2010 MERCEDES-BENZ CL CLASS sensor

normally be done every 3 to 5 months,
depending on the climate and washing
detergent used.
Mercedes-Benz approved Paint Cleaner
should be applied if the paint surface shows
signs of embedded dirt (i.e. loss of gloss).
Do not apply any of these products or wax if
your
vehicle
is parked in the sun or if the hood
is still hot.
X Use the appropriate MB-Touch-Up Stick for
quick and

provisional repairs of minor paint
damage (i.e. chips from stones, vehicle
doors, etc.).
Engine cleaning Prior to cleaning the engine compartment,
make sure to protect electrical components
and connectors from contact with water and
cleaning agents.
Corrosion protection, such as MB
Anticorrosion Wax should be applied to the
engine compartment after every engine
cleaning. Before applying, all control linkage
bushings
and

joints should be lubricated. The
poly-V-belt and all pulleys should be
protected from any wax.
Vehicle washing In the winter, thoroughly remove all traces of
road salt as soon as possible.
When
washing

the vehicle underbody, do not
forget to clean the inner sides of the wheels.
i Vehicles with KEYLESS-GO:
If a door handle is hit by a strong jet of
water, and a SmartKey is within
approximately 3 ft (1 m) of the vehicle, it
could be inadvertently locked or unlocked.
Hand-wash
X Do not use hot water or wash your vehicle
in direct sunlight.
X Only use a soft, wet cloth or sponge to
clean the vehicle. X
Only use a mild vehicle wash detergent,
such as Mercedes-Benz approved Car
Shampoo.
X Thoroughly spray the vehicle with a
diffused jet of water.
X Do not spray directly towards the
ventilation intake.
X Use plenty of water and rinse the sponge
and chamois frequently.
X Rinse with clean water and dry with a
chamois thoroughly.
Do not allow cleaning agents to dry on the
finish.
Automatic car wash G
Warning!
The vehicle is braked when the HOLD function
or DISTRONIC PLUS is activated. Therefore,
deactivate the HOLD function or DISTRONIC
PLUS before the vehicle is washed in an
automatic car wash.
You can have your vehicle washed in an
automatic car

wash from the start. Brushless
car washes are preferable.
X To protect the filter system, activate the air
recirculation mode using rocker switch
g on the climate control panel.
! Do not

clean your vehicle in an automatic
touchless car wash which uses caustic
spray. Caustic spray will damage the paint
or ornamental moldings.
If the vehicle is very dirty, prewash it before
running it through the automatic car wash.
! Make sure the combination switch is set
to wiper setting $. Otherwise, the rain
sensor could activate and cause the wipers
to move unintentionally. This may lead to
vehicle damage.
Due to the width of the vehicle, fold in
exterior rear view mirrors prior to running
the vehicle through an automatic car wash
to prevent damage to the mirrors. Vehicle care
405
Operation
216_AKB; 3; 90, en-US
d2ureepe, Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 405 Z

X
When taking the vehicle through an
automatic conveyor-type car wash:
Make sure the automatic transmission
remains in neutral position N. Observe
instructions, see “Remaining in neutral
position N” (Y page 292).
When leaving the automatic car wash, make
sure the mirrors are folded out.
After running the vehicle through an
automatic car wash, wipe any wax off of the
windshield and the wiper blade inserts. This
will prevent smears and reduce wiping noise
which can be caused by residual wax on the
windshield.
Ornamental moldings X
For regular cleaning and care of ornamental
moldings, use a damp cloth.
! Do not use chrome cleaner on ornamental
moldings. Although ornamental moldings
may have chrome appearance, they could
be made of anodized aluminum that will be
damaged when cleaned with chrome
cleaner. Instead, use a damp cloth to clean
those ornamental moldings.
For very dirty ornamental moldings of
which you are sure are chrome-plated, use
a chrome cleaner. If in doubt whether an
ornamental molding is chrome-plated,
contact an authorized Mercedes-Benz
Center.
Headlamps, brake lamps, tail lamps,
side markers, turn signal lenses X
Use a mild vehicle wash detergent, such as
Mercedes-Benz approved Car Shampoo,
with plenty of water.
! Only use window cleaning solutions that
are suitable for plastic lamp lenses.
Window cleaning solutions which are not
suitable may damage the plastic lamp
lenses of the headlamps. Therefore, do not
use abrasives, solvents or cleaners that
contain solvents. Cleaning the driving systems sensors
X
Switch off the ignition.
X Clean DISTRONIC PLUS/PRE-SAFE ®
Brake
system sensor cover : by hand.
To clean DISTRONIC PLUS/PRE-SAFE ®
Brake
system sensor cover : and the bumper area
near sensors ; observe the following:
R Use a mild vehicle wash detergent, such as
Mercedes-Benz approved Car Shampoo,
with plenty of water.
R Use a soft, non-scratching cloth.
! If you use a power washer to clean the
sensor covers, observe the following:
R Follow the instructions provided by the
power washer manufacturer.
R Maintain a distance between the sensor
covers and the nozzle of the power
washer. 406
Vehicle careOperation
216_AKB; 3; 90, en-US
d2ureepe,
Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 406

