2010 MITSUBISHI LANCER EVOLUTION display

3-150 Features and controls
3
Rheostat meter illumination button
N00554900111
Each time you press this button, there is a sound and the bright-
ness of the instruments changes.NOTE

You can adjust to 8 different levels respectively for when
the tail lights are illuminated and when they are not.


If the vehicle is equipped with the automatic lamp control,
when the lamp switch is in the “AUTO” position, the
meter illumination switches automatically to the adjusted
brightness, depending on the brightness outside the vehi-
cle.


The brightness level of the instruments is stored when the
ignition switch is turned off.


If you press and hold the button for longer than about 1
second when the parking lights are illuminated, the bright-
ness level changes to the maximum level. Pressing and
holding the button for longer than about 1 second again
returns the brightness level to the previous level.
1- Brightness display
2- Rheostat illumination button
BK0105501US.book 150 ページ ２００９年８月１０日　月曜日　午前１０時３２分

Features and controls
3-151
3 Multi-information display
N00555000151
The multi-information display displays warnings, the odometer/trip odometer, service reminder, engine coolant temperature, fuel
remaining, outside temperature, Twin Clutch SST control mode, S-AWC (Super-All Wheel Control) control mode, gearshift lever
position, average and momentary fuel consumption, driving range, average speed, S-AWC (Super-All Wheel Control) operation
display, instrument brightness, etc.
It is also possible to change elements such as the language and units used on the multi-information display.
With ignition switch in the
“OFF” positionWith ignition switch in the “ON”
position (Twin Clutch SST)With ignition switch in the “ON”
position (manual transaxle)
1- “!” Warning display screen (With ignition switch in the
“OFF” position) →P. 3 - 1 5 3
2- Information screen (With ignition switch in the “OFF” posi-
tion) → P.3-154
Interrupt display screen (With ignition switch in the “OFF”
position) → P.3-156
3- Door ajar warning display screen (With ignition switch in
the “OFF” position) → P.3-157
4- S-AWC control mode display screen → P.3-159
5- Outside temperature display screen → P.3-1676- “!” Warning display screen (With ignition switch in the
“ON” position) → P.3-159
7- Information screen (With ignition switch in the “ON” posi-
tion) → P.3-160
Interrupt display screen (With ignition switch in the “ON”
position) → P. 3 - 1 6 5
8- Fuel remaining display screen → P.3-167
9- Twin Clutch SST control mode display screen (if so
equipped) → P. 3 - 1 6 7
BK0105501US.book 151 ページ ２００９年８月１０日　月曜日　午前１０時３２分

3-152 Features and controls
3
NOTE

The trip computer function fuel units, temperature units,
display language, and other settings can be changed.
Refer to “Changing the function settings (With ignition
switch in the “ON” position)” on page 3-171.


The display screen is different depending on whether the
ignition switch in the “OFF” or “ON” position.
Refer to “Information screen (With ignition switch in the
“OFF” position)” on page 3-154.
Refer to “Warning display list (With ignition switch in the
“OFF” position)” on page 3-185.
Refer to “Information screen (With ignition switch turned
from “OFF” to “ON”)” on page 3-158.
Refer to “Information screen (With ignition switch in the
“ON” position)” on page 3-160.
Refer to “Warning display list (With ignition switch in the
“ON” position)” on page 3-188.
10- Gearshift lever position display screen (if so equipped) →
P.3-166
11- Active Stability Control (ASC) OFF display screen → P. 3 -
129BK0105501US.book 152 ページ ２００９年８月１０日　月曜日　午前１０時３２分

Features and controls
3-153
3
Multi-information meter switch
N00555100110
The multi-information meter switch is a button marked
“INFO” on the left side of the dash.
Each time the multi-information meter switch is operated, a
sound is emitted and the multi-information display changes
between information such as warnings, service reminder, aver-
age and momentary fuel consumption, driving range, average
speed, and S-AWC operation display.
It is also possible to change elements such as the language and
units used on the multi-information display by operating the
multi-information meter switch.
“!” Warning display screen (With ignition switch
in the “OFF” position)
N00555200078
If you press the multi-information meter switch and return
from the warning display screen to the previous screen, the “!”
warning is displayed.
Refer to “Returning to the display screen from before the warn-
ing display” on page 3-156.
This mark is also displayed if there is another warning other
than the one displayed. When the cause of the warning display
is eliminated, the “!” warning goes out automatically.NOTE

