2010 FIAT QUBO warning light

❒indicate that the vehicle is parked up by using the
devices required by law in the country in which
you are travelling (e.g. warning triangle, hazard
lights etc.);
❒open the tailgate, take the tool bag fig. 115 located
on the left of the boot by releasing the elastic
straps and take to the wheel to be replaced;
❒the bag contains the following tools fig. 116:
Ajack handle;
Bjack;
Cwheel wrench;
Dtow hook;
Etool bag elastic strap;
Ffuse extracting pliers;
Gscrewdriver.
The tool bag contains some spare fuses.❒Take the wrench C fig. 116 and from inside the
boot loose the spare wheel fastening bolt A fig.
117 to let it down. To reduce the effort, insert
screwdriver G fig. 116 in the seat in the wrench C;
❒use the wrench C fig. 116 to remove the wheel
from the vehicle fig. 118;
fig. 115F0T0206
fig. 116F0T0281
fig. 118F0T0419
134
KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICA
TIONS
INDEX

❒remove the cap B fig. 119 and release the strap,
when free the wheel from the toothed support
C by loosen the two screws;
❒for vehicles with alloy rims, remove the hub cap:
❒loosen the fastening bolts of the wheel to be
replaced by about one turn, using the wrench Cfig.
116;
❒for wheels with steel rims, remove the wheel cap;
❒turn the jack to open it partially fig. 120 and
then position it under the vehicle at the references
A fig. 121 near the wheel to be replaced;
❒turn the jack to open it until the groove A fig. 122
of the jack is correctly inserted in the lower profile
B on the side member:
❒warn anybody nearby that the vehicle is about to
be lifted. They must stay clear and not touch the
vehicle until it is back on the ground.
A
fig. 117F0T0292fig. 119F0T0169
135
KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICA
TIONS
INDEX

❒operate the jack and lift the vehicle until the wheel
is several centimetres off the ground. When
turning the crank, ensure that it rotates freely in
order to avoid grazing your hands against the
ground. The moving components of the jack
(screws and joints) can also cause injuries, so do
not touch them. If you become soiled with thelubricating grease, wash it off thoroughly;
❒fully loosen the fastening bolts and remove the
wheel;
❒make sure the contact surfaces between spare
wheel and hub are clean so that the fastening bolts
will not come loose;
❒fit the standard wheel by inserting the first bolt
two threads B fig. 123 into the hole closest to
the inflation valve A;
❒fit the hub cap, making sure that the symbol
(on
the cap) aligns with the inflation valve, and then
insert the other three bolts;
❒tighten the bolts using the wrench provided;
❒for vehicles with alloy rim, fit the hub cap;
❒turn the jack handle to lower the vehicle, and
remove the jack;
fig. 120F0T0124
fig. 121F0T0125fig. 122F0T0126
136
KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICA
TIONS
INDEX

❒use the wrench provided to fasten the bolts
completely in a criss-cross fashion as shown in fig.
124.When you have finished
❒Fix the toothed support on the wheel by means of
two screws (insert in the outer wheel support).
Refit the restraining metallic wire in the seat
and refit the protective cap A fig. 125;
❒check replaced wheel positioning under the floor
(the lifting system is supplied with a clutch to
limit the end of the stroke). Incorrect positioning
may jeopardise safety;
❒lift the wheel by fastening the bolt A fig. 117;
❒put jack and tools back in the specific tool bag;
❒reposition the tool bag in the boot;
❒secure the tool box to the hooks.
fig. 123F0T0282
fig. 124F0T0128fig. 125F0T0170
137
KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICA
TIONS
INDEX

FIX & GO AUTOMATIC QUICK TYRE
REPAIR KIT
The Fix&Go Automatic quick tyre repair kit is
located in a special container in the boot.
The quick tyre repair kit contains fig. 126:
❒a canister A containing liquid sealant, provided
with filling tube B and adhesive label C with the
wording "max. 80 km/h" to be affixed in a position
clearly visible to the driver (on the dashboard)
after repairing the tyre;
❒compressor D including gauge and connections in
the compartment;
❒instruction booklet (see fig. 127), to be used for
prompt and proper use of the quick repair kit
and to be then handed to the personnel charged
with handling the treated tyre;❒a pair of protective gloves located in the side
compartment of the compressor;
❒adapters for inflating different elements.
The Fix & Go container also contains some spare
fuses.
WARNING
Give the instruction booklet to the
per
sonnel charged with handling the
treated tyre.
Punctures caused by foreign bodies can be
repaired if the damage does not exceed
4 mm on the tread and on the shoulder of
the tyre.
fig. 126F0T0129fig. 127F0T0130
138
KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICA
TIONS
INDEX

