2010 INFINITI M warning

cReplacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
CAUTION
cThe TPMS is not a substitute for the regular
tire pressure check. Be sure to check the tire
pressure regularly.
c If the vehicle is being driven at speeds of less
than 16 MPH (25 km/h), the TPMS may not
operate correctly.
c Be sure to correctly install the specified size
of tires to the four wheels.
Low washer fluid warning
light
This light comes on when the washer tank fluid
is at a low level. Add washer fluid as necessary.
See ªWINDOW WASHER FLUIDº in the ª8. Main-
tenance and do-it-yourselfº section.
Preview Function warning
light (orange; if so equipped)
The light comes on if there is a malfunction in
the Brake Assist (with Preview Function) sys-
tem. If the warning light comes on, park the vehicle
in a safe place. Turn the engine off, restart the
engine, resume driving and set the ICC system
again.
If it is not possible to set the system or the
indicator stays on, it may indicate that the sys-
tem is malfunctioning. Although the vehicle is
still driveable under normal conditions, have the
vehicle checked at an INFINITI retailer.
See ªPREVIEW FUNCTION (for Intelligent Cruise
Control (ICC) system equipped models)º in the
ª5. Starting and drivingº section.
Rear Active Steer warning
light (if so equipped)
If the light comes on while the engine is run-
ning, it may indicate that there is a malfunction
with the Rear Active Steer portion of the steer-
ing system. Have the system checked by an
INFINITI retailer.
For further information about the Rear Active
Steer system, see ªREAR ACTIVE STEER SYS-
TEMº in the ª5. Starting and drivingº section.
If a malfunction occurs in the system, the Rear
Active Steer function will cease but driving can
be continued.
If the light comes on while you are driving, con-
tact an INFINITI retailer for repair.
Seat belt warning
light
The light and chime remind you to fasten seat
belts. The light illuminates whenever the igni-
tion switch is pushed to the ON position, and
will remain illuminated until the driver's seat
belt is fastened. At the same time, the chime
will sound for about 6 seconds unless the
driver's seat belt is securely fastened.
The seat belt warning light for the front passen-
ger will illuminate if the seat belt is not fastened
when the front passenger's seat is occupied.
For 5 seconds after the ignition switch is in the
ON position, the system does not activate the
warning light for the front passenger.
See ªSEAT BELTSº in the ª1. Safety Ð Seats,
seat belts and supplemental restraint systemº
section for precautions on seat belt usage.
Supplemental air bag
warning light
After pushing the ignition switch to the ON
position, the supplemental air bag warning
light will illuminate. The supplemental air bag
warning light will turn off after about 7 seconds
if the supplemental front air bag and supple-
mental side air bag, curtain side-impact air bag
systems and/or pretensioner seat belt are op-
erational.
Instruments and controls2-17
wÐ
Ð
05/14/09Ðpattie
X

If any of the following conditions occur, the
front air bag, side air bag, curtain air bag and
pretensioner systems need servicing and your
vehicle must be taken to your nearest INFINITI
retailer.
cThe supplemental air bag warning light re-
mains on after approximately 7 seconds.
c The supplemental air bag warning light
flashes intermittently.
c The supplemental air bag warning light does
not come on at all.
Unless checked and repaired, the supplemental
restraint system (air bag system) and/or the
pretensioners may not function properly.
For additional information, see ªSUPPLEMENTAL
RESTRAINT SYSTEMº in the ª1. Safety Ð Seats,
seat belts and supplemental restraint systemº
section.
WARNING
If the supplemental air bag warning light is on,
it could mean that the front air bag, side air
bag, curtain air bag and/or pretensioner sys-
tems will not operate in an accident. To help
avoid injury to yourself or others, have your
vehicle checked by an INFINITI retailer as soon
as possible.
INDICATOR LIGHTS
Adaptive Front lighting
System (AFS) indicator light
When the ignition switch is pushed to the ON
position, the Adaptive Front lighting System
(AFS) indicator light will illuminate. The light
will turn off in about 1 second if the AFS is
operational.
This light also comes on when the AFS is turned
off by pushing the OFF side of the AFS switch.
If the AFS indicator light blinks, it may indicate
the AFS is not functioning properly. Have the
system checked by an INFINITI retailer.
See ªAdaptive Front lighting System (AFS)º later
in this section.
Automatic Transmission (AT)
position indicator light
When the ignition switch is pushed to the ON
position, the indicator shows the automatic
selector shift position. (See ªAUTOMATIC
TRANSMISSIONº in the ª5. Starting and drivingº
section.)
Cruise main switch indicator
light (green)
The light comes on when the cruise control
main switch is pushed. The light goes out when the main switch is pushed again. When the
cruise control main switch indicator light comes
on, the cruise control system is operational.
Cruise set switch indicator
light
The light comes on while the vehicle speed is
controlled by the cruise control system. If the
light blinks while the engine is running, it may
indicate the cruise control system is not func-
tioning properly. Have the system checked by
an INFINITI retailer.
Front passenger air bag
status light
The front passenger air bag status light ()
will be lit and the passenger front air bag will be
OFF depending on how the front passenger seat
is being used.
For front passenger air bag status light opera-
tion, see ªINFINITI ADVANCED AIR BAG SYSTEM
(front seats)º in the ª1. Safety Ð Seats, seat
belts and supplemental restraint systemº sec-
tion of this manual.
High beam indicator
light
This light comes on when the headlight high
beam is on and goes out when the low beam is
selected.
2-18Instruments and controls
wÐ
Ð
05/14/09Ðpattie
X