When the “!” warning is displayed, the warning display
screen can be redisplayed on the information screen.
Refer to “Information screen (With ignition switch in the
“OFF” position)” on page 3-154.
Refer to “Information screen (With ignition switch in the
“ON” position)” on page 3-160.
BK0105501US.book 153 ページ ２００９年８月１０日　月曜日　午前１０時３２分

3-154 Features and controls
3
Information screen (With ignition switch in the
“OFF” position)
N00555300095
Each time you lightly press the multi-information meter
switch, the display screen switches in the following order.
1-
Odometer/Trip odometer
2-
Odometer/Trip odometer
3- Service reminder
4- Redisplay of a warning display screen
When there is no
warning display
When there is a
warning display
BK0105501US.book 154 ページ ２００９年８月１０日　月曜日　午前１０時３２分

Features and controls
3-155
3
Odometer/Trip odometer
N00555400083
Each time you lightly press the multi-information meter
switch, the display screen switches.
Odometer/tripmeter → Odometer/tripmeter → Service
reminder → Redisplay of a warning display screen → Odome-
ter/tripmeter .
Odometer
Shows the total distance traveled.
Trip odometer
Shows the distance traveled between two points.

To reset the trip odometer
To return the display to 0, hold down the multi-information
meter switch for about 2 seconds or more. Only the currently
displayed value will be reset.
Example
If tripmeter is displayed, only tripmeter will be reset.
NOTE

If there is no warning display, the switching sequence is:
odometer/tripmeter → odometer/tripmeter → ser-
vice reminder → odometer/tripmeter .


Both tripmeters and can count up to 9999.9
miles/kilometers.
When a tripmeter goes past 9999.9 miles/kilometers, it
returns to 0.0 miles/kilometers.


When disconnecting the battery terminal, the memories of
tripmeter displays and are cleared, and their dis-
plays return to “0.0 miles/kilometers”.
Service reminder
N00555500013
Shows the distance and number of months until the next peri-
odic inspection.
Refer to “Service reminder” on page 3-168.
Usage examples for tripmeter , tripmeter
It is possible to measure two currently traveled distances,
from home using tripmeter and from a particular point
on the way using tripmeter .
BK0105501US.book 155 ページ ２００９年８月１０日　月曜日　午前１０時３２分

3-156 Features and controls
3
Interrupt display screen (With ignition switch in
the “OFF” position)
N00559600139
When there is information to be announced, such as a key
reminder, the buzzer sounds and switches to the warning dis-
play screen. Refer to the appropriate page and take the neces-
sary measures.
When the cause of the warning display is eliminated, the warn-
ing display goes out automatically.
Refer to “Warning display list (With ignition switch in the
“OFF” position)” on page 3-185.
Returning to the display screen from before the warn-
ing displayEven if the cause of the warning display is not eliminated, you
can return to the screen that was displayed before the warning
display.
If you press the multi-information meter switch, the display
screen switches to the screen display from before the warning
and the “!” warning is displayed.
1- Information generated
2- Cause eliminated
A- “!” warning
BK0105501US.book 156 ページ ２００９年８月１０日　月曜日　午前１０時３２分

Features and controls
3-157
3
NOTE

Warning display screens with a “ ” or “ ” mark dis-
played in the upper right of the screen can be switched. If
you want to switch the display, press the multi-informa-
tion meter switch as follows.
“ ”: Press lightly.
“ ”: Press for about 2 seconds or more.
Redisplay of a warning display screen
When the “!” warning is displayed, if you lightly press the
multi-information meter switch a few times, the warning dis-
play screen you switched from is redisplayed.
Refer to “Information screen (With ignition switch in the
“OFF” position)” on page 3-154.
Door ajar warning display screen (With ignition
switch in the “OFF” position)
N00559700114
If any of the doors or the trunk lid is not completely closed, this
displays the open door or trunk lid.1- Doors and trunk lid are closed
2- Doors or trunk lid is open
BK0105501US.book 157 ページ ２００９年８月１０日　月曜日　午前１０時３２分