2010 FIAT LINEA RHD stop start

7
In this case, turn the key to STOPand
then back to MAR; try with the other
keys provided if the problem persists .
Contact a Fiat Dealership if you still
can’t start the engine.
IMPORTANT Each key has its own code
which must be stored by the system ECU.
Conta ct a Fiat Dealersh ip to have
new keys (up to eight) stored. Warning light
coming on when driving
If the warning light turns on, this
means that the system is running a self-
test (for example for a voltage drop).
If the warning light stays on, con-
tact a Fiat Dealership.
The electronic components
inside the key may be dam-
aged if the key is submitted to
sharp knocks.OPERATION
Each time the car is started turning the ig-
nition key to MAR, the Fiat CODE sys-
tem control unit sends a recognition code
to the engine control unit to deactivate
the inhibitor.
The code is sent only if the Fiat CODE
system control unit has recognised the
code transmitted from the key.
Each time the ignitio n key is turned to
STOP, the Fiat CODE system deactivates
the functions of the engine electronic con-
trol unit.
If the code has not been recognised cor-
rectly, the warning light turns on ac-
companied by the related message on the
display (see section “Warning lights and
messages”).
SAFETY
DEVICES CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS

LINEA Owner HAND BOOK RHD.pdf 7LINEA Owner HAND BOOK RHD.pdf 78/21/09 2:15:59 PM8/21/09 2:15:59 PM

IGNITION
DEVICE
The key can be turned to 3 different po-
sitions fig. 8:
STOP: engine off, key extractable,
steering locked. Some electrical devices
(e.g. sound system, central door lock-
ing system, etc.) may work.
MAR: driving position. All electrical de-
vices may work.
AV V: engine starting (unstable posi-
tion).
The ignition switch is fitted with an elec-
tronic safety system that, in the event the
engine is not started, turns back the igni-
tion key to STOPbefore repeating the
starting operation.STEERING COLUMN LOCK
Engaging
When the key is at STOP, remove the
key and turn the steering wheel until it
locks.
Disengaging
Rock the steering wheel slightly as you
turn the ignition key to MAR.
If the ignition device is tam-
pered with (e.g.: attempted
theft), have it checked over by a Fiat
Dealership as soon as possible.
WARNING
Always remove the key when
you leave your car to pre-
vent someone from accidentally op-
erating the controls . Remember to
apply the handbrake. Engage first
gear if the car is parked uphill or re-
verse if the car is parked downhill.
Never leave children unattended in
the car.
WARNING
fig. 8
Never extract the key while
the vehicl e is moving. The
steering wheel would be locked as
soon as the steering wheel is turned.
This also applies to when the car is
towed.
WARNING
It is absolutely forbidden to
carr y out whatever after-
market operation involving steering
system or steering column modifica-
tions (e.g .: installation of anti-theft
device) that could badly affect per-
formance and safety, cause the lapse
of warranty and also result in non-
compliance of the car with homolo-
gation requirements.
WARNING



F0R0009m
12
DEVICES CORRECT USE
OF THE
CAR
MESSAGES
EMERGENCY
MAINTENANCE
SPECIFICATIONS
INDEX
AND CONTROLS
SAFETY LIGHTS AND
CAR
DASHBOARD
IN AN
TECHNICAL
WARNING
LINEA Owner HAND BOOK RHD.pdf 12LINEA Owner HAND BOOK RHD.pdf 128/21/09 2:16:00 PM8/21/09 2:16:00 PM

18
Briefly press button MENU ESCto start browsing
from the standard screen. Press +or –to browse with-
in the menu.
NoteOnly the short menu may be accessed for rea-
sons of safety while the car is moving (“SPEEd” setting).
Stop the car to access the full menu.
fig. 17
F0R2003g
+ –
+
–
+
–+
– +–
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
(where provided)
LINEA Owner HAND BOOK RHD.pdf 18LINEA Owner HAND BOOK RHD.pdf 188/21/09 2:16:00 PM8/21/09 2:16:00 PM

