2010 JEEP GRAND CHEROKEE engine

Ethanol
The manufacturer recommends that your ve-
hicle be operated on fuel containing no more
than 10% Ethanol. Purchasing your fuel from a
reputable supplier may reduce the risk of ex-
ceeding this 10% limit and/or of receiving fuel
with abnormal properties. It should also be
noted that an increase in fuel consumption
should be expected when using Ethanol-
blended fuels, due to the lower energy content
of Ethanol.
Problems that result from using Methanol/
gasoline or E85 Ethanol blends are not the
responsibility of the manufacturer. While MTBE
is an oxygenate made from Methanol, it does
not have the negative effects of Methanol.
CAUTION!
Use of fuel with Ethanol content higher than
10% may result in engine malfunction, starting
and operating difficulties and materials degra-
dation. These adverse effects could result in
permanent damage to your vehicle.Clean Air Gasoline
Many gasolines are now being blended that
contribute to cleaner air, especially in those
areas where air pollution levels are high. These
new blends provide a cleaner burning fuel and
some are referred to as “reformulated gaso-
line.”
The manufacturer supports these efforts toward
cleaner air. You can help by using these blends
as they become available.
MMT in Gasoline
MMT is a manganese containing metallic addi-
tive that is blended into some gasoline to
increase octane. Gasoline blended with MMT
provides no performance advantage beyond
gasoline of the same octane number without
MMT. Gasoline blended with MMT reduces
spark plug life and reduces emission system
performance in some vehicles. The manufac-
turer recommends that gasoline without MMT
be used in your vehicle. The MMT content of
gasoline may not be indicated on the gasoline
pump; therefore, you should ask your gasoline
retailer whether or not his/her gasoline contains
MMT. Materials Added to Fuel
Besides using unleaded gasoline with the
proper octane rating, gasolines that contain
detergents, corrosion and stability additives
are recommended. Using gasolines that have
these additives will help improve fuel economy,
reduce emissions, and maintain vehicle perfor-
mance.
Indiscriminate use of fuel system cleaning
agents should be avoided. Many of these ma-
terials intended for gum and varnish removal
may contain active solvents or similar ingredi-
ents. These can harm fuel system gasket and
diaphragm materials.
WARNING!
Carbon monoxide (CO) in exhaust gases is
deadly. Follow the precautions below to pre-
vent carbon monoxide poisoning:
(Continued)
241

WARNING!(Continued)
• Do not inhale exhaust gases. They contain
carbon monoxide, a colorless and odorless
gas which can kill. Never run the engine in
a closed area, such as a garage, and never
sit in a parked vehicle with the engine
running for an extended period. If the ve-
hicle is stopped in an open area with the
engine running for more than a short pe-
riod, adjust the ventilation system to force
fresh, outside air into the vehicle.
• Guard against carbon monoxide with
proper maintenance. Have the exhaust
system inspected every time the vehicle is
raised. Have any abnormal conditions re-
paired promptly. Until repaired, drive with
all side windows fully open.
• Keep the liftgate closed when driving your
vehicle to prevent carbon monoxide and
other poisonous exhaust gases from enter-
ing the vehicle.FUEL REQUIREMENTS — DIESEL
ENGINE
Use good quality diesel fuel from a reputable
supplier. For most year-round service, No. 2
diesel fuel, meeting ASTM specification D-975
Grade S15, will provide good performance. If
the vehicle is exposed to extreme cold (below
20° F or -7° C), or is required to operate at
colder-than-normal conditions for prolonged
periods, use climatized No. 2 diesel fuel or
dilute the No. 2 diesel fuel with 50% No. 1
diesel fuel. This will provide better protection
from fuel gelling or wax-plugging of the fuel
filters. This vehicle must only use premium
diesel fuel that meets the requirements of
EN 590. Biodiesel blends that meet EN 590
may also be used.
CAUTION!
The manufacturer requires that you must fuel
this vehicle with Ultra Low Sulfur Highway
Diesel fuel (15 ppm Sulfur maximum) and
prohibits the use of Low Sulfur Highway Die-
sel fuel (500 ppm Sulfur maximum) to avoid
damage to the emissions control system.
WARNING!
Do not use alcohol or gasoline as a fuel-
blending agent. They can be unstable under
certain conditions and hazardous or explosive
when mixed with diesel fuel.
Diesel fuel is seldom completely free of water.
To prevent fuel system trouble, drain the accu-
mulated water from the fuel/water separator
using the provided fuel/water separator drain. If
you buy good quality fuel and follow the cold
weather advice above, fuel conditioners should
not be required in your vehicle. If available in
your area, a high cetane “premium” diesel fuel
may offer improved cold-starting and warm-up
performance.
ADDING FUEL
Fuel Filler Cap (Gas Cap)
The gas cap is located behind the locking fuel
filler door, on the driver’s side of the vehicle. If
the gas cap is lost or damaged, be sure the
replacement cap is for use with this vehicle.
1. Press the fuel filler door release switch (lo-
cated under the headlamp switch).
242

