2010 JEEP GRAND CHEROKEE buttons

The FUEL SAVER MODE message will display
above the average fuel economy in the EVIC
display. This message will appear whenever
MDS (if equipped) allows the engine to operate
on four cylinders, or if you are driving in a fuel
efficient manner.
This feature allows you to monitor when you are
driving in a fuel efficient manner, and it can be
used to modify driving habits in order to in-
crease fuel economy.
Distance To Empty (DTE)
Shows the estimated distance that can be
traveled with the fuel remaining in the tank. Thisestimated distance is determined by a
weighted average of the instantaneous and
average fuel economy, according to the current
fuel tank level. DTE cannot be reset through the
SELECT button.
NOTE:
Significant changes in driving style or ve-
hicle loading will greatly affect the actual
drivable distance of the vehicle, regardless
of the DTE displayed value.
When the DTE value is less than 30 miles
(48 km) estimated driving distance, the DTE
display will change to a “LOW FUEL” message.
This display will continue until the vehicle runs
out of fuel. Adding a significant amount of fuel
to the vehicle will turn off the “LOW FUEL”
message and a new DTE value will display.
Vehicle SpeedPress and release the UP or DOWN button until
“Vehicle Speed” displays highlighted in the
EVIC and press the SELECT button. Press the
SELECT button to display the current speed in
mph or km/h. Pressing the SELECT button a
second time will toggle the unit of measure
between mph or km/hNOTE:
Changing the unit of measure in the Vehicle
Speed menu will not change the unit of
measure in the EVIC.
Trip InfoPress and release the UP or DOWN button until
“Trip Info” displays highlighted in the EVIC and
press the SELECT button. Press and release
the UP/DOWN buttons until one of the following
Trip functions displays in the EVIC:
•
Trip A
• Trip B
• Elapsed Time
Press the UP/DOWN buttons to cycle through
all the Trip Computer functions.
The Trip Functions mode displays the following
information:
Trip A
Shows the total distance traveled for Trip A
since the last reset.
Trip B
Shows the total distance traveled for Trip B
since the last reset.
Fuel Saver Mode — On
172

Elapsed Time
Shows the total elapsed time of travel since the
last reset when the ignition switch is in the ACC
position. Elapsed time will increment when the
ignition switch is in the ON or START position.
To Reset The Display
Reset will only occur while a resettable function
is being displayed. Press and release the SE-
LECT button once to clear the resettable func-
tion being displayed. To reset all resettable
functions, press and hold the SELECT button
for two seconds. Current display will reset
along with other functions
UnitsPress and release the UP or DOWN button until
“Units” displays highlighted in the EVIC and
press the SELECT button. The EVIC, odometer,
and navigation system (if equipped) can be
changed between English and Metric units of
measure. To make your selection, scroll up or
down until the preferred setting is highlighted,
then press and release the SELECT button until
a check-mark appears next to the setting,
showing that setting has been selected.
Vehicle Info
(Customer Information Features)
Press and release the UP or DOWN button until
“SYSTEM” displays highlighted in the EVIC and
press the SELECT button. Press the UP and
DOWN button to scroll through the available
information displays, then press SELECT to
display anyone of the following choices.
•Coolant Temp
Displays the actual coolant temperature.
• Oil Temperature
Displays the actual oil temperature.
• Oil Pressure
Displays the actual oil pressure.
• Trans Temperature
Displays the actual transmission temperature.
• Engine Hours
Displays the hours of engine operation.
Tire PSI
Press and release the UP or DOWN button until
“Tire PSI” displays highlighted in the EVIC and
press the SELECT button. Press and release the UP/DOWN buttons until one of the following
System Status messages displays in the EVIC:
•
System OK
• System Warnings Displayed (will display all
currently active System Warnings)
• Tire Pressure Monitor System (shows the
current pressure of all four road tires). For
additional information, refer to “Tire Pressure
Monitor System” in “Starting And Operating”.Tire Pressure Display
173

