2010 JEEP GRAND CHEROKEE ignition

uses six sensors located in the front bumper
fascia to scan for obstacles up to 47 in
(120 cm) away from the front bumper fascia.
The warning display located above in the In-
strument Cluster’s EVIC provides both visible
and audible warnings to indicate the range of
the object.
Service the ParkSensePark Assist
System
When the ParkSense Park Assist System is
malfunctioning, the instrument cluster will actu-
ate a single chime, once per ignition cycle. The
instrument cluster will display the “REAR SEN-
SOR BLINDED” message when any of the rear
sensor(s) is blocked by snow, mud, or ice and
the vehicle is shifted into REVERSE or DRIVE.
The instrument cluster will display the “CLEAN
PARK ASSIST SENSORS” message when any
of the front sensor(s) is blocked by snow, mud,
or ice and the vehicle is shifted into REVERSE
or DRIVE. The instrument cluster will display the
“SERVICE PARK ASSIST SYSTEM” message
when any of the rear or front sensors are
damaged and require service. When the shift
lever is moved to REVERSE or DRIVE and the system has detected a faulted condition, the
EVIC will display the “CLEAN PARK ASSIST
SENSORS” or the “SERVICE PARK ASSIST
SYSTEM” message for as long as the vehicle is
in REVERSE or DRIVE (at speeds less than
11 mph/18 km/h). Under this condition Park-
Sense
will not operate. Refer to “Electronic
Vehicle Information Center (EVIC)” in “Under-
standing Your Instrument Panel” for further in-
formation.
If the “CLEAN PARK ASSIST SENSORS” mes-
sage appears in the Electronic Vehicle Informa-
tion Center (EVIC) and the rear fascia/bumper
or front fascia/bumper is clean and clear of
snow, ice, mud, dirt or other obstruction, see
your authorized dealer. If “SERVICE PARK AS-
SIST SYSTEM” appears in the EVIC, see your
authorized dealer.
Cleaning the ParkSense SystemClean the ParkSense sensors with water, car
wash soap and a soft cloth. Do not use rough or
hard cloths. Do not scratch or poke the sen-
sors. Otherwise, you could damage the sen-
sors.
ParkSense System Usage
Precautions
NOTE:
• Ensure that the front and rear bumper are
free of snow, ice, mud, dirt and debris to
keep the ParkSense system operating
properly.
• Jackhammers, large trucks, and other vi-
brations could affect the performance of
ParkSense .
• When you turn ParkSense off, the instru-
ment cluster will display “PARK ASSIST
OFF.” Furthermore, once you turn Park-
Sense off, it remains off until you turn it
on again, even if you cycle the ignition
key.
• When you move the shift lever to the
REVERSE or DRIVE position and Park-
Sense is turned off, the instrument clus-
ter will display “PARK ASSIST OFF” mes-
sage for as long as the vehicle is in
REVERSE and when the vehicle is in
DRIVE at or below 11 mph (18 km/h).
• ParkSense , when on, will MUTE the radio
when it is sounding a tone.
136

Courtesy/Reading LightsLocated on the overhead console are two
courtesy/reading lights. Press the lens to turn
these lights on. Press a second time to turn the
lights off.
The lights also turn on when a front door or rear
door is opened, when the UNLOCK button on
the Remote Keyless Entry (RKE) transmitter is
pressed, or when the dimmer wheel is moved
up to the dome ON position.Sunglasses StorageAt the rear of the console a compartment is
provided for the storage of a pair of sun-
glasses.
The storage compartment access is a “push/
push” design. Push the chrome pad on the
door to open. Push the chrome pad on the door
to close.POWER SUNROOF — IF EQUIPPEDThe power sunroof switch is located between
the sun visors on the overhead console.
WARNING!
•Never leave children in a vehicle with the
key in the ignition switch. Occupants, par-
ticularly unattended children, can become
entrapped by the power sunroof while op-
erating the power sunroof switch. Such
entrapment may result in serious injury or
death.
(Continued)Courtesy/Reading Lights
Sunglass Storage
Power Sunroof Switch
140

open, adjust the sunroof opening to minimize
the buffeting or open any window.
Sunroof MaintenanceUse only a nonabrasive cleaner and a soft cloth
to clean the glass panel.
Ignition OFF OperationThe power sunroof switches remain active for
up approximately ten minutes after the ignition
switch has been turned OFF. Opening either
front door will cancel this feature.
COMMAND VIEW SUNROOF WITH
POWER SHADE — IF EQUIPPED
The command view sunroof switch is located to
the left between the sun visors on the overhead
console.
The power shade switch is located to the right
between the sun visors on the overhead con-
sole.WARNING!
•Never leave children in a vehicle with the
key in the ignition switch. Occupants, par-
ticularly unattended children, can become
entrapped by the power sunroof while op-
erating the power sunroof switch. Such
entrapment may result in serious injury or
death.
(Continued)
WARNING!(Continued)
• In a collision, there is a greater risk of being
thrown from a vehicle with an open sunroof.
You could also be seriously injured or killed.
Always fasten your seat belt properly and
make sure all passengers are properly se-
cured too.
• Do not allow small children to operate the
sunroof. Never allow your fingers, other
body parts, or any object to project through
the sunroof opening. Injury may result.
Opening Sunroof – ExpressPress the sunroof switch rearward for less than
one second and release, and the sunroof glass
will automatically slide fully open from any
position, then stop. This is called “Express
Open”. During Express Open operation, any
sunroof switch press or shade switch press will
stop the sunroof. If the shade is closed when
the sunroof switch is pressed, the shade will
automatically move to the middle position be-
fore the sunroof begins Express Open opera-
tion.
Command View Sunroof and Power Shade Switches
142

