WARNING!(Continued)
• Being too close to the Supplemental Side
Airbag Inflatable Curtain (SABIC) and/or
Seat-Mounted Side Airbag (SAB) during
deployment could cause you to be severely
injured or killed.
Airbag Deployment Sensors and
Controls
Occupant Restraint Controller (ORC)
The ORC is part of a regulated safety system
required for this vehicle.
The ORC determines if deployment of the front
and/or side airbags in a frontal or side collision
is required. Based on the impact sensors sig-
nals, a central electronic ORC deploys the
Advanced Front Airbags, Supplemental Driver
Side Knee Airbag, Supplemental Side Airbag
Inflatable Curtain (SABIC), Supplemental Seat-
Mounted Side Airbags (SAB), and front seat
belt pretensioners, as required, depending on
the severity and type of impact. Advanced Front Airbags and knee airbag are
designed to provide additional protection by
supplementing the seat belts in certain frontal
collisions depending on the severity and type
of collision. Advanced Front Airbags are not
expected to reduce the risk of injury in rear, or
side collisions.
The Advanced Front Airbags and knee airbag
will not deploy in all frontal collisions, including
some that may produce substantial vehicle
damage — for example, some pole collisions,
truck underrides, and angle offset collisions.
On the other hand, depending on the type and
location of impact, Advanced Front Airbags
may deploy in crashes with little vehicle front-
end damage but that produce a severe initial
deceleration.
The side airbags will not deploy in all side
collisions. Side airbag deployment will depend
on the severity and type of collision.
Because airbag sensors measure vehicle de-
celeration over time, vehicle speed and dam-
age by themselves are not good indicators of
whether or not an airbag should have de-
ployed.Seat belts are necessary for your protection in
all accidents, and also are needed to help keep
you in position, away from an inflating airbag.
The ORC monitors the readiness of the elec-
tronic parts of the airbag system whenever the
ignition switch is in the START or ON/RUN
position. If the key is in the LOCK position, in
the ACC position, or not in the ignition, the
airbag system is not on and the airbags will not
inflate.
The ORC contains a backup power supply
system that may deploy the airbags even if the
battery loses power or it becomes discon-
nected prior to deployment.
Also, the ORC turns on the Airbag
Warning Light in the instrument
panel for approximately four to
eight seconds for a self-check
when the ignition is first turned to
the ON/RUN position. After the
self-check, the Airbag Warning Light will turn
off. If the ORC detects a malfunction in any part
of the system, it turns on the Airbag Warning
Light, either momentarily or continuously. A
41
single chime will sound if the light comes on
again after initial startup.
It also includes diagnostics that will illuminate
the instrument cluster Airbag Warning Light if a
malfunction is noted that could affect the airbag
system. The diagnostics also record the nature
of the malfunction.
WARNING!
Ignoring the Airbag Warning Light in your
instrument panel could mean you won’t have
the airbags to protect you in a collision. If the
light does not come on, stays on after you
start the vehicle, or if it comes on as you drive,
have an authorized dealer service the airbag
system immediately.
Driver and Passenger Advanced Front
Airbag Inflator Units
The Driver and Passenger Advanced Front
Airbag Inflator Units are located in the center of
the steering wheel and the right side of the
instrument panel. When the ORC detects a
collision requiring the Advanced Front Airbags,
it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the Ad-
vanced Front Airbags. Different airbag inflation
rates are possible, based on the collision type
and severity. The steering wheel hub trim cover
and the upper right side of the instrument panel
separate and fold out of the way as the airbags
inflate to their full size. The airbags fully inflate
in about 50 to 70 milliseconds. This is about half
of the time it takes to blink your eyes. The
airbags then quickly deflate while helping to
restrain the driver and front passenger.
The Advanced Front Airbag gas is vented
through the vent holes in the sides of the
airbag. In this way, the airbags do not interfere
with your control of the vehicle.
Supplemental Driver Side Knee Airbag
Inflator Unit
The driver side knee airbag unit is located in
the instrument panel trim beneath the steering
column. When the ORC detects a collision
requiring the airbag, it signals the inflator units.
A large quantity of non-toxic gas is generated
to inflate the knee airbag. The trim cover sepa-
rates and folds out of the way allowing the
airbag to inflate to the full size. The airbag fully
inflates in about 15 to 20 milliseconds.Supplemental Seat-Mounted Side Airbag
(SAB) Inflator Units
The Supplemental Seat-Mounted Side Airbags
are designed to activate only in certain side
collisions.
The ORC determines if a side collision requires
the side airbags to inflate based on the severity
and type of collision.
Based on the severity and type of collision, the
side airbag inflator on the crash side of the
vehicle may be triggered, releasing a quantity
of non-toxic gas. The inflating side airbag exits
through the seat seam into the space between
the occupant and the door. The side airbags
fully inflate in about 10 milliseconds. The side
airbag moves at a very high speed and with
such a high force, that it could injure you if you
are not seated properly, or if items are posi-
tioned in the area where the side airbag in-
flates. This especially applies to children.
Supplemental Side Airbag Inflatable
Curtain (SABIC) Inflator Units
During collisions where the impact is confined
to a particular area of the side of the vehicle,
the ORC may deploy the SABIC airbags, de-
42
pending on the severity and type of collision. In
these events, the ORC will deploy the SABIC
only on the impact side of the vehicle.
A quantity of non-toxic gas is generated to
inflate the side curtain airbag. The inflating side
curtain airbag pushes the outside edge of the
headliner out of the way and covers the win-
dow. The airbag inflates in about 30 ms (about
one-quarter of the time that it takes to blink your
eyes) with enough force to injure you if you are
not belted and seated properly, or if items are
positioned in the area where the side curtain
airbag inflates. This especially applies to chil-
dren. The side curtain airbag is only about
3-1/2 in (9 cm) thick when it is inflated.
Because airbag sensors estimate deceleration
over time, vehicle speed and damage are not
good indicators of whether or not an airbag
should have deployed.
NOTE:
In a rollover the pretensioners, and/or SAB
and SABIC airbags may deploy on both
sides of the vehicle.Front and Side Impact Sensors
In front and side impacts, impact sensors can
aid the ORC in determining appropriate re-
sponse to impact events. Additional sensors in
the ORC determine the level of airbag deploy-
ment and provide verification.
Enhanced Accident Response System
In the event of an impact causing airbag de-
ployment, if the communication network re-
mains intact, and the power remains intact,
depending on the nature of the event the ORC
will determine whether to have the Enhanced
Accident Response System perform the follow-
ing functions:
•
Cut off fuel to the engine.
• Flash hazard lights as long as the battery
has power or until the ignition key is turned
off.
• Turn on the interior lights, which remain on as
long as the battery has power or until the
ignition key is removed.
• Unlock the doors automatically. If a Deployment Occurs
The Advanced Front Airbags are designed to
deflate immediately after deployment.
NOTE:
Front and/or side airbags will not deploy in
all collisions. This does not mean some-
thing is wrong with the airbag system.
If you do have a collision which deploys the
airbags, any or all of the following may occur:
•
The nylon airbag material may sometimes
cause abrasions and/or skin reddening to
the driver and front passenger as the air-
bags deploy and unfold. The abrasions are
similar to friction rope burns or those you
might get sliding along a carpet or gymna-
sium floor. They are not caused by contact
with chemicals. They are not permanent and
normally heal quickly. However, if you
haven’t healed significantly within a few
days, or if you have any blistering, see your
doctor immediately.
43
•As the airbags deflate, you may see some
smoke-like particles. The particles are a nor-
mal by-product of the process that gener-
ates the non-toxic gas used for airbag infla-
tion. These airborne particles may irritate the
skin, eyes, nose, or throat. If you have skin or
eye irritation, rinse the area with cool water.
For nose or throat irritation, move to fresh air.
If the irritation continues, see your doctor. If
these particles settle on your clothing, follow
the garment manufacturer’s instructions for
cleaning.
Do not drive your vehicle after the airbags have
deployed. If you are involved in another colli-
sion, the airbags will not be in place to protect
you.
WARNING!
Deployed airbags and seat belt pretensioners
cannot protect you in another collision. Have
the airbags, seat belt pretensioners, and the
front seat belt retractor assemblies replaced
by an authorized dealer as soon as possible.
Also, have the Occupant Restraint Controller
(ORC) system serviced as well. Maintaining Your Airbag System
WARNING!
•
Modifications to any part of the airbag
system could cause it to fail when you need
it. You could be injured if the airbag system
is not there to protect you. Do not modify
the components or wiring, including adding
any kind of badges or stickers to the steer-
ing wheel hub trim cover or the upper right
side of the instrument panel. Do not modify
the front bumper, vehicle body structure, or
add aftermarket side steps or running
boards.
• It is dangerous to try to repair any part of
the airbag system yourself. Be sure to tell
anyone who works on your vehicle that it
has an airbag system.
(Continued)
WARNING!(Continued)
• Do not attempt to modify any part of your
advanced airbag system. The airbag may
inflate accidentally or may not function
properly if modifications are made. Take
your vehicle to an authorized dealer for any
advanced airbag system service. If your
seat, including your trim cover and cushion,
needs to be serviced in any way (including
removal or loosening/tightening of seat at-
tachment bolts), take the vehicle to your
authorized dealer. Only manufacturer ap-
proved seat accessories may be used. If it
is necessary to modify the airbag system
for persons with disabilities, contact your
authorized dealer.
44
Airbag Warning LightYou will want to have the airbags
ready to inflate for your protection
in a collision. The airbag system is
designed to be maintenance free,
if any of the following occurs, have
an authorized dealer service the
airbag system immediately.
• The Airbag Warning Light does not come on
during the four to eight seconds when the
ignition switch is first turned to the ON/RUN
position.
• The Airbag Warning Light remains on after
the four to eight-second interval.
• The Airbag Warning Light comes on intermit-
tently or remains on while driving. NOTE:
If the speedometer, tachometer, or any en-
gine related gauges are not working, the
Occupant Restraint Controller (ORC) may
also be disabled. The airbags may not be
ready to inflate for your protection. Promptly
check the fuse block for blown fuses. Refer
to the label located on the inside of the fuse
block cover for the proper airbag fuses. See
your authorized dealer if the fuse is good.
Event Data Recorder (EDR)This vehicle is equipped with an event data
recorder (EDR). The main purpose of an EDR is
to record, in certain crash or near crash-like
situations, such as an air bag deployment or
hitting a road obstacle, data that will assist in
understanding how a vehicle’s systems per- formed. The EDR is designed to record data
related to vehicle dynamics and safety systems
for a short period of time, typically 30 seconds
or less. The EDR in this vehicle is designed to
record such data as:
•
How various systems in your vehicle were
operating;
• Whether or not the driver and passenger
safety belts were buckled/fastened;
• How far (if at all) the driver was depressing
the accelerator and/or brake pedal; and,
• How fast the vehicle was traveling.
These data can help provide a better under-
standing of the circumstances in which crashes
and injuries occur.
45
IL = Suitable for particular ISOFIX child restraint
systems (CRS) given in the attachment list.
These ISOFIX CRS are those of the “specific
vehicle”, “restricted” or “semi-universal” cat-
egories.
X = ISOFIX position not suitable for ISOFIX
child restraint systems in this mass group
and/or this size class.
Children 12 years and under should ride prop-
erly buckled up in a rear seat, if available.
According to crash statistics, children are safer
when properly restrained in the rear seats
rather than in the front.
There are different sizes and types of restraints
for children from newborn size to the child
almost large enough for an adult safety belt.
Always check the child seat Owner’s Manual to
ensure you have the right seat for your child.
Use the restraint that is correct for your child.WARNING!
In an collision, an unrestrained child, even a
tiny baby, can become a projectile inside the
vehicle. The force required to hold even an
infant on your lap can become so great that
you could not hold the child, no matter how
strong you are. The child and others could be
badly injured. Any child riding in your vehicle
should be in a proper restraint for the child’s
size.
Infants and Child Restraints
• Safety experts recommend that children ride
rearward-facing in the vehicle until they are
at least one year old and weigh at least
20 lbs (9 kg). Two types of child restraints
can be used rearward-facing: infant carriers
and convertible child seats.
• The infant carrier is only used rearward-
facing in the vehicle. It is recommended for
children who weigh up to about 20 lbs (9 kg).
Convertible child seats often have a higher
weight limit in the rearward-facing direction
than infant carriers do, so they can be used rearward-facing by children who weigh more
than 20 lbs (9 kg) but are less than one year
old. Both types of child restraints are held in
the vehicle by the lap/shoulder belt or the
ISOFIX child restraint anchorage system
(Refer to “ISOFIX — Child Seat Anchorage
System”)
When using certain Child Restraint Systems
with rigid attachments ISOFIX and foot stands
extending to the vehicle floor, remove the ve-
hicle floor mat prior to installation to ensure a
secure fit. Refer to the Child Restraint Owner’s
Manual for additional information.
WARNING!
• Rearward-facing child seats must never be
used in the front seat of a vehicle with the
front passenger airbag unless the airbag is
turned off. An airbag deployment could
cause severe injury or death to infants in
this position.
(Continued)
48
WARNING!(Continued)
• Improper installation can lead to failure of
an infant or child restraint. It could come
loose in a collision. The child could be
badly injured or killed. Follow the manufac-
turer’s directions exactly when installing an
infant or child restraint.
• A rearward-facing infant restraint should
only be used in a rear seat. A rearward-
facing infant restraint in the front seat may
be struck by a deploying passenger airbag
which may cause severe or fatal injury to
the infant.
Here are some tips for getting the most out of
your child restraint:
• Before buying any restraint system, make
sure that it has a label certifying that it meets
all applicable Safety Standards. Chrysler
Group LLC also recommends that you try a
child restraint in the vehicle seats where you
will use it before you buy it. •
The restraint must be appropriate for your
child’s weight and height. Check the label on
the restraint for weight and height limits.
• Carefully follow the instructions that come
with the restraint. If you install the restraint
improperly, it may not work when you need it.
• Except for the second row center seating
position, all passenger seat belts are
equipped with cinching latch plates. The
second row center position has an automatic
locking retractor. Both types of seat belts are
designed to keep the lap portion tight
around the child restraint so that it is not
necessary to use a locking clip. If the seat
belt has a cinching latch plate, pulling up on
the shoulder portion of the lap/shoulder belt
will tighten the belt (the cinching latch plate
will keep the belt tight; however, any seat belt
system will loosen with time, so check the
belt occasionally and pull it tight if neces-
sary). For the second row center seat belt
with the automatic locking retractor, pull the
belt from the retractor until there is enough
allowance to pass it through the child re-
straint and slide the latch plate into the
buckle. Then, pull the belt until it is fully extended from the retractor. Allow the belt to
return into the retractor, pulling on the excess
webbing to tighten the lap portion around the
child restraint. For additional information, re-
fer to
Automatic Locking Mode .
• In the rear seat, you may have trouble tight-
ening the lap/shoulder belt on the child re-
straint because the buckle or latch plate is
too close to the belt path opening on the
restraint. Disconnect the latch plate from the
buckle and twist the short buckle-end belt
several times to shorten it. Insert the latch
plate into the buckle with the release button
facing out.
• If the belt still cannot be tightened, or if
pulling and pushing on the restraint loosens
the belt, disconnect the latch plate from the
buckle, turn the buckle around, and insert
the latch plate into the buckle again. If you
still cannot make the child restraint secure,
try a different seating position.
• Buckle the child into the restraint exactly as
the manufacturer’s instructions tell you.
• When your child restraint is not in use, se-
cure it in the vehicle with the seat belt or
49
WARNING!
•An incorrectly anchored tether strap could
lead to increased head motion and possible
injury to the child. Use only the anchor
positions directly behind the child seat to
secure a child restraint top tether strap.
• Do not use the cargo tie downs located on
the load floor. Improper usage of the tether
can lead to a failure of an infant or child
restraint. The child could be badly injured
or killed. Transporting Pets
Airbags deploying in the front seat could harm
your pet. An unrestrained pet will be thrown
about and possibly injured, or injure a passen-
ger during panic braking or in an accident. Pets
should be restrained in the rear seat in pet
harnesses or pet carriers that are secured by
seat belts.
ENGINE BREAK-IN
RECOMMENDATIONS
A long break-in period is not required for the
engine and drivetrain (transmission and axle) in
your vehicle.
Drive moderately during the first 300 miles
(500 km). After the initial 60 miles (100 km),
speeds up to 50 or 55 mph (80 or 90 km/h) are
desirable.
While cruising, brief full-throttle acceleration
within the limits of local traffic laws, contributes
to a good break-in. Wide-open throttle accel-
eration in low gear can be detrimental and
should be avoided.
The engine oil installed in the engine at the
factory is a high-quality energy conserving type
lubricant. Oil changes should be consistent
with anticipated climate conditions under
which vehicle operations will occur. For the
recommended viscosity and quality grades re-
fer to “Maintenance Procedures” in “Maintain-
ing Your Vehicle”. NON-DETERGENT OR
STRAIGHT MINERAL OILS MUST NEVER BE
USED.
A new engine may consume some oil during its
first few thousand miles (kilometers) of opera-
tion. This should be considered a normal part
of the break-in and not interpreted as an indi-
cation of difficulty.
Additional Requirements For Diesel
Engine — If Equipped
During the first 1500 km avoid heavy loads, e.g.
driving at full throttle. Do not exceed 2/3 of the
maximum permissible engine speed for each
gear. Change gear in good time. Do not shift
down a gear manually in order to brake.
Top Tether Strap Mounting
54