2. Open the fuel filler door, and remove the fuel
filler cap.
CAUTION!
•Damage to the fuel system or emission
control system could result from using an
improper fuel cap (gas cap). A poorly fitting
cap could let impurities into the fuel system.
Also, a poorly fitting aftermarket cap can
cause the “Malfunction Indicator Light
(MIL)” to illuminate, due to fuel vapors
escaping from the system.
• A poorly fitting gas cap may cause the MIL
to turn on.
• To avoid fuel spillage and overfilling, do not
“top off” the fuel tank after filling.
WARNING!
• Never have any smoking materials lit in or
near the vehicle when the gas cap is re-
moved or the tank is being filled.
• Never add fuel when the engine is running.
This is in violation of most state and federal
fire regulations and may cause the mal-
function indicator light to turn on.
(Continued)
WARNING!(Continued)
• A fire may result if gasoline is pumped into
a portable container that is inside of a
vehicle. You could be burned. Always place
gas containers on the ground while filling.
NOTE:
• When the fuel nozzle “clicks” or shuts off,
the fuel tank is full.
• Tighten the gas cap about one-quarter
turn until you hear one click. This is an
indication that the cap is properly tight-
ened.
• If the gas cap is not tighten properly, the
MIL will come on. Be sure the gas cap is
tightened every time the vehicle is refu-
eled.
Emergency Fuel Filler Door Release
If you are unable to open the fuel filler door, use
the fuel filler door emergency release.
1. Open the liftgate.
2. Remove the left rear storage bin cover.
3. Pull the release cable.
Fuel Filler Door Release Switch
Fuel Filler Cap
243

Trailer Towing Weights (Maximum Trailer Weight Ratings)The following chart provides the maximum trailer weight ratings towable for your given drivetrain.
Engine/Transmission Max. GTW (Gross Trailer Wt.) — withTrailer BrakeMax. GTW (Gross Trailer Wt.) —
without Trailer Brake Tongue Wt. (See Note)
3.6L Gasoline 5,000 lbs (2 268 kg) 1,653 lbs (750 kg) 249 lbs (113 kg)
5.7L Gasoline 7,716 lbs (3 500 kg) 1,653 lbs (750 kg) 386 lbs (175 kg) 3.0L Diesel 7,716 lbs (3 500 kg) 1,653 lbs (750 kg) 386 lbs (175 kg)
Maximum trailer towing speed is limited to 62 mph (100 km/h) unless local laws require a lower speed.
NOTE:
The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight
referenced on the Tire and Loading Information placard. Refer to “Tires – General Information” in “Starting and Operating” for further information.
Trailer And Trailer Tongue WeightAlways load a trailer with 60% of the weight in
the front of the trailer. Loads balanced over the
wheels, or heavier in the rear, can cause the
trailer to sway severelyside-to-side which will
cause loss of control of vehicle and trailer.
Failure to load trailers heavier in front is the
cause of many trailer accidents. Never exceed
the maximum tongue weight stamped on your
trailer hitch. Consider the following items when computing
the weight on the front/rear axles of the vehicle:
•
The trailer tongue weight of the trailer.
• The weight of any other type of cargo or
equipment put in or on your vehicle.
• The weight of the driver and all passengers.
NOTE:
Remember that everything put into or on the
trailer adds to the load on your vehicle. Also,
additional factory-installed options, or au-
246

