2010 Peugeot 206 P Dag tow
[x] Cancel search: towPage 3 of 107
17
Operation indicator lamps
I f o n e o f t h e f o l l o w i n g i n d i c a t o r l a m p s c o m e s o n , t h i s c o n fi r m s t h a t t h e c o r r e s p o n d i n g s y s t e m h a s c o m e i n t o o p e r a t i o n .
Warning lamp is on Cause Action/Observations
Left-hand
direction
indicato
r fl a s h i n g w i t h
buzzer. The lighting stalk is pushed
down.
Right-hand
direction
indicator fl a s h i n g w i t h
buzzer. The lighting stalk is pushed up.
Dipped beam
headlamps fi x e d . The lighting stalk is in the "Dipped
beam headlamps" position. Turn the control to the desired position
Main beam
headlamps fi x e d . The lighting stalk is pulled
towards you. Pull the stalk to return to dipped beam
headlamps.
Front
foglamps fi x e d . The front foglamps are
switched on. Turn the ring on the stalk rearwards twice to
switch off the front foglamps.
Rear
foglamps fi x e d . The rear foglamps are
switched on. Turn the ring on the stalk rearwards to switch
off the rear foglamps.
Diesel engine
pre-heating fi x e d . The ignition switch is at the
2nd position (ignition on). Wait until the warning lamp has switched off
before starting.
The duration for which the warning lamp is on
is determined by the climatic conditions.
Page 8 of 107
ii
INSTRUMENTS and CONTROLS
22
COOLANT TEMPERATURE
INDICATOR
System which informs the driver of the
changes in the temperature of the en-
gine coolant while driving.
With the engine running, when the nee-
dle is:
- in zone A , the temperature is correct,
- in zone B , the temperature is too
high; the max temperature warning
lamp
1 and the central STOP warn-
ing lamp come on, accompanied by
an audible signal and a message on
the multifunction screen.
You MUST stop as soon as it is safe
to do so.
Consult a PEUGEOT dealer. After driving for a few minutes, the tem-
perature and pressure in the cooling
system increase.
To top up the level:
wait for the engine to cool,
unscrew the cap by two turns to al-
low the pressure to drop,
when the pressure has dropped, re-
move the cap,
top up the level to the "MAX" mark
(circular line).
On petrol engines, the cooling of
the engine is managed electroni-
cally to reduce fuel consumption.
Consequently, the coolant tem-
perature levels are no longer sim-
ply linked with the external ambient
conditions and the use of the ve-
hicle.
For example, in town, it is normal
for the coolant temperature to be
slightly higher in cold weather than
in hot weather.
Page 16 of 107
i
30
The air conditioning system does
not contain chlorine and does not
present any danger to the ozone
layer. In order for these systems to be fully effective, follow the operation and main-
tenance guidelines below:
If the interior temperature remains very high after the vehicle has been
p a r k e d i n t h e s u n f o r a c o n s i d e r a b l e t i m e , fi r s t v e n t i l a t e t h e p a s s e n g e r
compartment for a few minutes.
P l a c e t h e a i r fl o w c o n t r o l a t a s u f fi c i e n t l e v e l t o p r o v i d e a n a d e q u a t e r e -
newal of air in the passenger compartment.
To obtain an even air distribution, take care not to obst ruct the exterior air
intake grille located on the bonnet, the vents and the a ir passages under
the front seats.
Operate the air conditioning system for 5 to 10 minutes, on ce or twice a
month to keep it in good working order.
E n s u r e t h a t t h e p a s s e n g e r c o m p a r t m e n t fi l t e r i s i n g o o d c o n d i t i o n a n d
h a v e t h e fi l t e r e l e m e n t s r e p l a c e d r e g u l a r l y ( r e f e r t o t h e " C h e c k s " s e c t i o n ) .
W e r e c o m m e n d t h e u s e o f a c o m b i n e d p a s s e n g e r c o m p a r t m e n t fi l t e r .