Text messages
Safety systems Display messages
Possible causes/consequences and
X SolutionsPRE-SAFE Inoperativ
e See
Oper.
Manual
The PRE-SAFE
®
system has failed. All other occupant safety
systems, such as the air bags, are still available.
X Contact an authorized Mercedes-Benz Center as soon as
possible. PRE-SAFE Function
Currently
Limited
See Oper.
Manual
The PRE-SAFE
®
Brake is temporarily unavailable.
The PRE-SAFE ®
Brake is deactivated because:
R the DISTRONIC PLUS cover in the radiator grille is dirty
R the area
around the sensors in the front or the rear bumper
is dirty
R its function is impaired as a result of heavy precipitation
R the radar sensor system is temporarily inoperative due to
electromagnetic interference near television and radio
transmitter stations, toll stations, speed measuring
systems, etc.
R the system is out of the operating temperature range
R the battery voltage is insufficient
The PRE-SAFE ®
Brake becomes operational again and the
message in the multifunction display disappears when:
R dirt on the radiator grille has fallen off while driving (e.g.
slush or snow)
R the system recognizes full sensor availability (due to
lessening rain or the road surface drying)
R the system is within the operating temperature range
If the message in the multifunction display does not
disappear:
X Clean the DISTRONIC PLUS cover in the radiator grille
(Y page 406).
X Clean the front and the rear bumper ( Y page 406).
X Restart the vehicle.
X Wait until the battery recovers. PRE-SAFE Function
Limited
See Oper.
Manual
The PRE-SAFE
®
Brake is unavailable due to a malfunction.
The BAS PLUS may also be unavailable.
X Contact an authorized Mercedes-Benz Center as soon as
possible. 416
Vehicle status messages in the multifunction display
Practical hints
216_AKB; 3; 90, en-US
d2ureepe,
Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 416

Display messages
Possible causes/consequences and
X SolutionsDISTRONIC
PLUS Currently
Unavailabl
e See
Oper.
Manual The DISTRONIC PLUS is temporarily unavailable.
The DISTRONIC PLUS is deactivated because:
R
the DISTRONIC PLUS cover in the radiator grille is dirty
R its function is impaired as a result of heavy precipitation
R the radar sensor system is temporarily inoperative due to
electromagnetic interference near television and radio
transmitter stations, toll stations, speed measuring
systems, etc.
R the radar sensors do not sense any other vehicles or
objects, i.e. road sign or similar to this, for a long time
R the system is out of the operating temperature range
R the battery voltage is insufficient
X If necessary, clean the DISTRONIC PLUS cover in the
radiator grille (Y
page 406).
X Restart the vehicle.
X Try activating the DISTRONIC PLUS again later.
X Wait until the system is within the operating temperature
range or the battery recovers.
The DISTRONIC PLUS becomes operational again without the
engine being restarted when:
R dirt on the radiator grille has fallen off while driving (e.g.
slush or snow)
R the system recognizes full sensor availability (due to
lessening rain or the road surface drying)
R the message in the multifunction display disappears DISTRONIC
PLUS Inoperativ
e The DISTRONIC PLUS is malfunctioning.
The BAS PLUS and the PRE-SAFE
®
Brake are also not
available.
X Contact an authorized Mercedes-Benz Center as soon as
possible. DISTRONIC
PLUS Override You have accelerated. The DISTRONIC PLUS has switched off.
X
Stop accelerating. Vehicle status messages in the multifunction display
421
Practical hints
216_AKB; 3; 90, en-US
d2ureepe,Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 421 Z

Display messages
Possible causes/consequences and
X SolutionsDISTRONIC
PLUS - - - mph One of the activation conditions for the DISTRONIC PLUS has
not been fulfilled. You may have attempted to set a speed
below 20 mph (
30 km/h)
.
X Drive faster than 20 mph (30 km/h) if the situation allows
and set the speed.
X Check the activation conditions for the DISTRONIC PLUS
(Y page 309). HOLD Off The HOLD function switched off because the vehicle was
sliding, for example on a slippery surface.
X
Activate the HOLD function later. Park
Assist Currently
Unavailabl
e See
Oper.
Manual The Park Assist is deactivated because the area around the
sensors in the front or the rear bumper is dirty.
X
Clean the front and rear bumper ( Y page 406). The Park Assist is deactivated because the battery voltage is
insufficient.
X
Have the battery checked at an authorized Mercedes-Benz
Center. The Park Assist is switched off because the radar sensor
system is temporarily inoperative due to electromagnetic
interference near television and radio transmitter stations,
toll stations, speed measuring systems, etc.
X
Wait until the message in the multifunction display
disappears. Park
Assist Inoperativ
e The Park Assist is malfunctioning.
X
Contact an authorized Mercedes-Benz Center as soon as
possible. 422
Vehicle status messages in the multifunction display
Practical hints
216_AKB; 3; 90, en-US
d2ureepe,
Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 422

