2010 Lancia Delta warning lights

14GETTING TO KNOW YOUR CAR
General failure indication (amber)
Fuel cut-off initiated
This warning light (or symbol on the display)
comes on when the fuel cut-off system cuts in.
The display will show a dedicated message.
Engine oil pressure sensor failure
This warning light (or symbol on the display) comes on
when a failure is detected in the engine oil pressure sen-
sor. The display will show a dedicated message.
Dusk sensor failure
This warning light (or symbol on the display) comes on
when a failure is detected in the dusk sensor.
Speed limit exceeded
This warning light (amber), or symbol on the display
(red), comes on when the preset speed limit is exceeded
(for Arabic countries the speed limit is set at 120 km/h).
The display will show a dedicated message.
Rain sensor failure
(for versions/markets, where provided)
This warning light (or symbol on the display) comes on
when a fault is detected in the rain sensor.
The display will show a dedicated message.
è
Parking sensor failure
(for versions/markets, where provided)
This warning light (or symbol on the display) comes on
when a fault is detected in the parking sensors.
The display will show a dedicated message.
Tyre pressure monitoring system failure
(for versions/markets, where provided)
This warning light (or symbol on the display) comes on
when a failure is detected in the T.P.M.S. system (for ver-
sions/markets, where provided).
Should one or more wheels be fitted without sensors, the
instrument panel warning light will come on and stay on
until initial conditions are restored.
The display will show a dedicated message.
NOTE If one of the above-mentioned faults occurs,
contact a Lancia Dealership as soon as possible.
AFS system failure
This warning light (or symbol on the display) comes on
when a failure is detected in the AFS system (see “Head-
lights” paragraph in this chapter). The display will show
a dedicated message.
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 14

GETTING TO KNOW YOUR CAR17
1
Glow plug preheating
This warning light comes on when the key is
turned to MAR. It will go out as soon as the glow
plugs have reached a predetermined temperature.
Start the engine as soon as the warning light goes out.
IMPORTANT At high outdoor temperatures the warning
light stays on for an extremely short time.
Glow plug heating failure
The warning light will blink in the event of a failure in the
glow plug preheating system. Go to a Lancia Dealership
as soon as possible.
The display will show a dedicated message.
m
Water in diesel fuel filter (Multijet
versions) (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after
a few seconds. The warning light turns on when there is
water in the diesel fuel filter. The display will show a ded-
icated message.
c
The presence of water in the fuel system circuit
may cause severe damage to the injection sys-
tem and irregular engine operation. If the
c
warning light comes on (together with a message on the
display on some versions), go to a Lancia Dealership
as soon as possible to have the system bled. Water may
have been introduced in the tank if this appears im-
mediately after refuelling: in this case, stop the engine
immediately and contact a Lancia Dealership.
ABS system failure (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after a
few seconds. The warning light lights up when the
system is either not working or not available. Under these cir-
cumstances the braking system will work as normal with-
out the extra performance offered by the ABS system.
Drive carefully to the nearest Lancia Dealership to have the
system checked.
The display will show a dedicated message.
>
Lancia Code system failure (amber)
This warning light (or symbol on the display),
when on constantly with the ignition key turned
to MAR, indicates a possible failure (see “Lancia
Code system” in chapter 1).
Y
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 17

18GETTING TO KNOW YOUR CAR
If the Ywarning light (or symbol in the display) is blinking,
this means that the vehicle is not protected by the engine in-
hibitor device (see “Lancia Code system” in chapter 1).
Contact a Lancia Dealership to have all the keys stored.
Alarm failure
(for versions/markets, where provided)
A fault with the alarm system is signalled by this warn-
ing light (or symbol in the display) coming on. Contact a
Lancia Dealership as soon as possible.
The display will show a dedicated message.
Break-in attempt
(for versions/markets, where provided)
This warning light (or symbol on the display) comes on
when a break-in attempt is detected. Contact a Lancia
Dealership as soon as possible.
The display will show a dedicated message.The warning light (amber), or symbol on the display (red),
lights up when the inflation pressure of one or more tyres
falls below a preset level. In this way the T.P.M.S. system warns
the driver that one or more tyres may be dangerously flat and
liable to puncture (see “ T.P.M.S. system” in this chapter).
IMPORTANT Do not continue driving with one or more
tyres flat as vehicle driveability may be compromised. Stop
the car, avoiding harsh braking or steering manoeuvres. Re-
place the wheel immediately with the small spare wheel (for
versions/markets, where provided) or carry out a repair us-
ing the dedicated kit (see the paragraph on “Replacing a
wheel” in chapter 4) and contact a Lancia Dealership as
soon as possible.
Check tyre pressure
This warning light (for versions/markets, where provid-
ed) comes on when the ignition key is turned to MAR, but
it should go off after a few seconds.
The warning light (or symbol in the display) lights up to
indicate that a tyre is flat (see “T.P.M.S. system ” in this
chapter).
Should two or more tyres be flat, the display will show the
indications corresponding to each tyre in sequence. Restore
the correct inflation pressure values as soon as possible (see
paragraph “Cold inflation pressures” in chapter “6”). Insufficient tyre inflation pressure
(for versions/markets, where provided)
This warning light (or symbol on the display)
comes on when the ignition key is turned to MAR,
but it should go off after a few seconds.
n
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 18

