Engine oil and filter
1. Place a large drain pan under the drainplug.
2. Remove the oil filler cap.
3. Remove the drain plug
s1with a wrench
and completely drain the oil.
CAUTION
Be careful not to burn yourself, as the engine oil
is hot.
cWaste oil must be disposed of properly.
c Check your local regulations.
Perform steps 4 to 7 only when the engine oil
filter change is needed.
4. Loosen the oil filters2with an oil filter
wrench. Remove the oil filter by turning it
by hand.
5. Wipe the engine oil filter mounting sur- face with a clean rag.
CAUTION
Be sure to remove any old rubber gasket re-
maining on the mounting surface of the engine.
Failure to do so could lead to engine failure.
6. Coat the gasket on the new filter with clean engine oil.
7. Screw in the oil filter clockwise until a slight resistance is felt, then tighten ad-
ditionally more than 2/3 turn.
Oil filter tightening torque:11 to 15 ft-lb
(14.7 to 20.5 N´m)
8. Clean and re-install the drain plug with a new washer. Securely tighten the drain
plug with a wrench.
Drain plug tightening torque:22 to 29 ft-lb
(29 to 39 N´m)
Do not use excessive force.
9. Refill engine with recommended oil and install the oil filler cap securely.
CAUTION
The dipstick must be inserted in place to pre-
vent oil spillage from the dipstick hole while
filling the engine with oil.
See ªCAPACITIES AND RECOMMENDED
FUEL/LUBRICANTSº in the ª9. Technical and
consumer informationº section for drain and refill capacity. The drain and refill capacity
depends on the oil temperature and drain time.
Use these specifications for reference only.
Always use the dipstick to determine the proper
amount of oil in the engine.
10. Start the engine and check for leakage
around the drain plug and the oil filter.
Correct as required.
11. Turn the engine off and wait more than 15 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
After the operation
1. Install the engine undercover into positionas the following steps.
a. Pull the center of the small plastic clip out.
b. Hold the engine undercover into position.
c. Insert the clip through the undercover into the hole in the frame, then push the
center of the clip in to lock the clip in
place.
d. Install the other bolts that hold the un- dercover in place. Be careful not to strip
the bolts or over-tighten them.
2. Lower the vehicle carefully to the ground.
3. Dispose of waste oil and filter properly.
8-14Maintenance and do-it-yourself
wÐ
Ð
05/15/09Ðpattie
X
9 Technical and consumer information
Capacities and recommended fuel/lubricants........ 9-2
Fuel recommendation ........................... 9-4
Engine oil and oil filter recommendation ......... 9-6
Air conditioning system refrigerant and
lubricant recommendations ..................... 9-7
Specifications ..................................... 9-8
Engine ........................................ 9-8
Wheels and tires ............................... 9-9
Dimensions and weights ....................... 9-10
When traveling or registering your vehicle in
another country .................................. 9-10
Vehicle identification .............................. 9-11
Vehicle Identification Number (VIN) plate......... 9-11
Vehicle identification number
(chassis number) ............................... 9-11
Engine serial number .......................... 9-12
F.M.V.S.S./C.M.V.S.S. certification label .........9-12
Emission control information label ..............9-12
Tire and loading information label ..............9-13
Air conditioner specification label ...............9-13Installing front license plate
.......................9-14
Vehicle loading information ........................9-15
Terms ......................................... 9-15
Vehicle load capacity .......................... 9-16
Loading tips .................................. 9-17
Measurement of weights ....................... 9-18
Towing a trailer .................................. 9-18
Flat towing ...................................... 9-19
Automatic transmission ........................ 9-19
Uniform tire quality grading .......................9-19
Treadwear .................................... 9-19
Traction AA, A, B and C ........................ 9-20
Temperature A, B and C ....................... 9-20
Emission control system warranty .................9-20
Reporting safety defects (US only) .................9-21
Readiness for Inspection/Maintenance (I/M) test ....9-22
Event Data Recorders (EDR) .......................9-23
Owner's Manual/Service Manual order
information ...................................... 9-23
In the event of a collision ......................9-24
wÐ
Ð
05/19/09Ðtbrooks
X
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure instructed in the ª8.