Display messages
Possible causes/consequences and
X SolutionsBlind
Spot
Assist Currently
Unavailabl
e See
Oper.
Manual The Blind Spot Assist is deactivated because the area around
the sensors in the front or the rear bumper is dirty.
X
Clean the front and rear bumper ( Y page 406). The Blind Spot Assist is deactivated because the battery
voltage is insufficient.
X
Have the battery checked at an authorized Mercedes-Benz
Center. The Blind Spot Assist is switched off because the radar sensor
system is temporarily inoperative due to electromagnetic
interference near television and radio transmitter stations,
toll stations, speed measuring systems, etc.
X
Wait until the message in the multifunction display
disappears. Blind
Spot
Assist Inoperativ
e The Blind Spot Assist is malfunctioning.
X
Contact an authorized Mercedes-Benz Center as soon as
possible. Parking
Guidance Currently
Unavailabl
e See
Oper.
Manual The Advanced Parking Guidance is deactivated because the
area around the sensors in the front or the rear bumper is
dirty.
X
Clean the front and rear bumper ( Y page 406). The Advanced Parking Guidance is deactivated because the
battery voltage is insufficient.
X
Have the battery checked at an authorized Mercedes-Benz
Center. The Advanced Parking Guidance is switched off because the
radar sensor system is temporarily inoperative due to
electromagnetic interference near television and radio
transmitter
stations,
toll stations, speed measuring systems,
etc.
X Wait to see if the interference is temporary. Try in a location
where the interfering source might not be present. Vehicle status messages in the multifunction display
423
Practical hints
216_AKB; 3; 90, en-US
d2ureepe,Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 423 Z

Display messages
Possible causes/consequences and
X SolutionsParking
Guidance Canceled The Advanced Parking Guidance has been canceled because:
R
the vehicle is sliding
R the bumper became dirty in the area of the sensors
R there has been a malfunction
X Use the Advanced Parking Guidance again later.
If the parking space symbol is not shown in the multifunction
display at a speed below 10 mph (16 km/h):
X Clean the bumpers
(Y page 406).
or
X Restart the engine.
or
X Contact an authorized Mercedes-Benz Center. Parking
Guidance Finished Advanced Parking Guidance: The vehicle is in the end
position.
The display message disappears automatically.
Radar
Sensors Deactivate
d See
Oper.
Manual You have attempted to activate the DISTRONIC PLUS, the
Park Assist or the PRE-SAFE
®
Brake even though you have
switched off the radar sensors on the vehicle.
X Check if switching on the radar sensors is permitted
(Y page 216).
X Switch on the radar sensors using the instrument cluster
control system. Vehicle
Display messages
Possible causes/consequences and
X SolutionsApply
Brake to Shift
from 'P' You have attempted to shift the automatic transmission into
drive
position D

, reverse gear R or neutral position N without
depressing the brake pedal.
X Depress the brake pedal. Door Open Vehicle
Not in
Park You have opened the driver’s door and the automatic
transmission is still in drive position
D, reverse gear R or
neutral position N.
X Before you leave the vehicle, make sure the automatic
transmission is

in park position P and the electronic parking
brake is engaged. 424
Vehicle status messages in the multifunction display
Practical hints
216_AKB; 3; 90, en-US
d2ureepe,
Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 424

Display messages
Possible causes/consequences and
X SolutionsNext
Service X in ...
days
in ...
mls (km) The specified maintenance service must be carried out within
the remaining time range or driving distance (Y page 402).
X
Have the maintenance service carried out at an authorized
Mercedes-Benz Center. Service X Due The specified maintenance service must be carried out
(Y page 402).
X
Have the maintenance service carried out at an authorized
Mercedes-Benz Center as soon as possible. Service X
Exceeded by X days
by XXX
mls (km) The specified maintenance service term has been exceeded
(Y page 402).
X
Have the maintenance service carried out at an authorized
Mercedes-Benz Center as soon as possible. !
Failure to have the vehicle maintained in
accordance with the Maintenance Booklet
and maintenance service indicator at the designated times/mileage will result in
vehicle damage not covered by the
Mercedes-Benz Limited Warranty.
Tires Display messages
Possible causes/consequences and
X SolutionsTire
Pressures Displayed
After
Driving A
Few
Minutes The tire inflation pressure is being checked by the Advanced
TPMS.
X
Drive the vehicle for a few minutes. Tire
Pressure
Monitor Inoperativ
e The Advanced TPMS is malfunctioning.
X
Have the Advanced TPMS checked at an authorized
Mercedes-Benz Center. Tire
Pressure
Monitor Inoperativ
e No
Wheel
Sensors There are wheels without appropriate wheel sensors mounted
(e.g. winter tires).
X
Have the appropriate wheel sensors installed at an
authorized Mercedes-Benz Center. 426
Vehicle status messages in the multifunction displayPractical hints
216_AKB; 3; 90, en-US
d2ureepe,
Version: 2.11.8.1 2009-05-15T11:47:50+02:00 - Seite 426