entering and exiting the vehicle. To make your
selection, press and release the SELECT but-
ton until a check-mark appears next to the
feature showing the system has been activated
or the check-mark is removed, showing the
system has been deactivated.
NOTE:
The seat will return to the memorized seat
location (if Recall Memory with Remote Key
Unlock is set to ON) when the RKE transmit-
ter is used to unlock the door. Refer to
“Driver Memory Seat” in “Understanding
The Features Of Your Vehicle” for further
information.
Tilt Mirror in Reverse
When this feature is selected, the outside rear-
view mirrors will tilt downward when the ignition
switch is in the RUN position and the transmis-
sion is in the REVERSE position. The mirrors will
move back to their previous position when the
transmission is shifted out of REVERSE. To
make your selection, press and release the
SELECT button until a check-mark appears
next to the feature showing the system has
been activated or the check-mark is removed,
showing the system has been deactivated.Key-Off Power Delay
When this feature is selected, the power win-
dow switches, radio, hands-free system (if
equipped), DVD video system (if equipped),
power sunroof (if equipped), and power outlets
will remain active for up to 10 minutes after the
ignition switch is turned OFF. Opening a vehicle
door will cancel this feature. To make your
selection, scroll up or down until the preferred
setting is highlighted, then press and release
the SELECT button until a check-mark appears
next to the setting, showing that setting has
been selected.
Illuminated Approach
When this feature is selected, the headlights
will activate and remain on for 0, 30, 60, or
90 seconds when the doors are unlocked with
the RKE transmitter. To make your selection,
scroll up or down until the preferred setting is
highlighted, then press and release the SE-
LECT button until a check-mark appears next
to the setting, showing that setting has been
selected.
Display Fuel Saver— If Equipped
The “ECO” message is located in the
Compass/Temperature display, this message
can be turned on or off. To make your selection,
press and release the FUNCTION SELECT but-
ton until “ON” or “OFF” appears.
Keyless Enter-N-Go (Passive Entry)
This feature allows you to lock and unlock the
vehicle’s door(s) without having to press the
RKE transmitter lock or unlock buttons. To
make your selection, press and release the
SELECT button until a check-mark appears
next to the feature showing the system has
been activated or the check-mark is removed,
showing the system has been deactivated.
Refer to “Keyless Enter-N-Go” in “Things To
Know Before Starting Your Vehicle”.
Auto High Beams
(Available with SmartBeam™ Only)
When this feature is selected, the high beam
headlights will deactivate automatically under
certain conditions. To make your selection,
press and release the SELECT button until a
check-mark appears next to the feature show-
ing the system has been activated or the
check-mark is removed, showing the system
179

Display Units of Measure In:
The EVIC, odometer, and Uconnect™ gps (if
equipped) can be changed between English
and Metric units of measure. To make your
selection, press and release the SELECT but-
ton until “ENGLISH” or “METRIC” appears.
Calibrate Compass
Refer to “Compass Display” for more informa-
tion.
Compass Variance
Refer to “Compass Display” for more informa-
tion.
SOUND SYSTEMSRefer to your Sound Systems Booklet.
UNIVERSAL CONSUMER INTERFACE
(UCI) 1.0 — IF EQUIPPED
NOTE:
This section is for sales code RES and
REQ/REL/RET radios only with Uconnect™.
For sales code RER, REN, RBZ, REP, REW,
RB2 or REZ touch-screen radio UCI feature,
refer to the separate RER, REN, RBZ, RB2 orREZ User’s Manual. UCI is available only if
equipped as an option with these radios.
This feature allows an iPod
or external USB
device to be plugged into the USB port.
UCI supports Mini, 4G, Photo, Nano, 5G iPod 
and iPhone devices. Some iPod software
versions may not fully support the UCI features.
Please visit Apple’s website for software up-
dates.
NOTE:
• If the radio has a USB port, refer to the
appropriate Uconnect™ Multimedia radio
User’s Manual for iPod or external USB
device support capability.
• Connecting an iPod or consumer elec-
tronic audio device to the AUX port lo-
cated in the radio faceplate, plays media,
but does not use the UCI feature to con-
trol the connected device.
Connecting The iPod or External
USB Device
Once the audio device is connected and syn-
chronized to the vehicle’s UCI system (iPod 
device may take a few minutes to connect), the audio device starts charging and is ready for
use by pressing radio switches, as described
below.
NOTE:
If the audio device battery is completely
discharged, it may not communicate with
the UCI system until a minimum charge is
attained. Leaving the audio device con-
nected to the UCI system may charge it to
the required level.
Using This FeatureBy using iPod cable or external USB device to
connect to USB port:
•
The device audio can be played on the
vehicle’s sound system, providing metadata
(artist, track title, album, etc.) information on
the radio display.
• The audio device can be controlled using
the radio buttons to Play, Browse, and List
the iPod contents.
• The audio device battery charges when
plugged into the UCI connector (if supported
by the specific audio device)
181

