness required, release the button.
Deactivation
When the vehicle lighting is off, or in
day mode on vehicles fi tted with day-
time running lamps, pressing the button
does not have any effect. Setting

 Press the corresponding button
briefl y for slow adjustment.
or

 Continue to press the corresponding
button for fast adjustment.
Button
1 : setting the hours.
Button 2 : setting the minutes.

!
!
51
No person or object must prevent
the seat slide from returning to its
initial position; return to this posi-
tion is necessary for the seat to
lock in place.
Take care not to trap the seat belt
to avoid hindering the passage of
the rear passengers.
4. Access to rear seats (3 door)

 Pull the handle to fold the seat back
and move the seat forwards. On re-
positioning, the seat returns to its
initial position. 5. Head restraint height adjustment

 To raise the head restraint, pull it up-
wards.

 To remove the head restraint, press
the lug A and pull the head restraint
upwards.

 To put the head restraint back in po-
sition, locate the stems of the head
restraint in the holes, taking care
to keep them in line with the seat
back.

 To lower the head restraint, press
the lug A and the head restraint at
the same time. The head restraint has a frame with
a notch which prevents the head
restraint from lowering; this is a
safety device which provides pro-
tection in the event of an impact.

The adjustment is correct when
the upper edge of the head re-
straint is level with the top of the
head.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted.

!
i
54

Folding the seat (SW)
This operation can be carried out at the
rear seats or through the opening rear
screen.
To avoid damaging a seat when folding it:

 move the corresponding front seat
forward if necessary,

 place the head restraints in the low
position, Check that no object could hinder
the movement of the bench seat,
either above or below.
Repositioning the seat (SW) The seat cushion lowers in order to
be covered by the seat back; this
quickly gives you a fl at boot fl oor.

 pull the control 1 forward to release
the seat back 2 which folds easily
onto the seat cushion 3 .

 When repositioning the rear seat,
straighten the seat back 2 and lock it.

 Check that the red indicator, located
at control 1 , is no longer visible.

i
!
55
MIRRORS
Door mirrors
Adjustable mirror providing the lateral
rearward vision necessary for overtak-
ing or parking. Folding

 from outside: lock the vehicle using
the remote control or the key.

 from inside: with the ignition on, pull
switch A rearwards.
Manual model Adjustment

 Move the lever in all four directions
to adjust the mirror.
The folding and unfolding of the
door mirrors can be deactivated by
a PEUGEOT dealer.
Folding

 When parked, fold the mirror manu-
ally to protect it.
Unfolding

 Before starting, unfold the mirror.
Electric model
Adjustment

 Slide switch A to the right or to the left
to select the corresponding mirror.

 Move knob B in all four directions to
adjust.

 Return switch A to the centre position. Unfolding

 from outside: unlock the vehicle us-
ing the remote control or the key.

 from inside: with the ignition on, pull
switch A rearwards.
The objects observed are, in reality,
closer than they appear.
Take this into account to correctly
judge the distance of vehicles ap-
proaching from behind.

!
i
57
STEERING WHEEL
ADJUSTMENT

 When stationary , pull the control
lever to release the steering wheel.

 Adjust the height and reach to suit
your driving position.

 Push the control lever to lock the
steering wheel.
As a safety precaution, these ope-
rations should only be carried out
while the vehicle is stationary.
Component which protects against
sunlight from the front or the side, also
equipped with an illuminated courtesy
mirror.

 With the ignition on, raise the con-
cealing fl ap; the mirror is lit automati-
cally.
This sun visor is also equipped with a
ticket holder.
TOLL CARD/CAR PARK TICKET
WINDOWS
Facility for affi xing toll cards and/or car
park tickets.
These windows are located on each
side of the base of the rear view mirror.
They are two non-refl ective areas of the
athermic windscreen.
The athermic windscreen limits
heating of the passenger compart-
ment by reducing the effects of the
sun's rays (ultra-violet). It consists
of a refl ective layer, which also
blocks certain radio-electric signals
(toll card payments, ...).

i
ACCESS
66
REMOTE CONTROL KEY
System which permits central unlocking
or locking of the vehicle using the lock
or remotely. It also locates and starts
the vehicle, as well as providing protec-
tion against theft. Unfolding the key

 First press button A to unfold the key.
Unlocking the vehicle
Unlocking is confi rmed by rapid fl ashing
of the direction indicators for approxi-
mately two seconds.
According to version, the door mirrors
unfold at the same time. Locking the vehicle

 Press the open padlock to
unlock the vehicle.
Unlocking using the key

 Turn the key to the left in the driver's
door lock to unlock the vehicle. Normal locking using the key

 Turn the key to the right in the driv-
er's door lock to lock the vehicle.
Locking is confi rmed by fi xed lighting of
the direction indicators for approximately
two seconds.
According to version, the door mirrors
fold at the same time.
Unlocking using the remote control

 Press the closed padlock to
lock the vehicle.

 Press the closed padlock
for more than two seconds
to close the windows auto-
matically in addition to lock-
ing (with sequential electric
windows).
If one of the doors, the boot or the
rear screen is still open, the central
locking does not take place.
Normal locking using the remote
control