T h a n k s t o i t s s e c o n d s p e c i a l a c t i v e fi l t e r , i t c o n t r i b u t e s t o t h e p u r i fi c a t i o n
of the air breathed by the occupants and the cleanliness of the passenger
compartment (reduction of allergic symptoms, bad odours and greasy de-
posits).
To ensure correct operation of the air conditioning system, you are also
advised to have it checked regularly.
If the system does not produce cold air, do not use it and contact a
PEUGEOT dealer.
When towing the maximum load on a steep gradient in high temperatures,
switching off the air conditioning saves engine power and t herefore improves
towing capacity.
The condensation created by the air conditioning results in a discharge of
water under the vehicle which is perfectly normal.
Page 24 of 107
!i
37
1 - F o r w a r d s - b a c k w a r d s a d j u s t m e n t
Lift the control and slide the seat for-
wards or backwards.
2 - Height adjustment
Pull the handle upwards.
Remove your weight from the seat to
raise, or press on the seat to lower.
3 - Access to the rear seats
(3-door), A or B according to model
A. P l a c e y o u r fi n g e r s i n o n e o f t h e t w o
handles and push forwards to fold
down the seat back and move the
seat forwards.
When put back, the seat returns to its initial position.
No person or object must prevent the seat from returning to its initial
position. Returning to this position is
necessary for the seat to lock. 4 - Seat back angle adjustment
Push the handle towards the rear.
5 - Head restraint height adjustment
To raise the head restraint, pull it up-
wards.
T h e a d j u s t m e n t i s c o r r e c t w h e n t h e
upper edge of the head restraint is
l e v e l w i t h t h e t o p o f t h e h e a d .
T h e h e a d r e s t r a i n t i s fi t t e d w i t h a f r a m e
with notches, which prevent the head
restraint dropping down (this is a safety
device in case of impact).
FRONT SEATS
Seat consisting of a seat cushion, seat
back and head restraint which can all
be adjusted to your optimum driving
and comfort position.
Never drive with the head re-
straints removed; they should be
in place and correctly adjusted.
It is impossible to access the rear
seats if the front seat is in a reclining
position.
Heated seats
Press the switch, located on the control
panel next to the steering wheel. The
temperature is regulated automatically.
Press again to switch off.
Rear head restraint
These have a position for use (high)
and a position for storage (low).
To lower the head restraints, press the lug.
They can also be removed.
To remove the head restraints, pull up-
wards as far as the stop then press the
release control.
To lower the head restraint, push simul-
taneously:
- the button on the left-hand guide at
the base of the head restraint frame,
- the head restraint downwards.
To remove the head restraint, press the lug.
B. P l a c e y o u r fi n g e r s i n o n e o f t h e t w o
handles and push forwards to fold
down the seat back. The seat does
not move forwards.
When put back, the seat back returns to its initial angle.
Page 27 of 107
40
Removing the rear seat Folding seat back TRANSPORTING LONG OBJECTS
- Tilt the seat cushion against the front seats.
- Squeeze the seat fasteners to release them from their attachments.
- Remove the seat cushion. - Remove the head restraint for com-
plete folding of the seat back.
- Push one of the two handles 5 to-
wards the rear to tilt the seat back.
Front seat:
- Fold the seat back towards the front using the control 5 (see correspond-
ing paragraph).
Rear seat:
- Remove the seat cushion.
- Tilt the seat back.
Page 42 of 107
4949
CHILD LOCK
On each rear door, this prevents open-
ing of the door from the inside.
Turn control 1 an eighth turn (45 de-
grees) towards the inside of the vehicle
using the ignition key.
Check that the safety lock is engaged
correctly. The control 1 should no longer
be in the vertical position.
LOCKING/UNLOCKING
THE BOOT
Locking and unlocking of the boot is
simultaneous with the doors.
To open the boot, press the control A .
The lighting is controlled by opening
the boot. Tailgate release
System for mechanical unlocking of the
boot in the event of a central locking
malfunction.
Unlocking
Fold back the rear seats to gain
access to the lock from inside the
boot.