Maintenance and do-it-yourselfº section to determine the proper refill capacity.
Capacity (Approximate)Recommended specifications
US measure
Imp measureLiter
Fuel 20 gal 16-5/8 gal 76 See ªFUEL RECOMMENDATIONº later in this section.
Engine oil*1
Drain and refill With oil filter change VK45DE AWD 6-1/8 qt 5-1/8 qt 5.8 ·Engine oil with API Certification Mark*2, *3
·Viscosity SAE 5W-30*2, *3
2WD 5-7/8 qt 4-7/8 qt 5.5
VQ35HR AWD/2WD 5-1/8 qt 4-3/8 qt 4.9
Without oil filter change VK45DE AWD 5-1/2 qt 4-5/8 qt 5.2
2WD 5-1/8 qt 4-3/8 qt 4.9
VQ35HR AWD/2WD 4-7/8 qt 4 qt 4.6
Cooling system With reservoir VK45DE 11 qt 9-1/8 qt 10.4 50% Genuine NISSAN Long Life Antifreeze/Coolant or equivalent
50% Demineralized or distilled water
VQ35HR 9-3/4 qt 8-1/8 qt 9.2
Reservoir 7/8 qt 3/4 qt 0.8
Automatic Transmission Fluid (ATF) ÐÐÐ Genuine NISSAN Matic S ATF*4
Differential gear oil ÐÐÐ Genuine NISSAN Differential Oil Hypoid Super GL-5, 80W-90 or API
GL-5, Viscosity SAE 80W-90*5
Transfer fluid ÐÐÐ Genuine NISSAN Matic J ATF*6
Power Steering Fluid (PSF) Refill to the proper oil level according to
the instructions in the ª8. Maintenance
and do-it-yourselfº section. Genuine NISSAN PSF or equivalent*7
Brake fluid Genuine NISSAN Super Heavy Duty Brake Fluid*8 or equivalent DOT 3
CAPACITIES AND RECOMMENDED
FUEL/LUBRICANTS
9-2Technical and consumer information
wÐ
Ð
05/15/09Ðpattie
X
Capacity (Approximate)Recommended specifications
US measure
Imp measureLiter
Multi-purpose grease NLGI No. 2 (Lithium soap base)
Air conditioning system refrigerant ÐÐÐ HFC-134a (R-134a)*9
Air conditioning system lubricants ÐÐÐ NISSAN A/C System Oil Type S or exact equivalent
Window washer fluid ÐÐÐ Genuine NISSAN Windshield Washer Concentrate Cleaner & Anti-
freeze or equivalent
*1:For additional information, see ªENGINE OILº in the ª8. Maintenance and do-it-yourselfº section for changing engine oil.
*2: For additional information, see ªENGINE OIL AND OIL FILTER RECOMMENDATIONº later in this section.
*3: INFINITI recommends Genuine NISSAN Ester Oil available at your INFINITI retailer.
*4: For 5-speed AT: If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used. Using automatic transmission fluid other than Genuine NISSAN Matic
S ATF or Matic J ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the INFINITI
new vehicle limited warranty.
For 7-speed AT: Using automatic transmission fluid other than Genuine NISSAN Matic S ATF will cause deterioration in driveability and automatic transmission durability, and may
damage the automatic transmission, which is not covered by the INFINITI new vehicle limited warranty.
*5: For hot climates, viscosity SAE 90 is suitable for ambient temperatures above 32ÉF (0ÉC).
*6:
If Genuine NISSAN Matic J ATF is not available, Genuine NISSAN Matic D ATF or Canada NISSAN Automatic Transmission Fluid or equivalent (if
available) may also be used.
*7:
DEXRONTMVI type ATF or Canada NISSAN Automatic Transmission Fluid may also be used.
*8: Available in mainland US through an INFINITI retailer.
*9: For additional information, see ªVEHICLE IDENTIFICATIONº later in this section for air conditioner specification label.
Technical and consumer information9-3
wÐ
Ð
05/15/09Ðpattie
X