2010 JEEP GRAND CHEROKEE driver seat adjustment

UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CONTENTS
Mirrors .............................. 80
▫ Automatic Dimming Mirror .............. 80
▫ Outside Mirrors ...................... 81
▫ Outside Mirrors Folding Feature .......... 81
▫ Driver’s Automatic Dimming Mirrors — If
Equipped ........................... 81
▫ Power Outside Mirrors ................. 82
▫ Heated Mirrors — If Equipped ............ 82
▫ Illuminated Vanity Mirrors — If Equipped . . . 83 
Uconnect™ phone — If Equipped ........... 83
 Voice Command — If Equipped ............ 83
 Seats ............................... 83
▫ Front Manual Seat Adjustment ............ 84
▫ Front Seat Adjustment — Recline .......... 84
▫ Manual Lumbar Support Adjustment ....... 85
▫ Eight-Way Driver’s Power Seat ............ 85
▫ Four-Way Passenger’s Power Seat — If
Equipped ........................... 86
3

Manual Lumbar Support Adjustment
The manual lumbar support adjustment lever is located
on the right side of the driver’s seatback (all models) and
on the left side of the passenger’s seatback (if equipped).
Moving the lumbar control lever forward and rearward
will increase or decrease the lumbar support.
Eight-Way Driver’s Power Seat
The driver’s power seat switches are located on the
outboard side of the driver’s seat. The bottom switch
controls up/down, forward/rearward and tilt adjust-
ment. The top switch controls the seatback recline adjust-
ment.
Manual Lumbar ControlPower Seat Switches
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85

2. Press and release MEMORY button number 1. The
system will recall any memory settings stored in position
1. Wait for the system to complete the memory recall
before continuing to Step 3.
3. Press and release the memory S (SET) button located
on the driver’s door.
4. Within five seconds, press and release MEMORY
button 1 on the driver’s door.
5. Within five seconds, press and release the UNLOCK
button on the RKE transmitter.
To disable another RKE transmitter linked to either
memory position, repeat steps 1 through 5 for each RKE
transmitter.
NOTE:Once programmed, all RKE transmitters linked
to memory can be easily enabled or disabled at one time.
Refer to “Electronic Vehicle Information Center (EVIC)/
Customer-Programmable Features” in “Understanding
Your Instrument Panel” for further information.Easy Entry/Exit Seat
This feature provides automatic driver’s seat positioning
which will enhance driver mobility out of and into the
vehicle.
There are two possible Easy Entry/Exit adjustments
available:
•The seat cushion will move rearward approximately
2.5 in (60 mm), if the starting position of the seat is
greater than or equal to 2.67 in (68 mm) forward of the
rear seat stop when the key is removed from the
ignition switch. The seat will then move forward
approximately 2.5 in (60 mm) when the key is placed
into the ignition and turned out of the LOCK position.
•The seat will move to the position located 0.3 in
(8 mm) forward of the rear stop if the starting position
is between 0.9 to 2.67 in (23 to 68 mm) forward of the
rear stop when the key is removed from the ignition
switch. The seat will move forward to the memory/
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97

NOTE:The numbers on the temperature dial represent
a comfort setting when the Mode knob is set to AUTO,
and not the actual air temperature.
Turn the mode control (on the right) knob to AUTO, and
then turn the blower control (on the left) knob to either
LO AUTO or HI AUTO. The LO AUTO position should
be used for front seat occupants only. The HI AUTO
position should be used when more airflow is desired, or
when rear seat occupants are present. Dial in the comfort
setting you would like the system to maintain by rotating
the driver’s or passenger’s control knob. Once the com-
fort level is selected, the system will maintain that level
automatically using the heating system. Should the de-
sired comfort level require air conditioning, the system
will automatically make the adjustment. You will experience the greatest efficiency by simply
allowing the system to function automatically. Selecting
the OFF (O) position on the blower control knob stops the
system completely.
NOTE:
The temperature setting can be adjusted at any
time without affecting automatic control operation. How-
ever, if the driver and/or passenger temperature knobs
are set to the full hot or full cold positions, the air
temperature out of the ducts will be full hot or full cold
respectively. With the temperature setting in these posi-
tions, the system does not attempt automatic comfort
control.
The air conditioning in this system is au-
tomatic. Pressing this button while in
AUTO mode will cause the LED to flash
three times and remain off. This indicates
that the system is in AUTO and requesting the air
conditioning is not necessary.
Air
Conditioning
226 UNDERSTANDING YOUR INSTRUMENT PANEL