Intelligent Cruise Control
(ICC) system MAIN switch
indicator light (green; if so
equipped)
The light comes on when the Intelligent Cruise
Control (ICC) system MAIN switch is pushed.
The light goes out when the MAIN switch is
pushed again. While the MAIN switch indicator
light comes on, the ICC system is operational.
Lane Departure Prevention
(LDP) ON indicator light
(green; if so equipped)
The light comes on in green when the Lane
Departure Prevention (LDP) system is turned on.
The light turns off when the system is turned
off.
NOTE:
This light is common with the lane departure
warning light (orange). (See ªLane departure
warning lightº earlier in this section.)
For more details, see ªLANE DEPARTURE WARN-
ING (LDW) SYSTEM/LANE DEPARTURE PREVEN-
TION (LDP) SYSTEMº in the ª5. Starting and
drivingº section.
Malfunction Indicator Light
(MIL)
If the malfunction indicator light comes on
steady or blinks while the engine is running, it
may indicate a potential emission control mal-
function.
The malfunction indicator light may also come
on steady if the fuel-filler cap is loose or
missing, or if the vehicle runs out of fuel. Check
to make sure the fuel-filler cap is installed and
closed tightly, and that the vehicle has at least
3 US gallons (14 liters) of fuel in the fuel tank.
After a few driving trips, the
light should
turn off if no other potential emission control
system malfunction exists.
If this indicator light remains on for 20 seconds
and then blinks for 10 seconds when the engine
is not running, it indicates that the vehicle is
not ready for an emission control system
inspection/maintenance test. (See ªREADINESS
FOR INSPECTION/MAINTENANCE (I/M) TESTº in
the ª9. Technical and consumer informationº
section.)
Operation :
The malfunction indicator light will come on in
one of two ways: c
Malfunction indicator light on steady Ð An
emission control system malfunction has
been detected. Check the fuel-filler cap. If
the fuel-filler cap is loose or missing, tighten
or install the cap and continue to drive the
vehicle. The
light should turn off after
a few driving trips. If the
light does
not turn off after a few driving trips, have the
vehicle inspected by an INFINITI retailer. You
do not need to have your vehicle towed to
the retailer.
c Malfunction indicator light blinking Ð An
engine misfire has been detected which may
damage the emission control system.
To reduce or avoid emission control system
damage:
a) Do not drive at speeds above 45 MPH (72 km/h).
b) Avoid hard acceleration or deceleration.
c) Avoid steep uphill grades.
d) If possible, reduce the amount of cargo being hauled or towed.
The malfunction indicator light may stop
blinking and remain on.
Have the vehicle inspected by an INFINITI
retailer. You do not need to have your vehicle
towed to the retailer.
Instruments and controls2-19
wÐ
Ð
05/19/09Ðtbrooks
X