Method 2:If three consecutive sunroof or
shade close attempts result in Pinch Protect
reversals, the fourth close attempt will be a
Manual Close movement with Pinch Protect
disabled.
Pinch Protect Override CancellationOnce the sunroof or shade reaches the closed
position, Pinch Protect will reactivate. In addi-
tion, if any other switch is pressed which moves
the sunroof or shade away from the closed
position, Pinch Protect will reactivate.
Wind BuffetingWind buffeting can be described as the per-
ception of pressure on the ears or a helicopter-
type sound in the ears. Your vehicle may exhibit
wind buffeting with the windows down, or the
sunroof (if equipped) in certain open or partially
open positions. This is a normal occurrence
and can be minimized. If the buffeting occurs
with the rear windows open, open the front and
rear windows together to minimize the buffet-
ing. If the buffeting occurs with the sunroof
open, adjust the sunroof opening to minimize
the buffeting or open any window.
Sunroof MaintenanceUse only a non-abrasive cleaner and a soft
cloth to clean the glass panel.
Ignition OFF OperationThe power sunroof switches can be pro-
grammed to remain active for up to approxi-
mately ten minutes after the ignition switch has
been turned OFF. Refer to “Electronic Vehicle
Information Center (EVIC)/Customer-Program-
mable Features (System Setup)” under “Under-
standing Your Instrument Panel” for further in-
formation.
NOTE:
Opening either front door will cancel this
feature.
Sunroof Fully ClosedPress the switch forward and release to ensure
that the sunroof is fully closed.
ELECTRICAL POWER OUTLETSYour vehicle is equipped with 12 Volt (13 Amp)
power outlets that can be used to power cellu-
lar phones, small electronics and other low
powered electrical accessories. The power out-
lets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is powered.
Power outlets labeled with a “key” are powered
when the ignition switch is in the ON or ACC
position, while the outlets labeled with a “bat-
tery” are connected directly to the battery and
powered at all times.
NOTE:
•
All accessories connected to the “bat-
tery” powered outlets should be removed
or turned off when the vehicle is not in
use to protect the battery against dis-
charge.
• To ensure proper operation a MOPAR 
knob and element must be used.
• Do not exceed the maximum power of 160
Watts (13 Amps) at 12 Volts. If the 160 Watt
(13 Amp) power rating is exceeded the
fuse protecting the system will need to be
replaced.
The front power outlet is located inside the
storage area on the center stack of the instru-
ment panel. Push inward on the storage lid to
open the compartment and gain access to this
power outlet.
144

WARNING!(Continued)
• Cargo tie-down hooks are not safe anchors
for a child seat tether strap. In a sudden
stop or accident, a hook could pull loose
and allow the child seat to come loose. A
child could be badly injured. Use only the
anchors provided for child seat tethers.
The weight and position of cargo and passen-
gers can change the vehicle center of gravity
and vehicle handling. To avoid loss of control
resulting in personal injury, follow these guide-
lines for loading your vehicle:
• Do not carry loads which exceed the load
limits described on the label attached to the
left door or left door center pillar.
• Always place cargo evenly on the cargo
floor. Put heavier objects as low and as far
forward as possible.
• Place as much cargo as possible in front of
the rear axle. Too much weight or improp-
erly placed weight over or behind the rear
axle can cause the rear of the vehicle to
sway.
(Continued)WARNING!(Continued)
• Do not pile luggage or cargo higher than
the top of the seatback. This could impair
visibility or become a dangerous projectile
in a sudden stop or accident.
REAR WINDOW FEATURES
Rear Window Wiper/Washer
The rear wiper/washer is controlled by a rotary
switch located on the control lever. The control
lever is located on the left side of the steering
column. Rotate the center portion of the lever
upward to the first detent for intermittent
operation and to the second detent for
continuous rear wiper operation.
Rotating the center portion upward
once more will activate the washer
pump which will continue to operate as
long as the switch is held. Upon release
of the switch, the wipers will resume the con-
tinuous rear wiper operation. When this rotary
control is in the OFF position, rotating it down-
ward will activate the rear washer pump which
will continue to operate as long as the switch is
held. Once the switch is released it will return to
the OFF position and the wipers will cycle two
times before returning to the parked position.
NOTE:
As a protective measure, the pump will stop
if the switch is held for more than 20 sec-
onds. Once the switch is released the pump
will resume normal operation.
If the rear wiper is operating when the ignition is
turned OFF, the wiper will automatically return
to the “park” position.
Rear Wiper/Washer Control
150