WARNING
It is not possible to repair damage to the
t
yre sidewall. Do not use the quick
repair kit if the tyre was damaged by running
on a flat .
WARNING
Repair is not possible if the wheel rim is
dam
aged (groove is deformed, causing
air to escape). Do not remove foreign bodies
(screws or nails) from the tyre.
IMPORTANT INFORMATION:
The sealing fluid of the quick tyre repair kit is
effective at external temperatures of between -20°C
and +50°C.
WARNING
Do not operate the compressor for
lon
ger than 20 minutes at a time. Risk
of overheating.The quick repair kit is not
suitable for definitive repairs, so the tyres
repaired may be used only temporarily.
Dispose of the cylinder and the sealant
properly. Dispose according to the
national and local laws in force.
WARNING
The cylinder contains ethyl glycol. It
c
ontains latex, which may cause an
allergic reaction. Harmful if swallowed. Eye
irritant .There could be a reaction in the event
of inhalation or contact . Avoid contact with
the eyes, skin and clothes. In the event of
contact , rinse immediately with plenty of water.
Do not induce vomiting if swallowed. Rinse
your mouth out and drink plenty of water. Call
a doctor immediately. Keep out of the reach
of children.The product must not be used by
asthmatics. Do not breathe in the vapours
during insertion and suction. Call a doctor
immediately if allergic reactions are noted.
Store the cylinder in its special compartment ,
away from sources of heat .The sealant has
an expiry date. Replace the cylinder containing
the sealant after the expiry date.
139
KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICA
TIONS
INDEX

INFLATION PROCEDURE
WARNING
Put on the safety gloves provided
to
gether with the quick tyre repair kit .
❒Apply the handbrake. Unscrew the tyre valve cap,
take out the flexible filler pipe A fig. 128 and
tighten the ring nut B on the tyre valve;
❒make sure that switch E fig. 130 of the compressor
is at 0 (off ), start the engine, insert plug D fig. 129
in the cigar lighter socket and turn the compressor
on by setting switch E fig. 130 to I (on). Inflate
the tyre to the pressure specified in the "Cold tyre
pressures" paragraph in the "Technical
specifications" section. For a more accurate
reading, check pressure gauge F fig. 130 with the
compressor off;❒if after 5 minutes it is still impossible to reach at
least 1.5 bar, disengage compressor from valve
and unplug it from the socket, then move the car
forth for approx. ten metres in order to distribute
the sealing fluid inside the tyre evenly, then repeat
the inflation operation;
fig. 128F0T0190
fig. 129F0T0133
fig. 130F0T0131
140
KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICA
TIONS
INDEX

❒if after this operation it is still impossible after 5
minutes to reach at least 1.8 bar, do not start
driving since the tyre is excessively damaged and
the quick tyre repair kit cannot guarantee suitable
sealing, contact Fiat Dealership;
❒if you do reach the tyre pressure specified in the
“Cold tyre pressures” paragraph of the “Technical
specifications” section, continue your journey
immediately;
WARNING
Apply the adhesive label where it can be
easily
seen by the driver as a reminder
that the tyre has been treated with the quick
repair kit . Drive carefully, particularly on bends.
Do not exceed 80 km/h. Do not accelerate or
brake suddenly.
❒after having driven for about 10 minutes, stop and
recheck the tyre pressure; remember to apply the
handbrake;
WARNING
If the pressure has fallen below 1.8 bar,
do
not drive any further: the Fix&Go
automatic quick tyre repair kit cannot
guarantee proper hold because the tyre is too
damaged. Contact a Fiat Dealership.❒if, on the other hand, the pressure is at least 1.8
bar, restore the correct pressure (with the engine
running and the handbrake applied) and resume
driving;
❒drive with the utmost care to the nearest Fiat
Dealership.
WARNING
Remember to inform the workshop that
t
he tyre has been treated with a quick
repair kit . Give the instruction booklet to the
personnel charged with handling the treated
tyre.
141
KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICA
TIONS
INDEX