CAUTION
Continued vehicle operation without having
the emission control system checked and re-
paired as necessary could lead to poor drive-
ability, reduced fuel economy, and possible
damage to the emission control system.
Slip indicator light
This light will blink when the Vehicle Dynamic
Control (VDC) system is operating, thus alerting
the driver to the fact that the road surface is
slippery and the vehicle is nearing its traction
limits.
Small light indicator
light
The light comes on when the front park, side
marker, tail and license plate lights are on.
Turn signal/hazard indicator
lights
The light flashes when the turn signal switch
lever or hazard switch is turned on.
Vehicle Dynamic Control
(VDC) off indicator light
The light comes on when the Vehicle Dynamic
Control (VDC) off switch is pushed to OFF. This
indicates that the VDC system is not operating.
When the VDC off indicator light and slip indi-
cator light come on with the VDC system turned
on, this light alerts the driver to the fact that the
VDC system's fail-safe mode is operating, for
example the VDC system may not be function-
ing properly. Have the system checked by an
INFINITI retailer. If a malfunction occurs in the
system, the VDC system function will be can-
celed but the vehicle is still driveable. For
additional information, see ªVEHICLE DYNAMIC
CONTROL (VDC) SYSTEMº in the ª5. Starting and
drivingº section of this manual.
AUDIBLE REMINDERS
Key reminder chime
A chime will sound if the driver side door is
opened while the ignition switch is pushed to
the ACC or LOCK position with the Intelligent
Key left in the Intelligent Key port. Make sure
the ignition switch is pushed to the LOCK
position, and take the Intelligent Key with you
when leaving the vehicle.
Light reminder chime
A chime will sound when the driver side door is
opened with the light switch in the
or
position, and the ignition switch is
pushed to the ACC position.
Turn the light switch off when you leave the
vehicle.
Parking brake reminder chime
The chime will sound if the vehicle is driven at
more than 4 MPH (7 km/h) with the parking
brake applied. Stop the vehicle and release the
parking brake.
Seat belt warning chime
The chime will sound for about 6 seconds
unless the driver's seat belt is securely fas-
tened.
Brake pad wear warning
The disc brake pads have audible wear warn-
ings. When a brake pad requires replacement, it
will make a high pitched scraping sound when
the vehicle is in motion. This scraping sound
will first occur only when the brake pedal is
depressed. After more wear of the brake pad,
the sound will always be heard even if the brake
2-20Instruments and controls
wÐ
Ð
05/14/09Ðpattie
X

pedal is not depressed. Have the brakes
checked as soon as possible if the warning
sound is heard.
Lane departure warning chime (if so
equipped)
When the Lane Departure Warning (LDW) or
Lane Departure Prevention (LDP) system is on,
the chime sounds if the vehicle is traveling
close to either the left or the right of a traveling
lane with detectable lane markers.
See ªLANE DEPARTURE WARNING (LDW)
SYSTEM/LANE DEPARTURE PREVENTION (LDP)
SYSTEMº in the ª5. Starting and drivingº sec-
tion for more details.The dot matrix liquid crystal display
s1is
located under the tachometer, and it displays
the Automatic Transmission (AT) position indi-
cator, the Intelligent Cruise Control (ICC) system
(if so equipped) information and the Intelligent
Key operation information.
For detailed information about each system, see
the following sections:
c Automatic Transmission (AT)
± ªWARNING/INDICATOR LIGHTS AND AU- DIBLE REMINDERSº earlier in this section.
± ªDRIVING THE VEHICLEº in the ª5. Start- ing and drivingº section. c
Intelligent Cruise Control (ICC) system
± ªINTELLIGENT CRUISE CONTROL (ICC) SYSTEMº in the ª5. Starting and drivingº
section.
c Intelligent Key system
± ªINTELLIGENT KEY SYSTEMº in the ª3. Pre-driving checks and adjustmentsº sec-
tion.
± ªPUSH-BUTTON IGNITION SWITCHº in the ª5. Starting and drivingº section.
SIC3611
DOT MATRIX LIQUID CRYSTAL DISPLAY
Instruments and controls2-21
wÐ
Ð
05/19/09Ðtbrooks
X

