2010 Peugeot 207 Dag bonnet

!
i
ACCESS
70
ALARM
System which protects and provides a
deterrent against the theft of your vehi-
cle. It provides two types of protection,
exterior and interior, as well as an anti-
tamper function. Locking the vehicle with full
alarm
Do not make any modifi cations to
the alarm system, this could cause
malfunctions. To be effective, this deactivation
must be carried out each time the
ignition is switched off.
Reactivation of the interior
volumetric protection

 Unlock the vehicle using the unlock-
ing button on the remote control.

 Relock the vehicle using the remote
control.
The alarm is active again with both
types of protection; the indicator lamp
on button A fl ashes once per second.
Locking the vehicle with
exterior protection only
Activation

 Switch off the ignition and get out of
the vehicle.

 Lock or deadlock the vehicle using
the locking button on the remote
control.
The alarm is activated; the indicator lamp
on button A fl ashes once per second.
Exterior perimiter protection

The system detects opening of the vehicle.

The alarm is triggered if anyone tries to
enter the vehicle by forcing a door, the
boot or the bonnet.
Interior volumetric protection
The system detects any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks
a window or moves inside the vehicle.
If you wish to leave a pet in the vehicle
or a window partially open, deactivate
the interior volumetric protection.
Anti-tamper function
The system detects the putting out of
service of its components.
The alarm is triggered if anyone tries
to put the wires of the siren, the central
control or the battery out of service.
Deactivation

 Unlock the vehicle using the unlock-
ing button on the remote control.
The alarm is deactivated; the indicator
lamp on button A switches off. Deactivation of the interior
volumetric protection

 Switch off the ignition.

 Within ten seconds, press button A
until the indicator lamp is lit continu-
ously.

 Get out of the vehicle.

 Lock or deadlock the vehicle using
the locking button on the remote
control.
The perimeter protection alone remains
activated; the indicator lamp on button A
fl ashes once per second.

i
126
BONNET
Protects the components of the engine
and provides access for checking levels.

 Push the exterior safety catch B to
the left and raise the bonnet.
 Unclip the stay C from its housing.

 Fix the stay in one of the two notch-
es to hold the bonnet open.
Closing

 Take the stay out of the support
notch.

 Clip the stay in its housing.

 Lower the bonnet and release it at
the end of its travel.

 Pull on the bonnet to check that it is
secured correctly.
RUNNING OUT OF FUEL
(DIESEL)
If your vehicle is fi tted with an HDI en-
gine, the fuel system must be primed if
you run out of fuel (refer to the corre-
sponding image).
If the engine does not start fi rst time,
don't keep trying.
Operate the priming pump again, then
the starter motor.
Opening

 Open the front left door.

 Pull the interior release lever A ,
located at the bottom of the door
frame.
The location of the interior control
prevents opening of the bonnet
while the front left door is closed.
When the engine is hot, handle the
exterior safety catch and bonnet
stay with care (risk of burns). 1.4 litre Turbo HDI engine

 Fill the fuel tank with at least fi ve litres
of diesel.

 Open the bonnet.

 Operate the priming pump until it
hardens (it may be hard on the fi rst
press).

 Operate the starter until the engine
starts.

 Close the bonnet.
1.6 litre Turbo HDI 16V engine

 Fill the fuel tank with at least fi ve litres
of diesel.

 Open the bonnet.

 Operate the priming pump until it
hardens (it may be hard at the fi rst
press).

 Operate the starter until the engine
starts.

 Close the bonnet.

151
BATTERY
Procedure for charging your battery
when it is fl at or for starting the engine
using another battery.
Access to the battery Starting using another battery

 Connect the red cable to the posi-
tive terminal (+) of the fl at battery A ,
then to the positive terminal (+) of
the slave battery B .

 Connect one end of the green or
black cable to the negative terminal
(-) of the slave battery B .

 Connect the other end of the green
or black cable to an earth point C on
the broken down vehicle, as far as
possible from the battery (for exam-
ple, right-hand engine mounting).

 Operate the starter, let the engine run.

 Wait until the engine returns to idle
and disconnect the cables.
The battery is located under the bonnet
on the left.
To gain access to it:

 open the bonnet using the interior
lever, then the exterior lever,

 secure the bonnet strut,

 remove the plastic cover to gain ac-
cess to the two terminals.

10
!
i
172
TECHNICAL DATA
IDENTIFICATION MARKINGS
Various visible markings for the identifi -
cation of your vehicle. Wheels which are fi tted with 205/45
R17 and, only on SW Outdoor,
with 205/55 R16 tyres, cannot be
fi tted with snow chains. For further
information, contact a PEUGEOT
dealer.
If the infl ation pressures are too low,
this increases fuel consumption.
The infl ation pressures must be
checked when the tyres are cold,
at least once a month.

A. Vehicle identifi cation (VIN) num-
ber under the bonnet.
This number is etched on the bodywork
near the passenger compartment fi lter.
B. Visible VIN on the dashboard.
This number is indicated on a self-
adhesive label which is visible through
the windscreen.
C. VIN on the chassis.
This number is indicated on a self-
destroying label affi xed to the centre
pillar, near the driver’s door striker.

D. Manufacturer’s label.
This label is affi xed to the edge of the
door on the driver’s side.
It bears the following information:
- the wheel rim and tyre sizes,
- the brands of tyre recommended by the manufacturer,
- the associated infl ation pressures,
- the paint colour code.