Pull the tailgate trim to detach it.
Pull the opening control 1 upwards.
Page 45 of 107
i
52
LIGHTING CONTROL STALK
System for selecting and controlling the
various front and rear lamps providing
the vehicle's lighting. Manual controls
Lighting off
Sidelamps
Dipped/Main beam head-
lamps
Lighting
The various front and rear lamps of the
vehicle are designed to improve the
driver's visibility depending on the exte-
rior conditions:
- sidelamps, to be seen,
- dipped beam headlamps, to see
without dazzling other drivers,
- main beam headlamps, for good visibility when the road is clear,
- rear foglamp, to be seen from a distance,
- front foglamps, for even better for- ward vision.
Programming
Various automatic lighting control
modes are also available according to
the following options:
- guide-me-home lighting,
- automatic illumination of headlamps. Selection is by turning ring
A .
Automatic illumination of
healamps Lighting on reminder
With the ignition off and the automatic illu-
mination of headlamps function switched
off, when the driver's door is opened,
a buzzer sounds if you have left the light-
ing on.
Front foglamps and rear
foglamp
Rotate the ring forwards to switch on
and backwards to switch off. The status
i s c o n fi r m e d b y t h e i n d i c a t o r l a m p o n
the instrument panel.
V e h i c l e s fi t t e d w i t h a r e a r
foglamp (ring B)
Dipped/Main beam change
Pull the stalk towards you. When the lighting is switched off
automatically, the rear foglamp
and the dipped headlamps re-
main on (turn the ring backwards
to switch off the rear foglamp.
The dipped beam headlamps and
sidelamps then switch off).
This only operates with the dipped/main
beam headlamps.
Page 49 of 107
i
56
A u t o m a t i c r a i n s e n s i t i v e w i n d s c r e e n
w i p e r s
In the AUTO position, the windscreen
wipers operate automatically and adapt
their speed to the intensity of the
rainfall .
Operating check
Activation
Activation of the function is accompa-
nied by a message on the multi-function
screen.
In the event of malfunction , the driver
is informed by an audible signal.
In the AUTO position, the windscreen
wiper will operate in intermittent mode.
Contact a PEUGEOT dealer to have the
system checked.
Do not cover the rain sensor located
on the windscreen behind the rear view
mirror.
When using an automatic car wash,
switch off the ignition or check that the
wiper stalk is not in the AUTO position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic rain
sensitive wipers.
W i n d s c r e e n w a s h
Pull the wiper stalk towards you. The
windscreen wash, then the windscreen
w i p e r s , o p e r a t e f o r a s p e c i fi e d t i m e .
R e a r s c r e e n w i p e r
Turn ring A t o t h e fi r s t n o t c h f o r i n t e r m i t -
tent wiping.
I f t h e i g n i t i o n i s s w i t c h e d o f f , i t i s
necessary to reactivate the control
each time . To do this, move the stalk
to any position, then move it back to the
required position.
A u t o m a t i c r e a r s c r e e n w i p e r
When the windscreen wipers control is
activated and you engage reverse gear,
the rear screen wiper operates intermit-
tently.
R e a r s c r e e n w a s h
Turn ring A p a s t t h e fi r s t n o t c h ; t h e
screen wash then the wiper operate for
a fi x e d p e r i o d . If you use a bicycle carrier, con-
sult a PEUGEOT dealer to have
this function deactivated or install
a s p e c i fi c b i c y c l e c a r r i e r a p p r o v e d
by PEUGEOT. COURTESY LAMPS
System for selecting and controlling
the various passenger compartment
lamps.
Front courtesy lamp (button A)
- when the vehicle is unlocked,
- when a door is opened,
- when the ignition is switched off.
It switches off when the vehicle is
locked.
I t fl a s h e s w h i l e d r i v i n g i f a d o o r i s n o t
closed correctly.
Permanently off.
Permanently on, when the key
is in the accessories position or
with the ignition on.
In this position, the courtesy
lamp comes on for approxi-
mately 30 seconds: