2010 INFINITI QX56 ignition

DEF-36
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
B2191: DIFFERENCE OF KEY———SEC-34
B2192: ID DISCORD BCM-ECM ———SEC-35
B2193: CHAIN OF BCM-ECM ———SEC-37
B2552: INTELLIGENT KEY ———SEC-39
B2590: NATS MALFUNCTION ———SEC-40
C1708: [NO DATA] FL ———WT-14
C1709: [NO DATA] FR ———WT-14
C1710: [NO DATA] RR ———WT-14
C1711: [NO DATA] RL ———WT-14
C1712: [CHECKSUM ERR] FL ———WT-16
C1713: [CHECKSUM ERR] FR ———WT-16
C1714: [CHECKSUM ERR] RR ———WT-16
C1715: [CHECKSUM ERR] RL ———WT-16
C1716: [PRESSDATA ERR] FL ———WT-18
C1717: [PRESSDATA ERR] FR ———WT-18
C1718: [PRESSDATA ERR] RR ———WT-18
C1719: [PRESSDATA ERR] RL ———WT-18
C1720: [CODE ERR] FL ———WT-16
C1721: [CODE ERR] FR ———WT-16
C1722: [CODE ERR] RR ———WT-16
C1723: [CODE ERR] RL ———WT-16
C1724: [BATT VOLT LOW] FL ———WT-16
C1725: [BATT VOLT LOW] FR ———WT-16
C1726: [BATT VOLT LOW] RR ———WT-16
C1727: [BATT VOLT LOW] RL ———WT-16
C1729: VHCL SPEED SIG ERR ———WT-19
C1735: IGNITION SIGNAL ———WT-20
CONSULT display Fail-safeIntelligent Key
warning lamp ON Tire pressure
monitor warning
lamp ON Reference page
Revision: April 20092010 QX56

PRECAUTIONSDEF-43
< PRECAUTION >
C
DE
F
G H
I
J
K
M A
B
DEF
N
O P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005367609
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and w hether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Un it or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or el ectric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000005367612
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecti ng both battery cables with the ignition knob in the
″ LOCK ″ position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS , an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables. NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC ″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
Revision: April 20092010 QX56

DEF-44
< PRECAUTION >
PRECAUTIONS
5. When the repair work is completed, return the ignition switch to the ″LOCK ″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of a ll control units using CONSULT-III.
Handling for Adhesive and PrimerINFOID:0000000005146856
• Do not use an adhesive which is past its usable date. Shel f life of this product is limited to six months after
the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Open the seal of the primer and adhesive just before application. Discard the remainder.
• Before application, be sure to shake the primer container to stir the contents. If any floating material is found, do not use it.
• If any primer or adhesive contacts the skin, wipe it off with gasoline or equivalent and wash the skin with
soap.
• When using primer and adhesive, always observe the precautions in the instruction manual.
Revision: April 20092010 QX56

DLK-3
C
DE
F
G H
I
J
L
M A
B
DLK
N
O P
REAR LH ...............................................................
....
88
REAR LH : Description ............................................88
REAR LH : Component Function Check ...............88
REAR LH : Diagnosis Procedure ............................88
REAR RH ............................................................... ....89
REAR RH : Description ...........................................90
REAR RH : Component Function Check ...............90
REAR RH : Diagnosis Procedure ............................90
BACK DOOR ......................................................... ....91
BACK DOOR : Description ......................................91
GLASS HATCH LOCK ACTUATOR ..................92
Diagnosis Procedure ...............................................92
PASSENGER SELECT UNLOCK RELAY .........93
Description .......................................................... ....93
Component Function Check ....................................93
Diagnosis Procedure ...............................................93
INTELLIGENT KEY WARNING BUZZER ..........95
Description .......................................................... ....95
Component Function Check ..................................95
Diagnosis Procedure ...............................................95
Component Inspection ............................................96
OUTSIDE KEY ANTENNA .................................97
Description .......................................................... ....97
Component Function Check ..................................97
Diagnosis Procedure ...............................................97
STEERING LOCK UNIT .....................................99
Diagnosis Procedure ........................................... ....99
A/T SHIFT SELECTOR (PARK POSITION
SWITCH) ...........................................................
101
Diagnosis Procedure ........................................... ..101
REMOTE KEYLESS ENTRY RECEIVER ........103
Description .......................................................... ..103
Component Function Check ................................103
Diagnosis Procedure .............................................103
INTELLIGENT KEY BATTERY AND FUNC-
TION .................................................................
106
Description .......................................................... ..106
Component Function Check ................................106
Diagnosis Procedure .............................................106
HORN FUNCTION ............................................108
Description .......................................................... ..108
Component Function Check ................................108
Diagnosis Procedure ............................................108
COMBINATION METER DISPLAY FUNC-
TION .................................................................
110
Description .......................................................... ..110
Component Function Check ................................110
Diagnosis Procedure .............................................110
WARNING CHIME FUNCTION ........................111
Description ........................................................... ..111
Component Function Check ................................111
Diagnosis Procedure .............................................111
HAZARD FUNCTION ......................................112
Description .............................................................112
Component Function Check ................................112
Diagnosis Procedure .............................................112
KEY SWITCH (INTELLIGENT KEY UNIT IN-
PUT) ................................................................
113
Diagnosis Procedure .............................................113
KEY SWITCH (BCM INPUT) ...........................115
Diagnosis Procedure .............................................115
IGNITION KNOB SWITCH ..............................116
Diagnosis Procedure .............................................116
HEADLAMP FUNCTION .................................118
Diagnosis Procedure .............................................118
MAP LAMP AND IGNITION KEYHOLE ILLU-
MINATION FUNCTION ...................................
119
Diagnosis Procedure .............................................119
KEYFOB ID SET UP WITH CONSULT-III ......120
ID Code Entry Procedure ......................................120
KEYFOB ID SET UP WITHOUT CONSULT-III .121
ID Code Entry Procedure .................................... ..121
AUTOMATIC BACK DOOR SELF-DIAGNO-
SIS PROCEDURE ...........................................
123
Self-Diagnosis Procedure ......................................123
POWER LIFTGATE SWITCH FUNCTION ......125
Diagnosis Procedure ........................................... ..125
GLASS HATCH SWITCH ................................127
Diagnosis Procedure .............................................127
GLASS HATCH AJAR SWITCH .....................129
Diagnosis Procedure .............................................129
BACK DOOR CLOSE (CLOSE) SWITCH
SYSTEM ..........................................................
131
Diagnosis Procedure ........................................... ..131
BACK DOOR CLOSE (CANCEL) SWITCH
SYSTEM ..........................................................
133
Diagnosis Procedure ........................................... ..133
PINCH STRIP SYSTEM ..................................135
Diagnosis Procedure .............................................135
BACK DOOR WARNING CHIME SYSTEM ....136
Diagnosis Procedure .............................................136
HALF-LATCH SWITCH SYSTEM ...................137
Diagnosis Procedure .............................................137
BACK DOOR OPEN SWITCH SYSTEM ........138
Revision: April 20092010 QX56

DLK-10
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
AUTOMATIC DOOR LOCKS
FUNCTION DIAGNOSIS
AUTOMATIC DOOR LOCKS
System DiagramINFOID:0000000005146867
System DescriptionINFOID:0000000005146868
DOOR LOCK FUNCTION
• The door lock and unlock switch (driver side) is built into power window main switch.
• The door lock and unlock switch (passenger side) is on door trim.
• Interlocked with the locking operation of door lock and
unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors are
unlocked.
Door Key Cylinder
• With the door key inserted in the door key cylinder on driver side, turning it to “LOCK”, will lock door lock
actuator of all doors.
• With the door key inserted in the door key cylinder on driver side, turning it to “UNLOCK” onc\
e unlocks the driver side door lock actuator; turning it to “UNLOCK” again within 5 seconds after the first unlock operation
unlocks all of the other doors. - (SELECTIVE UNLOCK OPERATION)
Selective unlock operation mode can be changed usi ng “DOOR LOCK-UNLOCK SET” mode in “WORK SUP-
PORT”. Refer to DLK-53, "
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)".
AUTOMATIC DOOR LOCKS (LOCK OPERATION)
The interlock door lock function is the function that locks all doors linked with the vehicle speed.
Vehicle Speed Sensing Auto Door Lock*1
All doors are locked when the vehicle speed reaches 24 km/h (15 MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 15 MPH (24 km/h) or more.
ALKIA1482GB
Input SingleFunction Actuator
Door lock/unlock switch Door lock/unlock signal Door lock function
Each door lock actuator
Door key cylinder switch
Each door switch
Door open/close signal
Key reminder function
Combination meter Warning buzzer signal
Vehicle speed signal
Automatic door lock/unlock
function
TCM Shift position signal
Revision: April 20092010 QX56