Window demisting
In the event of considerable outside mois-
ture and/or rain and/or considerable
dif-
ferences in temperature inside and outside
the passenger compartment,
perform the
following preventive demisting procedure:
turn knob Ato the red sector;
switch internal air recirculation off;
turn knob Cto and change it back
to if demisting does not improve;
turn knob Bto 2
ndspeed.
IMPORTANT The climate control system
is very useful to prevent window misting
up in presence of high humidity since it
dries the air.HEATED REAR WINDOW DEMIS-
TING/DEFROSTING
(where provided) fig. 34
Press button Ato start this function;
when this function is on the button led is
on.
This function is timed and it will turn off
automatically after 20 minutes. Press A
again to switch it off before.
IMPORTANT Do not apply stickers on
the inside of the rear window over
the
heating filaments to avoid damage that
might cause it to stop working properly.
fig. 34F0R0035m
After demistin g/defrosting, operate the
controls to restore the required comfort.
IMPORTANT The climate control system
is very useful for faster demisting because
it dries the air. Adjust the controls as de-
scribed above and press knob Eto switch
the climate control system on: the LED on
the knob will light up.




42
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
LINEA Owner HAND BOOK RHD.pdf 42LINEA Owner HAND BOOK RHD.pdf 428/21/09 2:16:04 PM8/21/09 2:16:04 PM

USING THE CLIMATE
CONTROL SYSTEM
The system can be started in different
ways,
but it is advisable to start by press-
ing the AUTObutton and then turning
the knobs to set the temperature required
on the display.
The system will start running automatically
in this way and the set comfortable tem-
perature will be reached as quickly as pos-
sible. The system will adjust the temper-
ature, the quantity and the distribution of
the air introduced into the passenger com-
partment and will manage the recircula-
tion function and the compressor.
Manual intervention is only required for
the following functions during fully auto-
matic operation.
air recirculation, to keep the
function always either on or off;
to speed up demisting/defrosting of
windscreen, rear window and exter-
nal rearview mirrors;During completely automatic system op-
eration, you can vary the set temperature,
the air distribution and the fan speed us-
ing the corresponding buttons or knobs
at any time: the system will automatically
change settings to adapt to the new re-
quest.
During fully automatic operation (FULL
AUTO), the word FULLwill disappear
if the air distribution, air speed,
compres-
sor and/or recirculatio n settin gs are
changed. In this way, the functions will
switch from automatic to manual control
until AUTOis pressed again. With on or
more manually set functions, the intro-
duced air temperature is still managed au-
tomatically by the system, except for when
the compressor is off: in the case,
the air
introduced into the passenger compart-
ment cannot be cooler than the outside
air.Air temperature adjustment
knob (I)
Turn the knob either clockwise or anti-
clockwise to increase or lower the re-
quested temperature in the
passenger
compartment. The set temperature is
shown on the display.
Turn the knob either all to the right
or
all to the left to the extreme HIor LO
position to use the maximum heating or
maximum cooling functions:
HI function (maximum heating):
select by turning the temperature knob
clockwise over the maximum value
(32 °C).
This function may be used to heat up the
passenger compartment exploiting the
system potential to the maximum. In this
condition, the system stop controlling
temperature automatically and sets air
mixing to maximum heating. The air speed
and distribution are fixed.
Specifically,
if the heating fluid is not suffi-
ciently warm, the fan will not start up at
the maximum speed immediately to limit
introducing excessively cool air into the
passenger compartment.
All manual settings will be allowed when
this function is on.


46
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
LINEA Owner HAND BOOK RHD.pdf 46LINEA Owner HAND BOOK RHD.pdf 468/21/09 2:16:05 PM8/21/09 2:16:05 PM

Climate control compressor
enabling button (F)
Press to switch the clim ate control
compressor off (if on). The icon on the
display will go out.
Press the button when the LED is off to
res tore aut oma tically system
control
and use of the com pressor.
The icon
will light up on the display in this case.
The system will switch recirculation off
when the compressor is switched off to
prevent misting up.
Although the system
is capable of maintaining the required tem-
perature, the word FULLwill disappear
from the display.
If on the other hand the
system cannot maintain the required tem-
perature, the digits will blink and the word
AUTOwill disappear.IMPORTANT With the compressor off,
it is not possible to introduce air cooler
than ambient temperature into the pas-
senger compartm ent. Furthermore,
in
certain condition s, the windows could
mist up rapidly because the air is not de-
humidified. The switching off of the climate
control compressor remains in storage
even when the engine has been stopped.
To restore automatic compressor control,
press again (in this case, the system will
only work as a heater) or press AUTO.
With climate control compressor off,
the
fan speed can be set to zero manually (no
bar shown).
With the compressor enabled and the en-
gine started, the fan speed may be reduced
to the minimum setting (only one bar
shown).Fast window demisting/defrosting
button (D)
Press this button: the climate control
sys-
tem will automatically switch on all the
functions required for fast windscreen de-misting/defrosting, that is:
switches on climate control compres-
sor when climatic conditions are suit-
able;
air recirculation off;
maximum air temperature HI on both
areas;
operates proper fan speed according
to engine coolant temperature to lim-
it the flow into the passenger
com-
partment of air not warm enough to
demist the windows;
directs air flow to windscreen
and
front side windows vents;
heated rear window on.