GETTING TO KNOW YOUR CAR19
1
Particularly strong radio frequency interfer-
ence may cause the T.P.M.S. system to func-
tion incorrectly. This condition is indicated
to the driver by a message (for versions/markets,
where provided).
The warning message will go off automatically as
soon as the radio-frequency noise ceases to disturb
the system.
External lighting failure (amber)
This warning light (or symbol on the display)
comes on when a failure is detected in any of
the following lights:
❍sidelights;
❍brake lights (for versions/markets, where provided);
❍rear fog lights;
❍direction indicators;
❍number plate lights;
❍daylight lights.
W
Rear fog lights (amber)
The warning light comes on when the rear fog
lights are turned on.
4
Front fog lights (green)
The warning light comes on when the front fog
lights are turned on.
5
Direction indicators
(green - intermittent)
The warning lights turn on when the direction
indicator control lever is moved downwards,
upwards or when the hazard warning light
button is pressed.
F
D
Tyre pressure unsuitable for speed
This warning light (for versions/markets, where provid-
ed) comes on when the ignition key is turned to MAR, but
it should go off after a few seconds.
Should it be necessary to travel at a speed higher than 160
km/h, inflate the tyres to the pressure value specified in
paragraph “Inflation pressures” in chapter “6”.
If the T.P.M.S. system (for versions/markets, where pro-
vided) detects that the inflation pressure of one or more
tyres is unsuitable for the speed being maintained, it lights
up the warning light or symbol (together with a message
shown on the display) (see paragraph “Insufficient tyre
inflation pressure” in this chapter). The warning light
remains on until the vehicle speed is reduced to below a
certain threshold (see paragraph “T.P.M.S. system” in this
chapter).
IMPORTANT reduce speed immediately if this occurs.
Tyre overheating could irreparably compromise tyre per-
formance and life, and in extreme cases may even cause
the tyre to explode.The fault relating to these lights may be caused by: one or
more burnt lamps, a blown protection fuse or interruption
of the electrical connection.
The display will show a dedicated message.
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 19

20GETTING TO KNOW YOUR CAR
Daylight lights/dipped beam headlights
(green)
This warning light comes on when the daytime
lights or dipped beam headlights are turned on.
Follow me home
This warning light comes on when this device is activat-
ed (see “Follow me home” in chapter “1”).
The display will show a dedicated message.
3
Main beam headlights (blue)
This warning light comes on when the main
beam headlights are turned on.
1
Cruise control system
(green)
(for versions/markets, where provided)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after a few sec-
onds. The warning light is lit up on the display by rotat-
ing the Cruise Control selector wheel to ON.
The display will show a dedicated message.
Ü
DISPLAY
The car can be equipped with a multifunctional/ recon-
figurable multifunctional display which, according to the
settings carried out, will show useful information when
driving.
MULTIFUNCTIONAL DISPLAY “STANDARD”
SCREEN fig. 4
The standard screen shows the following information:
A. Date
B. Possible activation of Dualdrive electric power steering
C. Sport driving mode indication (for versions/markets,
where provided)
D. Time
E. Odometer (distance travelled in kilometres/miles)
F. Possible presence of ice on road
G. Outside temperature
H. Scheduled servicing deadline
I. Headlight alignment position (with dipped beam head-
lights on only).
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 20