AUTOMATIC DOOR LOCKSDLK-11
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
If a door is opened and closed at any time during one ignition cycle (O\
FF → ON), even after initial auto door
lock has taken place, the BCM will relock all doors when the vehicle speed reaches 15 MPH (24 km/h) or more
again.
Setting change of Automatic Door Locks (LOCK) Function
The lock operation setting of the aut omatic door locks function can be changed.
With CONSULT-III
The ON/OFF switching of the automatic door locks (LOCK) function and the type selection of the automatic
door locks (LOCK) function can be performed at the WO RK SUPPORT setting of CONSULT-III. Refer to DLK-
53, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)".
Without CONSULT- III
The automatic door locks (LOCK) function can be swit ched ON/OFF by performing the following operation.
1. Close all doors (door switch OFF).
2. Turn ignition switch ON.
3. Within 20 seconds of turning the ignition switch ON, press and hold the door lock and unlock switch to the LOCK position for more than 5 seconds.
4. The switching is completed when the hazard lamps blink.
5. The ignition switch must be turned OFF and ON again between each setting change.
AUTOMATIC DOOR LOCKS (UNLOCK OPERATION)
The automatic door locks (UNLOCK) function is the function that unlocks all doors linked with the key position.
IGN OFF Interlock Door Unlock*1
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuator s when it detects that the power supply position is
changed from ignition switch ON to OFF.
Setting change of Automatic Door Locks (UNLOCK) Function
The lock operation setting of the aut omatic door locks function can be changed.
With CONSULT-III
The ON/OFF switching of the automatic door locks (UNL OCK) function and the type selection of the automatic
door locks (UNLOCK) function can be performed at the WORK SUPPORT setting of CONSULT-III. Refer to
DLK-53, "
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)".
Without CONSULT- III
The automatic door locks (UNLOCK) function can be sw itched ON/OFF by performing the following operation.
1. Close all doors (door switch OFF).
2. Turn ignition switch ON.
3. Within 20 seconds of turning the ignition switch ON, press and hold the door lock and unlock switch to the UNLOCK position for more than 5 seconds.
4. The switching is completed when the hazard lamps blink.
5. The ignition switch must be turned OFF and ON again between each setting change.
*1: This function is set to ON before delivery.
OFF → ON : 2 blinks
ON → OFF : 1 blink
OFF → ON : 2 blinks
ON → OFF : 1 blink
Revision: April 20092010 QX56

DLK-12
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
AUTOMATIC DOOR LOCKS
Component Parts Location
INFOID:0000000005146869
Component DescriptionINFOID:0000000005146870
ALKIA1835ZZ
1. Key switch and ignition knob switch M12 2. BCM M18, M19, M20 3. Combination meter M24
4. TCM F9 5. Front door lock assembly LH (key cyl-
inder switch) D14
Front door lock assembly RH D114 6. Main power window and door lock/
unlock switch D7, D8
7. Front door switch LH B8 RH B108 8. Rear door switch LH B18
RH B116 9. Back door latch (door ajar switch)
D503
10. Rear door lock actuator LH D205 RH D305 11. Glass hatch lock actuator D711 12. Back door and glass hatch switch
assembly (glass hatch switch) D706
Item Function
BCM Controls the door lock function and room lamp function.
Door lock and unlock switch Input lock or unlock signal to BCM.
Revision: April 20092010 QX56

DOOR LOCK FUNCTIONDLK-15
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR LOCK AND UNLOCK SWITCH : Component Parts LocationINFOID:0000000005146873
DOOR LOCK AND UNLOCK SWITCH : Component DescriptionINFOID:0000000005146874
1. Key switch and ignition knob switch M12 2. BCM M18, M19, M20 (view with instrument panel removed)3. Front door lock assembly LH (key
cylinder switch) D14
Front door lock actuator RH D114
4. Main power window and door lock/un- lock switch D7, D8 5. Front door switch
LH B8
RH B108 6. Rear door switch
LH B18
RH B116
7. Power window and door lock/unlock switch RH D105 8. Back door latch (door ajar switch)
D503 9. Rear door lock actuator
LH D205
RH D305
10. Passenger select unlock relay M7 (view with instrument panel LH removed) 11. Glass hatch lock actuator D711 12. Back door and glass hatch switch
assembly (glass hatch switch) D706
ALKIA1836ZZ
Item Function
BCM Controls the door lock function and room lamp function.
Door lock and unlock switch Transmits lock or unlock signal to BCM.
Door lock actuator Receives lock/unlock signal from BCM and locks/unlocks each door.
Revision: April 20092010 QX56