thorized dealer-installed options, must be
considered as part of the total load on your
vehicle.
Towing RequirementsTo promote proper break-in of your new vehicle
drivetrain components, the following guidelines
are recommended.
CAUTION!
•Do not tow a trailer at all during the first
500 miles (805 km) the new vehicle is
driven. The engine, axle or other parts
could be damaged.
• Then, during the first 500 miles (805 km)
that a trailer is towed, do not drive over
50 mph (80 km/h) and do not make starts at
full throttle. This helps the engine and other
parts of the vehicle wear in at the heavier
loads.
Perform the maintenance listed in the “Mainte-
nance Schedule.” Refer to “Maintenance
Schedule” for the proper maintenance inter-
vals. When towing a trailer, never exceed the
GAWR or GCWR ratings.
WARNING!
Improper towing can lead to an injury acci-
dent. Follow these guidelines to make your
trailer towing as safe as possible:
•
Make certain that the load is secured in the
trailer and will not shift during travel. When
trailering cargo that is not fully secured, dy-
namic load shifts can occur that may be
difficult for the driver to control. You could lose
control of your vehicle and have an accident.
• When hauling cargo or towing a trailer, do
not overload your vehicle or trailer. Over-
loading can cause a loss of control, poor
performance or damage to brakes, axle,
engine, transmission, steering, suspen-
sion, chassis structure or tires.
• Safety chains must always be used be-
tween your vehicle and trailer. Always con-
nect the chains to the hook retainers of the
vehicle hitch. Cross the chains under the
trailer tongue and allow enough slack for
turning corners.
(Continued)
WARNING!(Continued)
• Vehicles with trailers should not be parked
on a grade. When parking, apply the park-
ing brake on the tow vehicle. Put the tow
vehicle transmission in PARK. For four-
wheel drive vehicles, make sure the trans-
fer case is not in NEUTRAL. Always, block
or chock the trailer wheels.
• GCWR must not be exceeded.
• Total weight must be distributed be-
tween the tow vehicle and the trailer
such that the following four ratings are
not exceeded:
1. GVWR
2. GTW
3. GAWR
4. Trailer tongue weight rating for the trailer
hitch utilized.
Towing Requirements – Tires
Proper tire inflation pressures are essential to the safe and satisfactory operation of your
vehicle. Refer to “Tires – General Informa-
tion” in “Starting and Operating” for proper
tire inflation procedures.
247

sive shifting and heat buildup. This action
will also provide better engine braking.
The transmission fluid and filter should be
changed if you REGULARLY tow a trailer for
more than 45 minutes of continuous operation.
Refer to “Maintenance Schedule” for the proper
maintenance intervals.
NOTE:
Check the transmission fluid level before
towing (5.7L engine).
To help maintain a comfortable operating
temperature for your transmission, it is rec-
ommended that when towing a maximum
loaded trailer up steep grades with switch
backs, you should use the ERS function on
the transmission shifter to lock your vehicle
into first gear (5.7L Models Only).
Electronic Speed Control – If Equipped
Do not use in hilly terrain or with heavy loads.
When using the speed control, if you expe-rience speed drops greater than 10 mph
(16 km/h), disengage until you can get back
to cruising speed. Use speed control in flat terrain and with light
loads to maximize fuel efficiency.
Cooling System
To reduce potential for engine and transmission
overheating, take the following actions:
City Driving
When stopped for short periods of time, shift
the transmission into NEUTRAL and increase
engine idle speed.
Highway Driving
Reduce speed.
Air Conditioning
Turn off temporarily.
Trailer Hitch Attaching Points
Your vehicle will require extra equipment to tow
a trailer safely and efficiently. The trailer tow
hitch must be attached to your vehicle using
the provided attaching points on the vehicle’s
frame. Refer to the following chart to determine
the accurate attaching points. Other equip-
ment, such as trailer sway controls and braking
equipment, trailer equalizing (leveling) equip-
ment and low profile mirrors, may also be
required or strongly recommended.
Trailer Tow Hitch Attaching Points And Overhang Dimensions
Fixed, Detach
and Retractable Hitch
A 1.85 ft. (565 mm)
B 2.09 ft. (636 mm)
C 2.32 ft. (707 mm)
D 2.4 ft. (733 mm)
E 1.62 ft. (494 mm)
F 1.47 ft. (447 mm)
G (Maximum Overhang) 3.59 ft. (1093 mm)
250

RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)
Towing This Vehicle Behind Another Vehicle
Towing Condition Wheel OFF the Ground Four-Wheel Drive ModelsFlat Tow NONE See Instructions
•
Transmission in PARK
• Transfer case in NEUTRAL (N)
• Tow in forward direction
Dolly Tow Front
NOT ALLOWED
Rear NOT ALLOWED
On Trailer ALL OK
NOTE:
Vehicles equipped with Quadra-Lift™ must be lowered to the “Park” (lowest) level, and have automatic leveling disabled, before tying them
down (from the body) on a trailer or flatbed truck. Refer to “Quadra-Lift™ – If Equipped” in “Starting and Operating” for more information. If the
vehicle cannot be lowered to the “Park” level (for example, engine will not run), tie-downs must be fastened to the axles (not to the body). Failure to follow these instructions may cause fault codes to be set and/or loss of proper tie-down tension.
251

2. Turn OFF the ignition.
3. For vehicles with Keyless Enter-N-Go, re-
move the Keyless Enter-N-Go button and use
the key fob to complete this procedure. Refer to
“Starting Procedures/Keyless Enter-N-Go” in
“Starting and Operating” for further information.
4. Turn the ignition switch to the ON/RUN po-
sition, but do not start the engine.
5. Press and hold the brake pedal.
6. Shift the transmission into NEUTRAL.
7. Using the point of a ballpoint pen or similar
object, press and hold the recessed transfer
case N (Neutral) button (located by the selector
switch) for four seconds, until the light behind
the N symbol starts to blink, indicating shift in
progress. The light will stop blinking (stay on
solid) when the shift to N (Neutral) is complete.
A “FOUR WHEEL DRIVE SYSTEM IN NEU-
TRAL” message will display on the EVIC (Elec-
tronic Vehicle Information Center). Refer to
“Electronic Vehicle Information Center (EVIC)”
in “Understanding Your Instrument Panel” for
further information.8. Start the engine.
9. Shift the transmission into REVERSE.
10. Release the brake pedal for five seconds
and ensure that there is no vehicle movement.
11. Turn OFF the engine and leave the ignition
switch in the unlocked OFF position.
12. Firmly apply the parking brake.
13. Shift the transmission into PARK.CAUTION!
Damage to the transmission may occur if the
transmission is shifted into PARK with the
transfer case in NEUTRAL (N) and the engine
running. With the transfer case in NEUTRAL
(N) ensure that the engine is off prior to
shifting the transmission into PARK.
14. Attach the vehicle to the tow vehicle using
a suitable tow bar.
15. Release the parking brake.
16. Disconnect the negative battery cable, and
secure it away from the negative battery post.
NOTE:
• Steps 1 through 6 are requirements that
must be met prior to pressing the NEU-
TRAL (N) button, and must continue to be
met until the four seconds elapse and the
shift has been completed. If any of these
requirements are not met prior to press-
ing the NEUTRAL (N) button or are no
longer met during the four second timer,
then the NEUTRAL (N) indicator light will
Neutral Switch
253