4. Intelligent Key insertion indicator
This indicator appears when the Intelligent Key
needs to be inserted into the Intelligent Key
port. (For example, the Intelligent Key battery is
discharged.)
If this indicator appears, insert the Intelligent
Key into the Intelligent Key port in the correct
direction. (See ªPUSH-BUTTON IGNITION
SWITCHº in the ª5. Starting and drivingº sec-
tion.)
5. Intelligent Key removal indicator
This indicator appears when the driver's door is
opened with the ignition switch in the LOCK
position and the Intelligent Key placed in the
Intelligent Key port. A key reminder chime also
sounds.
If this indicator appears, remove the Intelligent
Key from the Intelligent Key port and take it with
you when leaving the vehicle.
6. NO KEY warning
The warning appears when the door is closed
with the Intelligent Key left outside the vehicle
and the ignition switch in the ACC or ON
position. Make sure that the Intelligent Key is
inside the vehicle.When all the doors are closed, an outside chime
and inside warning chime will also sound.
See ªINTELLIGENT KEY SYSTEMº in the ª3. Pre-
driving checks and adjustmentsº section.
7. SHIFT ªPº warning
This warning appears when the ignition switch
is pushed to stop the engine with the selector
lever in any position except the P (Park) posi-
tion.
If this warning appears, move the selector lever
to the P (Park) position or push the ignition
switch to the ON position.
An inside warning chime will also sound.
See ªINTELLIGENT KEY SYSTEMº in the ª3. Pre-
driving checks and adjustmentsº section.
8. ªLOCKº warning
This warning appears when the selector lever is
moved to the P (Park) position with the ignition
switch in the ACC position after the SHIFT ªPº
warning appears.
To push the ignition switch to the LOCK posi-
tion, perform the following procedure:
SHIFT ªPº warning
!(Move the selector lever
to ªPº) !LOCK warning !(Push the ignition
switch !ignition switch position is turned to
ON) !LOCK warning !(Push the ignition
switch !ignition switch position is turned to
LOCK)
9. NO KEY ID indicator
This indicator appears when the ignition switch
is pushed and the Intelligent Key cannot be
recognized by the system with the ignition
switch in the LOCK position.
If this indicator appears, you cannot start the
engine. Check for the following causes and
perform remedies:
c The battery of the Intelligent Key carried with
you is discharged completely. Replace the
battery with a new one.
c The Intelligent Key carried with you is not
registered to the system. Use the registered
Intelligent Key.
c You do not have an Intelligent Key with you.
Carry an Intelligent Key with you.
Instruments and controls2-23
wÐ
Ð
05/14/09Ðpattie
X

WARNING
In freezing temperatures the washer solution
may freeze on the windshield and obscure your
vision which may lead to an accident. Warm
windshield with the defroster before you wash
the windshield.
CAUTION
cDo not operate the washer continuously for
more than 30 seconds.
c Do not operate the washer if the reservoir
tank is empty.
c Do not fill the window washer reservoir tank
with washer fluid concentrates at full
strength. Some methyl alcohol based
washer fluid concentrates may permanently
stain the grille if spilled while filling the win-
dow washer reservoir tank.
c Pre-mix washer fluid concentrates with wa-
ter to the manufacturer's recommended lev-
els before pouring the fluid into the window
washer reservoir tank. Do not use the win-
dow washer reservoir tank to mix the washer
fluid concentrate and water. The windshield wiper and washer operates
when the ignition switch is in the ON position.
Push the lever down to operate the wiper at the
following speed:
s1INT (intermittent) Ð rain-sensing auto wiper
system operation (See ªRAIN-SENSING
AUTO WIPER SYSTEMº later in this section.)
s2LO (low) Ð continuous low speed operation
s3HI (high) Ð continuous high speed operation
Push the lever up
s4to have one sweep
operation of the wiper. Pull the lever toward you
s5to operate the
washer. Then the wiper will also operate several
times.
SIC3886
WINDSHIELD WIPER AND WASHER SWITCH
Instruments and controls2-27
wÐ
Ð
05/15/09Ðpattie
X

XENON HEADLIGHTS
WARNING
HIGH VOLTAGE
cWhen xenon headlights are on, they produce
a high voltage. To prevent an electric shock,
never attempt to modify or disassemble. Al-
ways have your xenon headlights replaced
at an INFINITI retailer.
c Xenon headlights provide considerably
more light than conventional headlights. If
they are not correctly aimed, they might
temporarily blind an oncoming driver or the
driver ahead of you and cause a serious acci-
dent. If headlights are not aimed correctly,
immediately take your vehicle to an INFINITI
retailer and have the headlights adjusted
correctly.
When the xenon headlight is initially turned on,
its brightness or color varies slightly. However,
the color and brightness will soon stabilize.
c The life of xenon headlights will be shortened
by frequent on-off operation. It is generally
desirable not to turn off the headlights for
short intervals (for example, when the ve-
hicle stops at a traffic signal). Even when the daytime running lights are active (Canada
only), the xenon headlights do not turn on.
This way the life of the xenon headlights is
not reduced.
c If the xenon headlight bulb is close to burn-
ing out, the brightness will drastically de-
crease, the light will start blinking, or the
color of the light will become reddish. If one
or more of the above signs appear, contact an
INFINITI retailer.
HEADLIGHT SWITCH
Lighting
s1Turn the switch to theposition:
The front park, side marker, tail, license
plate and instrument lights will come on.
s2Turn the switch to theposition:
Headlights will come on and all the other
lights remain on.
SIC2411
HEADLIGHT AND TURN SIGNAL SWITCH
Instruments and controls2-29
wÐ
Ð
05/14/09Ðpattie
X