Controlling The iPodor External
USB Device Using Radio Buttons
To get into the UCI (iPod or external USB
device) mode and access a connected audio
device, either press the “AUX” button on the
radio faceplate or press VR button and say
 USB or Switch to USB . Once in the UCI
mode, audio tracks (if available from audio
device) start playing over the vehicle’s audio
system.
Play ModeWhen switched to UCI mode, the iPod or
external USB device automatically starts Play
mode. In Play mode, the following buttons on
the radio faceplate may be used to control the
iPod or external USB device and display data:
• Use the TUNE control knob to select the next
or previous track.
• Turning it clockwise (forward) by one
click, while playing a track, skips to the
next track or press VR button and say
 Next Track . •
Turning it counterclockwise (backward)
by one click, will jump to the previous
track in the list or press VR button and say
 Previous Track 
• Jump backward in the current track by
pressing and holding the << RWbutton.
Holding the << RWbutton long enough
will jump to the beginning of the current
track.
• Jump forward in the current track by press-
ing and holding the FF>> button.
• A single press backward << RWor forward
FF >> will jump backward or forward re-
spectively, for five seconds.
• Use the << SEEKandSEEK >> buttons to
jump to the previous or next track. Pressing
the SEEK >> button during play mode will
jump to the next track in the list, or can press
VR button and say Next or Previous Track .
• While a track is playing, press the INFO
button to see the associated metadata (art-
ist, track title, album, etc.) for that track.
Pressing the INFObutton again jumps to the
next screen of data for that track. Once all screens have been viewed, the last
INFO
button press will go back to the play mode
screen on the radio.
• Pressing the REPEATbutton will change the
audio device mode to repeat the current
playing track or press the VR button and say
 Repeat ON or Repeat Off .
• Press the SCANbutton to use UCI device
scan mode, which will play the first 10 sec-
onds of each track in the current list and then
forward to the next song. To stop SCAN
mode and start playing the desired track,
when it is playing the track, press the SCAN
button again. During Scan mode, pressing
the << SEEKandSEEK >> buttons will
select the previous and next tracks.
• RND button (available on sales code RES
radio only): Pressing this button toggles be-
tween Shuffle ON and Shuffle OFF modes for
the iPod or external USB device, or press
VR button and say Shuffle ON or 
Shuffle
Off .Ifthe RNDicon is showing on the radio
display, then the shuffle mode is ON.
182

List Or Browse ModeDuring Play mode, pressing any of the buttons
described below, will bring up List mode. List
mode enables scrolling through the list of
menus and tracks on the audio device.
•TUNE control knob: The TUNEcontrol knob
functions in a similar manner as the scroll
wheel on the or external USB device.
• Turning it clockwise (forward) and coun-
terclockwise (backward) scrolls through
the lists, displaying the track detail on the
radio display. Once the track to be played
is highlighted on the radio display, press
the TUNE control knob to select and start
playing the track. Turning the TUNEcon-
trol knob fast will scroll through the list
faster. During fast scroll, a slight delay in
updating the information on the radio dis-
play may be noticeable.
• During all List modes, the iPod displays
all lists in “wrap-around” mode. So if the
track is at the bottom of the list, just turn
the wheel backwards (counter-clockwise)
to get to the track faster. •
In List mode, the radio PRESETbuttons
are used as shortcuts to the following lists
on the iPod or external USB device.
• Preset 1 – Playlists
• Preset2–Ar tists
• Preset 3 – Albums
• Preset 4 – Genres
• Preset 5 – Audiobooks
• Preset 6 – Podcasts
• Pressing a PRESET button will display the
current list on the top line and the first item
in that list on the second line.
• To Exit List mode without selecting a
track, press the same PRESETbutton
again to go back to Play mode.
• LIST button: The LISTbutton will display the
top level menu of the iPod or external USB
device. Turn the TUNEcontrol knob to list the
top-menu item to be selected and press the
TUNE control knob. This will display the next
sub-menu list item on the audio device, then
follow the same steps to go to the desired track in that list. Not all iPod
or external USB
device sub-menu levels are available on this
system.
• MUSIC TYPE button: TheMUSIC TYPE but-
ton is another shortcut button to the genre
listing on your audio device.
CAUTION!
• Leaving the iPod or external USB device
(or any supported device) anywhere in the
vehicle in extreme heat or cold can alter the
operation or damage the device. Follow the
device manufacturer’s guidelines.
• Placing items on the iPod or external USB
device, or connections to the iPod or
external USB device in the vehicle, can
cause damage to the device and/or to the
connectors.
WARNING!
Do not plug in or remove the iPod or external
USB device while driving. Failure to follow this
warning could result in an accident.
183

