2010 NISSAN ALTIMA SEDAN center console

IP-1
BODY INTERIOR
C
DE
F
G H
I
K L
M
SECTION IP
A
B
IP
N
O P
CONTENTS
INSTRUMENT PANEL
PRECAUTION ................ ...............................2
PRECAUTIONS .............................................. .....2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
2
Precaution .................................................................2
PREPARATION ............................................3
PREPARATION .............................................. .....3
Special Service Tools ........................................ ......3
Commercial Service Tools .......................................3
SYMPTOM DIAGNOSIS ...............................4
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ........................................................... .....
4
Work Flow ........................................................... ......4
Generic Squeak and Rattle Troubleshooting ............6
Diagnostic Worksheet .......................................... .....8
ON-VEHICLE REPAIR .................................10
INSTRUMENT PANEL ASSEMBLY .................10
Exploded View ..................................................... ....10
Removal and Installation .........................................11
CENTER CONSOLE ASSEMBLY ....................14
Removal and Installation .........................................14
CLUSTER LID A ...............................................16
Removal and Installation .........................................16
DISASSEMBLY AND ASSEMBLY ..............17
CENTER CONSOLE ASSEMBLY ....................17
Exploded View ..................................................... ....17
Disassembly and Assembly .....................................17
Revision: September 20092010 Altima
ProCarManuals.com

IP-6
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
68370-4B000: 15×25 mm (0.59 ×0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll
The following materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in place of UHMW tape that will be visibl e or not fit. Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle TroubleshootingINFOID:0000000005789633
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. Acrylic lens and combination meter housing
2. Instrument panel to front pillar finishers
3. Instrument panel to windshield
4. Instrument panel mounting pins
5. Wiring harnesses behind the combination meter
6. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by
applying felt cloth tape or silicone spray (in hard to reach areas). Urethane pads can be used to insulate
wiring harness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you
will not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation pr ocedures also apply to the center console.
DOORS
Pay attention to the:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them wh ile driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the Nissan Squeak and Rattle Kit (J-43980) to repair the noise.
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1. Trunk lid bumpers out of adjustment
2. Trunk lid striker out of adjustment
3. The trunk lid torsion bars knocking together
Revision: September 20092010 Altima
ProCarManuals.com

INSTRUMENT PANEL ASSEMBLYIP-11
< ON-VEHICLE REPAIR >
C
DE
F
G H
I
K L
M A
B
IP
N
O P
Removal and InstallationINFOID:0000000005434173
CAUTION:
 Disconnect both battery terminals, then wait at least three minutes.
 Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
 Be careful not to scratch instrument panel pad and other parts.
REMOVAL
1. Remove the center console. Refer to. IP-14, "Removal and Installation"
2. Disconnect both the negative and positive battery te rminals, then wait at least three minutes.
3. Remove the A-pillar finishers, then partially remove front door welts and set aside. Refer to INT-14,
"Removal and Installation".
4. Open the glove box door (1), remove the glove box assembly screws (A).
5. Remove the glove box assembly lower screws (A), then remove the glove box assembly.
6. Remove the steering wheel. Refer to ST-12, "Removal and Installation"
.
7. Remove cluster lid A. Refer to IP-16, "Removal and Installation"
.
1. Center speaker grille 2. Tweeter speaker grille (LH) 3. Instrument panel
4. Instrument side mask (LH) 5. Combination meter 6. Lower knee protector (LH)
7. Cluster lid A 8. Instrument lower cover (LH) 9. Fuse block cover
10. Steering column cover upper 11. Steering column cover lower 12. Console side finisher (LH)
13. Storage bin 14. Cup holder M/T 15. Cup holder CVT
16. Console screw cover (LH) 17. Console rear finisher (if equipped
with rear duct) 18. Console rear finisher (without rear
duct)
19. Console screw cover (RH) 20. CVT finisher 21. Console
22. M/T finisher 23. Console side finisher (RH) 24. Cluster lid D
25. Cluster lid C 26. Center ventilator grilles 27. Glove box assembly
28. Instrument side mask (RH) 29. Tweeter speaker grille (RH) Clip
Metal clip Pawl
ALJIA0020ZZ
ALJIA0021ZZ
Revision: September 20092010 Altima
ProCarManuals.com

IP-14
< ON-VEHICLE REPAIR >
CENTER CONSOLE ASSEMBLY
CENTER CONSOLE ASSEMBLY
Removal and InstallationINFOID:0000000005789627
REMOVAL
CAUTION:
Be careful not to scratch center console finishers and other parts.
1. Move shift lever into the drive (D) position (CVT) or neutral position (M/T), then remove shift lever handle.
Refer to TM-252, "Removal and Installation"
(CVT: RE0F09B), TM-424, "Removal and Installation" (CVT:
RE0F10A), TM-22, "Removal and Installation"
(6M/T: RS6F52A).
2. Remove the cluster lid D (1).
3. Release the clips using a suitable tool, then lift t he CVT or M/T finisher upward to remove. Refer to TM-
252, "Removal and Installation".
4. Remove the storage bin (1).
5. Remove both instrument side masks (1).
ALJIA0036ZZ
ALJIA0017ZZ
ALJIA0018ZZ
Revision: September 20092010 Altima
ProCarManuals.com

CENTER CONSOLE ASSEMBLYIP-15
< ON-VEHICLE REPAIR >
C
DE
F
G H
I
K L
M A
B
IP
N
O P
6. Open the fuse block cover, remove the instrument lower cover screw (A), then remove the instrument lower cover (1).
Disconnect the asperator tube and the harness connectors.
7. Remove both the console side finishers.
8. Remove the console upper screws (A).
9. Remove the console side screws (A).
10. Position both RH and LH front seats forward.
11. Remove both the console rear screw covers, then remove the rear screws (A), then remove the console assembly.
INSTALLATION
Installation is in the reverse order of removal.
ALJIA0019ZZ
ALJIA0022ZZ
ALJIA0023ZZ
ALJIA0024ZZ
Revision: September 20092010 Altima
ProCarManuals.com

CENTER CONSOLE ASSEMBLYIP-17
< DISASSEMBLY AND ASSEMBLY >
C
DE
F
G H
I
K L
M A
B
IP
N
O P
DISASSEMBLY AND ASSEMBLY
CENTER CONSOLE ASSEMBLY
Exploded ViewINFOID:0000000005434174
Disassembly and AssemblyINFOID:0000000005434175
DISASSEMBLY
1. Remove the console assembly. Refer to IP-14, "Removal and Installation".
1. M/T finisher 2. CVT finisher 3. Storage bin (if equipped)
4. Console 5. Console screw cover (LH) 6. Console floor bracket
7. Console rear finisher (with rear duct) 8. Console rear finisher (without rear duct)9. Console lid assembly bracket
10. Console lid assembly 11. Cup holder CVT12. Cup holder M/T
Clip PawlMetal clip
AWJIA0493ZZ
Revision: September 20092010 Altima
ProCarManuals.com

IP-18
< DISASSEMBLY AND ASSEMBLY >
CENTER CONSOLE ASSEMBLY
2. Remove the cup holder screws and then remove the cup holder assembly.
3. Remove the console lid screws and remove the console lid.
4. Remove the console rear finisher.
5. Remove the console lid assembly bracket.
6. Remove the power socket from the console. Refer to PWO-5, "Removal and Installation"
.
ASSEMBLY
Assembly is in the reverse order of disassembly.
Revision: September 20092010 Altima
ProCarManuals.com