INSTRUMENT PANEL FEATURES
1 — Air Outlet 5 — Climate Controls 9 — Fuel Door Release
2 — Instrument Cluster 6 — Lower Switch Bank 10 — Headlight Switch
3 — Radio 7 — Storage Bin 11 — Hood Release
4 — Glove Compartment 8 — Ignition Switch
156

INSTRUMENT CLUSTER
DESCRIPTIONS
1. Tachometer
Indicates the engine speed in revolutions per
minute (RPM).
2. Airbag Warning Light
This light will turn on for four to eight
seconds as a bulb check when the
ignition switch is first turned to the
ON/RUN position. If the light is ei-
ther not on during starting, stays on,
or turns on while driving, then have
the system inspected at an authorized dealer as
soon as possible. Refer to “Occupant Re-
straints” in “Things To Know Before Starting Your
Vehicle” for further information.
3. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL)
is part of an onboard diagnostic sys-
tem called OBD II that monitors en-
gine and automatic transmission con-
trol systems. The light will illuminate
when the key is in the ON/RUN position before
engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the
condition checked promptly.
Certain conditions such as a loose or missing
gas cap, poor fuel quality, etc., may illuminate
the light after engine start. The vehicle should
be serviced if the light stays on through several
of your typical driving cycles. In most situa-
tions, the vehicle will drive normally and will not
require towing.
CAUTION!
Prolonged driving with the MIL on could cause
damage to the engine control system. It also
could affect fuel economy and drivability. If the
MIL is flashing, severe catalytic converter
damage and power loss will soon occur. Im-
mediate service is required.
WARNING!
A malfunctioning catalytic converter, as refer-
enced above, can reach higher temperatures
than in normal operating conditions. This can
cause a fire if you drive slowly or park over
flammable substances such as dry plants or
wood or cardboard, etc. This could result in
death or serious injury to the driver, occupants
or others.
4. Electronic Stability Control (ESC)
Activation/Malfunction Indicator Light —
If Equipped The “ESC Activation/Malfunction
Indicator Light” in the instrument
cluster will come on when the igni-
tion switch is turned to the ON/
RUN position. It should go out with
the engine running. If the “ESC
Activation/Malfunction Indicator Light” comes
on continuously with the engine running, a
malfunction has been detected in the ESC
system. If this light remains on after several
ignition cycles, and the vehicle has been driven
several miles (kilometers) at speeds greater
158

than 30 mph (48 km/h), see your authorized
dealer as soon as possible to have the problem
diagnosed and corrected.
NOTE:
•The “ESC Off Indicator Light” and the
“ESC Activation/Malfunction Indicator
Light” come on momentarily each time
the ignition switch is turned to ON/RUN.
• Each time the ignition is turned to ON/
RUN, the ESC system will be ON even if it
was turned off previously.
• The ESC system will make buzzing or
clicking sounds when it is active. This is
normal; the sounds will stop when ESC
becomes inactive following the maneuver
that caused the ESC activation.
5. TOW/HAUL Indicator Light —
If Equipped This light will illuminate when the
TOW/HAUL button has been se-
lected. The TOW/HAUL button is
located in the center of the instru-
ment panel (below the climate
controls). 6. Turn Signal Indicator
The arrows will flash with the exterior turn
signals when the turn signal lever is op-
erated. A tone will chime, and an EVIC
message will appear if the turn signals are left
on for more than 1 mile (1.6 km).
7. High Beam Indicator Indicates that headlights are on high
beam.
8. Front Fog Light Indicator — If Equipped This indicator will illuminate when the
front fog lights are on.
9. Hill Descent Control Indicator Light —
If Equipped The symbol indicates the status of
the Hill Decent Control (HDC) fea-
ture. The lamp will be on solid
when HDC is armed. HDC can
only be armed when the transfer
case is in the “4WD Low” position
and the vehicle speed is less then 30 mph
(48 km/h). If these conditions are not met while
attempting to use the HDC feature, the HDC
indicator lamp will flash on/off. 10. Electronic Vehicle Information Center
(EVIC) Display/Odometer Display
The odometer display shows the total distance
the vehicle has been driven.
Regulations require that upon transfer of ve-
hicle ownership, the seller certify to the pur-
chaser the correct mileage that the vehicle has
been driven. If your odometer needs to be
repaired or serviced, the repair technician
should leave the odometer reading the same as
it was before the repair or service. If s/he
cannot do so, then the odometer must be set at
zero, and a sticker must be placed in the door
jamb stating what the mileage was before the
repair or service. It is a good idea for you to
make a record of the odometer reading before
the repair/service, so that you can be sure that
it is properly reset, or that the door jamb sticker
is accurate if the odometer must be reset at
zero.
When the appropriate conditions exist, this
display shows the Electronic Vehicle Informa-
tion Center (EVIC) messages. Refer to “Elec-
tronic Vehicle Information Center”.
159