24GETTING TO KNOW YOUR CAR
Selecting an option from the main menu
without submenu:
– briefly press the SET button to select the main menu op-
tion to be set.
– Press button
ÕorÔ(by single presses) to select a new
setting;
– briefly press the SET button to store the new setting and
to go back to the main menu option selected previously.
Selecting an option from the main menu with
submenu:
– briefly press the SET button to display the first submenu
option;
– press button
ÕorÔ(by single presses) to scroll through
all the submenu options;
– briefly press the SET button to select the displayed sub-
menu option and to open the relevant set-up menu;
– press
ÕorÔ(by single presses) to select a new setting
for this submenu option;
– briefly press the SET button to store the new setting and
to go back to the previously selected submenu option.
MENU ITEMS
Lighting (Adjusting lighting
inside the car)
This function may be used to set the brightness of the in-
strument panel, sound system controls and automatic cli-
mate control system controls (for versions/markets, where
provided) to 8 levels.
Proceed as follows to adjust the brightness:
– briefly press SET. The previously set level will flash on
the display;
– press
ÕorÔto set the required brightness level;
– briefly press SET to go back to the menu screen or hold
the button down to go back to the standard screen with-
out storing the new settings.
Speed beep (Speed limit)
This function may be used to set the car speed limit (km/h
or mph); when this limit is exceeded the driver is imme-
diately alerted (see “Instrument panel warning lights” in
chapter 1). To set the speed limit, proceed as follows:
– briefly press SET. The display will show a dedicated mes-
sage;
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 24

32GETTING TO KNOW YOUR CAR
Daytime lights (D.R.L. - Smart Daytime Light)
This function allows you to activate/deactivate the day-
light lights.
Proceed as follows to switch this function on or off:
– briefly press SET to display a submenu;
– briefly press SET: (On) or (Off) will flash on the display
(according to previous setting);
– press + or – to change the setting;
– briefly press the SET button to go back to the submenu
screen or hold the button down to go back to the main
menu screen without storing the new settings;
– hold down SET to go back to the standard screen or
main menu, depending on which point in the menu you
have reached.
Exit Menu
This is the last function that closes the setting cycle list-
ed in the initial menu screen. Briefly press SET to go back
to the standard screen without storing the new settings.
Press
Ôto return to the first menu option (Speed Beep).DISPLAY INDICATIONS
IMPORTANT Failure indications on the display fall into
one of two categories: serious faults and less serious faults.
Serious failures are indicated by a repeated and prolonged
warning cycle.
Less serious failures are indicated by a limited warning
cycle.
Press SET to stop the warning cycle in both cases. The
warning light (or symbol in the display) will remain on
until the cause of the malfunction is eliminated.
Luggage compartment not closed
correctly (red)
This symbol (for versions/markets, where pro-
vided) lights up on the display when the luggage
compartment is not closed correctly. The display will show
a dedicated message.
R
Bonnet not closed correctly (red)
This symbol (for versions/markets, where pro-
vided) lights up on the display when the bon-
net is not closed correctly. The display will show
a dedicated message.
S
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 32

42GETTING TO KNOW YOUR CAR
IMPORTANT The engine inhibitor function is guaranteed
by the Lancia CODE, which is automatically activated
when the ignition key is extracted from the starter de-
vice.
SWITCHING ON THE ALARM
With the doors and bonnet closed and the ignition key
either turned to STOP or removed, point the key with the
remote control towards the vehicle and press and release
button
Á.
Excluding some versions for specific markets, the system
produces an acoustic warning (beep) and enables door
locking.
Before the alarm is enabled, a self-diagnosis test is run:
if a fault is detected, the system emits another sound warn-
ing and a message is shown on the display, (see “Instru-
ment panel warning lights”).
In this case switch off the alarm by pressing
Ë, check that
all the doors, bonnet and tailgate are closed correctly; then
switch the alarm back on by pressing
Á.
If a door or the bonnet is not correctly closed, it will be ex-
cluded from the testing by the alarm system.
If the alarm produces an acoustic signal even when the
doors, bonnet and tailgate are correctly closed, a failure
has occurred in system operation. Contact a Lancia Deal-
ership.IMPORTANT Centrally locking the doors using the met-
al insert on the key does not activate the alarm.
IMPORTANT Originally, the alarm is configured in com-
pliance with the regulations existing in the different coun-
tries.
SWITCHING OFF THE ALARM
Press button
Ëon the key with the remote control.
The following operations are performed (excluding some
versions for specific markets):
❍the direction indicators flash twice;
❍two brief acoustic signals are emitted (“BEEP”);
❍the doors are unlocked.
IMPORTANT If the central door locking system is re-
leased using the metal insert of the key, the alarm is not
disabled.
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 42