Bluetooth Streaming Audio (BTSA)Music can be streamed from your cellular
phone to the Uconnect™ phone system.
Controlling BTSA using Radio Buttons
To get into the BTSA mode, press either “AUX”
button on the radio or press VR button and say
“Bluetooth Streaming Audio”.
Play Mode
When switched to BTSA mode, some audio
devices can start playing music over the vehi-
cle’s audio system, but some devices require
the music to be initiated on the device first, then
it will get streamed to Uconnect™ phone sys-
tem. Seven devices can be paired to
Uconnect™ phone system, but just one can be
selected and played.
Selecting different Audio Device
1. Press PHONE button to begin.
2. After theReady prompt and the following
beep, say Setup , then Select Audio De-
vices .
3. Say name of the audio device or ask
Uconnect™ phone system to list audio de-
vices. Next Track
Use the SEEK UP button, or press the VR
button on the radio and say “Next Track” to
jump to the next track music on your cellular
phone.
Previous Track
Use the SEEK DOWN button, or press the VR
button on the radio and say “Previous Track” to
jump to the previous track music on your cel-
lular phone.
Browse
Browsing is not available on a BTSA device.
Only the current song that is playing will display
info.
STEERING WHEEL AUDIO
CONTROLS
The remote sound system controls are located
on the rear surface of the steering wheel.
Reach behind the wheel to access the
switches.
The right-hand control is a rocker-type switch
with a pushbutton in the center and controls the
volume and mode of the sound system. Press-
ing the top of the rocker switch will increase the
volume, and pressing the bottom of the rocker
switch will decrease the volume.
Pressing the center button will make the radio
switch between the various modes available
(AM/FM/SAT/CD/HDD/AUX/VES, etc.).
The left-hand control is a rocker-type switch
with a pushbutton in the center. The function of
Remote Sound System Controls
(Back View Of Steering Wheel)
184

Mode Control (Air Direction)
Push the mode control buttons to choose from
several patterns of air distribution.
PanelAir is directed through the outlets in the
instrument panel. These outlets can be
adjusted to direct airflow.
NOTE:
The center instrument panel outlets can be
aimed so that they are directed toward the
rear seat passengers for maximum airflow
to the rear.
Bi-Level Air is directed through the panel and
floor outlets.
NOTE:
For all settings except full cold or full hot,
there is a difference in temperature between
the upper and lower outlets. The warmer air
flows to the floor outlets. This feature gives
improved comfort during sunny but cool
conditions. Floor
Air is directed through the floor outlets
with a small amount flowing through the
defrost and side window demist outlets.
Mix Air is directed through the floor, defrost,
and side window demist outlets. This
setting works best in cold or snowy
conditions that require extra heat to the
windshield. This setting is good for maintaining
comfort while reducing moisture on the wind-
shield.
Defrost Air is directed through the windshield
and side window demist outlets. Use
this mode with maximum blower and
temperature settings for best windshield and
side window defrosting.
NOTE:
• In Floor, Mix and Defrost modes a small
amount of air will flow through the out-
board panel outlets for occupant comfort.
• The air conditioning compressor oper-
ates in Mix, Defrost, or a blend of these
modes, even if the Air Conditioning (A/C) button is not pressed. This dehumidifies
the air to help dry the windshield. To
improve fuel economy, use these modes
only when necessary.
Recirculation Control Pressing the Recirculation Control
button will put the system in recir-
culation mode. This can be used
when outside conditions such as
smoke, odors, dust, or high humid-
ity are present. Activating recircu-
lation will cause the LED in the control button to
illuminate.
NOTE:
• Continuous use of the recirculation mode
may make the inside air stuffy and win-
dow fogging may occur. Extended use of
this mode is not recommended.
• The use of the recirculation mode in cold
or damp weather could cause windows to
fog on the inside, because of moisture
buildup inside the vehicle. Select the Out-
side Air position for maximum defogging.
• The A/C will engage automatically to pre-
vent fogging when the recirculation but-
187