2010 FIAT PUNTO EVO Drl

Selecting “Set Clock”
– briefly press the MENU ESC button to select the first
value to change (hours);
– press the +and –buttons (with single presses) to se-
lect the new setting;
– briefly press the MENU ESC button to store the new
setting and go to the next setup menu option (minutes);
– after setting the values with the same procedure, go back
to the previous menu item.
Hold down the MENU ESC button:
– to quit the setup menu if you are in the menu;
– to quit to the menu if you are setting an option;
– to save only the settings already stored (and confirmed
by pressing the MENU ESC button).
The setup menu environment is timed; when quitting the
menu due to timing expiry, only the settings stored by the
user are saved (having been confirmed by briefly pressing
button MENU ESC).
CONTENTS TECHNICAL
SPECIFICATIONS SERVICING
AND CARE IN AN
EMERGENCY WARNING LIGHTS
AND MESSAGES STARTING
AND DRIVING SAFETY
KNOWING
YOUR
VEHICLE
19
Briefly press button MENU ESC to start browsing from
the standard screen. Press +or –to browse within the
menu.
NBFor safety reasons, only the short menu may be ac-
cessed while the car is moving (“SPEEd” setting). Stop the
car to access the full menu.
The menu includes the following items:
– SPEEd
– CornEr (for versions/markets where provided)
– Hour
–bUZZ
– Unit
– BAG P
– drl (for versions/markets where provided)
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 19

CONTENTS TECHNICAL
SPECIFICATIONSSERVICING
AND CAREIN AN
EMERGENCY WARNING LIGHTS
AND MESSAGESSTARTING
AND DRIVINGSAFETY
KNOWING
YOUR
VEHICLEBag P
(Passenger front and side airbag activation/
deactivation)
(for versions/markets where available)
This function is used to activate/deactivate the front pas-
senger’s air bag.
Proceed as follows:
❒press MENU ESC and, after the message BAG P OFF
(to deactivate) or BAG P On (to activate) is displayed
by pressing buttons +or –, press MENU ESC again;
❒the confirmation request message will be displayed;
❒press +or –to select YES (confirming activa-
tion/deactivation) or no (to abort);
❒briefly press MENU ESC to confirm setting and go back
to the menu screen or hold the button down to go back
to the standard screen without saving.drl
(activate/deactivate daytime running lights)
(for versions/markets where provided)
This function allows you to activate/deactivate the daytime
running lights.
Proceed as follows to switch this function on or off:
– press the MENU ESC button briefly: the display will show
a submenu;
– press the MENU ESC button briefly, the display will show
On or Off flashing depending on the previous setting;
– press +or –to change the setting;
– briefly press the MENU ESC button to go back to the
submenu screen or hold the button down to go back to
the main menu screen without saving;
– hold down MENU ESC again to go back to the standard
screen or main menu, depending on which point in the
menu you have reached.
22
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 22

190
F0U0250mfig. 167
DAYTIME RUNNING LIGHTS (DRL)
To change the bulb, proceed as follows:
❒turn the bulb holder A-fig. 167 anti-clockwise using the
tab and pull it out;
❒remove the bulb B by pushing it in slightly and turning
it anti-clockwise;
❒refit the bulb holder by putting it in its housing and turn-
ing it clockwise until it locks into place.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0150mfig. 168
MAIN/DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the rubber cap;
❒disconnect the central electric connector B-fig. 168 and
release the bulb holder catch;
❒remove the bulb A and replace it;
❒fit the new bulb, aligning the outlines of the metallic part
with the grooves on the reflector;
❒refit the bulb holder catch and reconnect the electri-
cal connector;
❒refit the cap A, ensuring that it locks into place.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 190