2010 MITSUBISHI LANCER SPORTBACK fuse

7-56 Vehicle care and maintenance
7
3. Clamp it on the fuse you wish to remove, and pull the fuse
straight out from the fuse block.4. Use the fuse location diagrams and the matching tables, to
check the fuse that is related to the problem. If the fuse is
not blown, something else must be causing the problem.
Contact an authorized Mitsubishi Motors dealer or a
repair facility of your choice to have the problem checked.
B- Fuse is OK
C- Blown fuse
BK0103001US.book 56 ページ ２００９年８月２０日　木曜日　午前１０時４５分

Vehicle care and maintenance
7-57
7
5. Insert a new fuse of the same capacity securely into the
appropriate slot.
Replacement of light bulbs
N00942900219
Before replacing a bulb, be sure the light is off. Do not touch
the glass part of the new bulb with your bare fingers; the oil
from your skin will stay on the glass and dim or destroy the
bulb when it gets hot.NOTE

If you are unsure of how to carry out the work as required,
it is recommended that these procedures be carried out by
an authorized Mitsubishi Motors dealer or a repair facility
of your choice.


Be careful not to scratch the vehicle body when removing
a light and lens.


When it rains, or when the vehicle has been washed, the
inside of the lens sometimes becomes temporarily foggy.
This is the same phenomenon as when window glass mists
up on a humid day, and does not indicate a functional
problem.
When the light is switched on, the heat will remove the
fog. However, if water gathers inside the light, please
have it checked by an authorized Mitsubishi Motors
dealer or a repair facility of your choice.
CAUTION
!

Never use a fuse with a capacity greater than the one
listed or any substitute, such as wire, foil etc. This
would cause the circuit wiring to heat up and could
cause a fire.


If the replacement fuse blows again after a short
time, have the electrical system checked by an
authorized Mitsubishi Motors dealer or a repair
facility of your choice to find and correct the cause.
CAUTION
!

Bulbs are extremely hot immediately after being
turned off.
When replacing a bulb, wait for it to cool sufficiently
before touching it. You could otherwise be burned.
BK0103001US.book 57 ページ ２００９年８月２０日　木曜日　午前１０時４５分

Alphabetical index
3
E
Electric rear window defogger switch 3-240
Electronic immobilizer (Anti-theft starting system) 3-4
,3-42
Emission-control system maintenance 7-41
Engine
Compartment 7-7
Coolant 7-11
,9-10
Hood 7-4
Oil and oil filter 7-8
,9-10
Overheating 6-5
Serial number 9-4
Specifications 9-8
Engine coolant temperature display 3-177
Exhaust system 7-46
External audio input connector 5-85
F
Filling the fuel tank 1-4
Floor console box 3-287
Fluid 9-10
AWC control fluid 7-19
,9-10
Brake fluid 7-21
,9-10
Clutch fluid 7-21,9-10
Continuously variable transmission (CVT) fluid 7-17
,9-10
Engine coolant 7-11
,9-10
Power steering fluid 7-22
,9-10
Twin clutch SST fluid 7-18,9-10
Washer fluid 9-10Fluid capacities and lubricants 9-10
Fog lights
Bulb capacity 7-58
Indicator 3-214
Replacement 7-75
,7-78
Switch 3-230
Free-hand advanced security transmitter (F.A.S.T.-key) 3-16
Front console boxes 3-286
Front seats 2-3
Front side-marker and parking light
Bulb capacity 7-58
Replacement 7-69,7-71
Front turn signal lights
Bulb capacity 7-58
Replacement 7-73
Fuel
Fuel economy 4-2
Fuel hoses 7-43
Modification/alterations to the electrical or fuel systems 1-9
Tank capacity 1-5,9-10
Fuel selection 1-2
Fuses 7-48
Fusible links 7-47
G
General maintenance 7-44
General vehicle data 9-6
Genuine parts 1-9
Glove compartment 3-285
BK0103001US.book 3 ページ ２００９年８月２０日　木曜日　午前１０時４５分