INTRODUCTION/WELCOME
WELCOME FROM CHRYSLER GROUP
LLC ..................... 2
CONTROLS AT A GLANCE
DRIVER COCKPIT.............. 4
INSTRUMENT CLUSTER ..........6
GETTING STARTED
KEYFOB...................8
THEFT ALARM................ 9
SEATBELT ................. 9
CHILD RESTRAINTS ............. 9
FRONTSEATS................13
HEATEDSEATS...............14
TILT STEERING COLUMN ..........15
PROGRAMMABLEFEATURES .......15
OPERATING YOUR VEHICLE
TURN SIGNALS/WIPER/WASHER/HIGH
BEAMSLEVER ...............17
HEADLIGHT SWITCH ............18
SPEED CONTROL ..............19
CLIMATE CONTROLS ........... 20
POWERSUNROOF ............ 20
WIND BUFFETING ..............21
ELECTRONICS
NON-TOUCH-SCREENRADIOS...... 22
NAVIGATION TOUCH-SCREEN RADIO . . .25
STEERING WHEEL AUDIO CONTROLS . . 28
UNIVERSAL GARAGE DOOR OPENER
(HOMELINK
®) .............. 28
POWER OUTLET ............. 30
Uconnect™ Phone ........... 30
VOICECOMMAND .............32
OFF-ROAD CAPABILITIES
FOUR-WHEEL DRIVE OPERATION .....33
UTILITY
REAR CRATE 'N GO®STORAGE ......34
REAR CARGO AREA UTILITY RAILS .....34
TAILGATE ..................34 TRAILER TOWING WEIGHTS (MAXIMUM
TRAILER WEIGHT RATINGS)
........35
RECREATIONAL TOWING (BEHIND
MOTORHOME, ETC.) ............35
BRAKE/TRANSMISSION INTERLOCK
SYSTEM...................37
WHAT TO DO IN EMERGENCIES
24-HOUR TOWING ASSISTANCE
- U.S. ONLY ................ 38
INSTRUMENT CLUSTER WARNING
LIGHTS .................. 38
IF YOUR ENGINE OVERHEATS .......41
JACKINGANDTIRECHANGING...... 42
JUMP-STARTING ............. 48
EMERGENCY TOW HOOKS .........51
TOWINGADISABLEDVEHICLE.......52
FREEING A STUCK VEHICLE ........53
EVENT DATA RECORDER (EDR) ......54
MAINTAINING YOUR VEHICLE
OPENING THE HOOD............55
ENGINE COMPARTMENT ..........56
FLUIDS AND CAPACITIES ..........58
MAINTENANCE CHART .......... 60
FUSES................... 62
TIREPRESSURES..............65
WHEEL AND WHEEL TRIM CARE ......65
EXTERIOR BULBS ............. 66
CONSUMER ASSISTANCE
CHRYSLER GROUP LLC CUSTOMER
CENTER...................67
CHRYSLER CANADA INC. CUSTOMER
CENTER...................67
ASSISTANCE FOR THE HEARING
IMPAIRED..................67
PUBLICATIONS ORDERING .........67
REPORTING SAFETY DEFECTS IN
THE 50 UNITED STATES AND
WASHINGTON, D.C. ........... 68
TIRE WARRANTY ............. 68
MOPAR ACCESSORIES
MOPAR®ACCESSORIES..........71
TABLE OF CONTENTS
Guide Me Home
• Press the NAV hard-key to access the Navigation Main Menu.
• Touch the GUIDE ME HOME soft-key to route you back to your home destination fromyour current location. Touch the GO soft-key to start your trip.
Map
• Press the NAV hard-key to access the Navigation Main Menu.
• Touch the MAP soft-key to display a map of your current position.
STEERING WHEEL AUDIO CONTROLS
• The steering wheel audio controls arelocated on the rear surface of the steering
wheel.
Right Switch
• Press the switch up or down to increase ordecrease the volume.
• Press the button in the center to change modes AM/FM/CD/SAT.
Left Switch
• Press the switch up or down to search forthe next listenable station or select the next
or previous CD track.
• Press the button in the center to select the next preset station (radio) or to change CDs if equipped with a CD Changer.
UNIVERSAL GARAGE DOOR OPENER (HomeLink®)
Programming HomeLink®
Begin Programming
• The HomeLink®buttons are located in the
overhead console.
• The Compass Mini-Trip Computer illuminates the HomeLink
®symbol along
with 1, 2 or 3 indicators under it, when a
HomeLink
®button is pressed. The
indicators will flash at different rates, or
remain solid during programming.
• Erase all channels before you begin progr amming by holding the two outside buttons
for up to 20 seconds until the indicators begin to flash.
ELECTRONICS
28
• Park your vehicle outside of the garage and turn the ignition switch to the ON/RUNposition.
• Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink
®buttons
while keeping the indicator light in view.
• Simultaneously, press and hold both the chosen HomeLink
®button and the
hand-held transmitter button until the HomeLink®indicator flash rate changes from a
slow to a rapidly blinking light, then release both the HomeLink®and the hand-held
transmitter buttons. This may take up to 30 seconds, or longer in rare cases.
• Press and hold the just-programmed HomeLink
®button; if the indicator light stays on
constantly, programming is complete and the garage door should open.
WARNING!
• Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people or pets are in the
path of the door or gate. Only use this transceiver with a garage door opener that
has a “stop and reverse” feature as required by Federal safety standards. This
includes most garage door opener models manufactured after 1982. Do not use a
garage door opener without these safety features. Call toll-free 1–800–355–3515 or,
on the Internet, at www.HomeLink.com for s afety informationor assistance.
• Do not run your vehicle in a closed garage or confined area while programming the transceiver. Exhaust gas from your vehicle contains Carbon Monoxide (CO) which is
odorless and colorless. Carbon Monoxide is poisonous and can cause serious
injury or death when inhaled.
NOTE: If you are having difficulty programming your HomeLink
®and your garage door
opener was manufactured after 1995, you may have a rolling code. Follow the steps
below for Programming A Rolling Code System.
Programming A Rolling Code System
• At the garage door opener motor (in the gara ge), locate the “learn” or “programming”
button. This can usually be found where the hanging antenna wire is attached to the
garage door opener motor (it is NOT the button normally used to open and close the
door).
• Firmly press and release the “learn” or “programming” button. The name and color of
the button may vary by manufacturer. Within 30 seconds, return to the vehicle and
press the programmed HomeLink
®button twice (holding the button for two seconds
each time). If the device is plugged in and activates, programming is complete.
• If the device does not activate, press the button a third time (for two seconds) to
complete the programming.
Using HomeLink®
• To operate, simply press and release the programmed HomeLink®button and the
programmed device will operate.
29
ELECTRONICS