49
SAFETY
DEVICES CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
LINEA Owner HAND BOOK RHD.pdf 49LINEA Owner HAND BOOK RHD.pdf 498/21/09 2:16:05 PM8/21/09 2:16:05 PM

WINDSCREEN WASHING
The right stalk fig. 38controls front wind-
screen wiper/washer operation.
WINDSCREEN WASHER/
WIPER
The device can only work when the igni-
tion key is at MAR.
The stalk ring nut can be moved to four
different positions:
Owindscreen wiper off;
intermittent;
continuous slow;
continuous fast.
Move the lever to position A(unstable)
to limit operation for the time for which
the lever is held in this position. The lever
will return to position and the wiper will
be automatically stopped when released.Do not use the windscreen
wiper to remove layers of
snow or ice from the wind-
screen. In such conditions, the
windscreen wiper may be subjected to
excessive stress and the motor protec-
tion which prevents operation for a few
seconds may trip. If operation is not re-
stored, even after turning the key and
restarting the engine, go to a Fiat
Dealership.
With the ring in position the wind-
screen wiper will automatically adapt to
the speed of the car.
IMPORTANT Replace wiper blades as
specified in section “Car maintenance”.
fig. 38F0R0039m
“Smart washing” function
Pull the stalk towards the steering wheel
(unstable position) to operate the wind-
screen washer.
Keeping the stalk pulled for more than half
a second, with just one movement it is
possible to operate the washer jet and the
wiper at the same time.
The wiper stops working three strokes af-
ter releasing the stalk.
A further stroke after 6 seconds
com-
pletes the wiping operation.
53
SAFETY
DEVICES CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
LINEA Owner HAND BOOK RHD.pdf 53LINEA Owner HAND BOOK RHD.pdf 538/21/09 2:16:06 PM8/21/09 2:16:06 PM

ENGINE STARTING
The car is provided with an electronic en-
gine lock device: refer to “The Fiat CODE
system” paragraph in “Dashboard and
controls” if you cannot start the engine.
The engine may be noisier during the first
seconds of operation, particularly after a
long period of inactivity. This is charac-
teristic of hydraulic tappets, the timing sys-
tem chosen to reduce the number of ser-
vicing interventions and does effects nei-
ther functionality nor reliability.
It is advisable not to demand
maximum performance from
your car (e.g. excessive accel-
erations, long distances at top
rpm, excessive intense braking, etc.) as
soon as the engine is started.
Do not leave the key in the ig-
nition switch with the engine
off to avoid unnecessary con-
sumption of electricity which
could drain the battery. It is dangerous
to run the engin e in clo sed environ-
ments.
Running the engine in con-
fined areas is extremely dan-
gerous. The engine consumes oxygen
and produces carbo n monoxide
which is a highly toxic and lethal gas.
WARNING
Remember that the brake
booster and power steering
are not operational until the engine
has been started, therefore much ef-
for t than usual is required on the
brake pedal and steering wheel.
WARNING
STARTING PROCEDURE FOR
PETROL VERSIONS
Proceed as follows:
ensure that the handbrake is up;
put the gear lever into neutral;
press the clutch pedal down to the
floor without touching the accelerator;
turn the ignition key to AV Vand let
it go the moment the engine starts.
If the engine does not start at the first at-
tempt,
return the ignition key to STOP
before repeating starting.




93
CORRECT USE
OF THE CAR
WARNING
IN AN
CAR
TECHNICAL
INDEX
DASHBOARD
SAFETY
LIGHTS AND
EMERGENCY
MAINTENANCE
SPECIFICATIONS
AND CONTROLS
DEVICES
MESSAGES
LINEA Owner HAND BOOK RHD.pdf 93LINEA Owner HAND BOOK RHD.pdf 938/21/09 2:16:13 PM8/21/09 2:16:13 PM