2010 JEEP GRAND CHEROKEE driver seat adjustment

UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CONTENTS
Mirrors .............................. 80
▫ Inside Day/Night Mirror ................ 80
▫ Automatic Dimming Mirror — If Equipped . . . 81
▫ Outside Mirrors ...................... 81
▫ Outside Mirrors Folding Feature .......... 82
▫ Driver’s Automatic Dimming Mirrors —
If Equipped ......................... 82
▫ Outside Power Mirrors ................. 82
▫ Heated Mirrors — If Equipped ............ 83▫
Illuminated Vanity Mirrors — If Equipped . . . 84
▫ Sun Visor Extension — If Equipped ........ 84
 Uconnect™ phone — If Equipped ........... 84
 Voice Command — If Equipped ............ 84
 Seats ............................... 84
▫ Front Manual Seat Adjustment ............ 85
▫ Front Seat Adjustment — Recline .......... 85
▫ Manual Lumbar Support Adjustment ....... 86
▫ Eight-Way Driver’s Power Seat ............ 87
3

WARNING!
Do not ride with the seatback reclined so that the seat
belt is no longer resting against your chest. In a
collision, you could slide under the seat belt and be
seriously or even fatally injured. Use the recliner
only when the vehicle is parked.
Manual Lumbar Support Adjustment
The manual lumbar support adjustment lever is located
on the right side of the driver’s seatback (all models) and
on the left side of the passenger’s seatback (if equipped).
Moving the lumbar control lever forward and rearward
will increase or decrease the lumbar support.
Manual Lumbar Control
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Eight-Way Driver’s Power Seat
The driver’s power seat switches are located on the out-
board side of the driver’s seat. The bottom switch controls
up/down, forward/rearward and tilt adjustment. The top
switch controls the seatback recline adjustment.WARNING!
Adjusting a seat while the vehicle is moving is
dangerous. The sudden movement of the seat could
cause you to lose control. The seat belt might not be
properly adjusted and you could be injured. Adjust
any seat only while the vehicle is parked.
CAUTION!
DO NOT place any article under a power seat or
impede its ability to move as it may cause damage to
the seat controls. Seat travel may become limited if
movement is stopped by an obstruction in the seat’s
path.
Power Seat Switches
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87

Easy Entry/Exit Seat
This feature provides automatic driver’s seat positioning
which will enhance driver mobility out of and into the
vehicle.
There are two possible Easy Entry/Exit adjustments
available:
•The seat cushion will move rearward approximately
2.5 in (60 mm), if the starting position of the seat is
greater than or equal to 2.67 in (68 mm) forward of the
rear seat stop when the key is removed from the
ignition switch. The seat will then move forward
approximately 2.5 in (60 mm) when the key is placed
into the ignition and turned out of the LOCK position.
•The seat will move to the position located 0.3 in
(8 mm) forward of the rear stop if the starting position
is between 0.9 to 2.67 in (23 to 68 mm) forward of the
rear stop when the key is removed from the ignition
switch. The seat will move forward to the memory/driving position when the key is placed into the
ignition, and turned out of the LOCK position toward
the ACC/ON position.
The Easy Entry/Exit feature will be automatically dis-
abled if the seat is already positioned closer than 0.9 in
(23 mm) forward of the rear stop. At this position, there
is no benefit to the driver by moving the seat for Easy
Exit/Entry.
Each stored memory setting will have an associated Easy
Entry/Exit position.
NOTE: The Easy Entry/Exit feature is not enabled
when the vehicle is delivered from the factory. The Easy
Entry/Exit feature is enabled (or later disabled) through
the programmable features in the Electronic Vehicle
Information Center (EVIC). Refer to “Electronic Vehicle
Information Center (EVIC)/Customer-Programmable
Features” in “Understanding Your Instrument Panel” for
further information.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99

NOTE:The numbers on the temperature dial represent
a comfort setting when the Mode knob is set to AUTO,
and not the actual air temperature.
Turn the mode control (on the right) knob to AUTO, and
then turn the blower control (on the left) knob to either
LO AUTO or HI AUTO. The LO AUTO position should be used for front seat occupants only. The HI AUTO
position should be used when more airflow is desired, or
when rear seat occupants are present. Dial in the comfort
setting you would like the system to maintain by rotating
the driver’s or passenger’s control knob. Once the com-
fort level is selected, the system will maintain that level
automatically using the heating system. Should the de-
sired comfort level require air conditioning, the system
will automatically make the adjustment.
You will experience the greatest efficiency by simply
allowing the system to function automatically. Selecting
the OFF (O) position on the blower control knob stops the
system completely.
NOTE:
The temperature setting can be adjusted at any
time without affecting automatic control operation. How-
ever, if the driver and/or passenger temperature knobs
are set to the full hot or full cold positions, the air
temperature out of the ducts will be full hot or full cold
Automatic Temperature Controls
4
UNDERSTANDING YOUR INSTRUMENT PANEL 225