2010 Citroen DS3 DAG run flat

Manual operation
D disappears and the gears engaged appear in succession on the instrument panel. In the event of the engine labouring or over-revving, the gear selected flashes for a few seconds, then the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time. When the vehicle is stationary or moving very slowly, the gearbox selects gear M1automatically. The spor t and snow programmes do not operate in manual mode.
Invalid value during manual operation
 Select position M for sequential changing of the four gears.  Push the lever towards the + sign to change up a gear.  Pull the lever towards the - sign to change down a gear. It is only possible to change from one gear to another if the vehicle speed and engine speed permit; other wise, the gearbox will operate temporarily in automatic mode.
This symbol is displayed if a gear is not engaged correctly (selector between two positions).
Stopping the vehicle
Before switching off the engine, you can engage position P or N to place the gearbox in neutral. In both cases, apply the parking brake to immobilise the vehicle.
When the ignition is on, the lighting of this warning lamp, accompanied by an audible signal and a message on the multifunction screen, indicates a gearbox malfunction. In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel a substantial knock when changing from P to R RRand from N to R . This will not cause any damage to the gearbox. Do not exceed 60 mph (100 km/h), local speed restrictions permitting. Contact a CITROËN dealer as soon as possible.
Operating fault
If the lever is not in position P , Pwhen the driver's door is opened or approximately 45 seconds after the ignition is switched off, a message appears in the multifunction screen.  Return the lever to position P ; the
message disappears.
There is a risk of damage to the gearbox:
- if you press the accelerator and brake pedals at the same time, - if you force the movement of the gear
lever from the P position to another position when the battery is flat.
To reduce fuel consumption when at a prolonged standstill with the engine running (traffic jam...), put the gear lever in the N position and apply the parking brake.

179Practical information
2. Infl ation
 Adjust the pressure using the compressor (to inflate: switch B in position "I" ; to
deflate: switch B in position "O" and press button C ), in accordance with the vehicle’s tyre pressure label (located on the left hand door aper ture). A loss of pressure indicates that the puncture has not been fully plugged; contact a CITROËN dealer for assistance.
 Remove and stow the kit.  Drive at reduced speed (50 mph [80 km/h] max) limiting the distance travelled to approximately 120 miles (200 km).
 Turn the selector A to the "AIR" position.
 Uncoil the black pipe H fully.  Connect the black pipe to the valve of the wheel.
 Connect the compressor’s electric plug to the vehicle’s 12 V socket.
 Star t the vehicle again and leave the engine running.
 Visit a CITROËN dealer as soon as possible. You must inform the technician that you have used this kit. After inspection, the technician will inform you whether the tyre can be repaired or must be replaced.

Removing the cartridge
 Stow the black pipe.  Detach the angled base from the white pipe.  Suppor t the compressor ver tically.  Unscrew the car tridge from the bottom.
Checking tyre pressures/
inflating accessories
Beware of discharges of fluid. The expiry date of the fluid is indicated
on the car tridge. The sealant car tridge is designed for single use; even if only par tly used, it must be replaced. After use, do not discard the cartridge into the environment, take it to an authorised waste disposal site or a CITROËN dealer. Do not forget to obtain a new sealant car tridge, available from CITROËN dealers.
You can also use the compressor, without injecting any product, to: - check or adjust the pressure of your tyres, - inflate other accessories.
 Connect the compressor’s electrical connector to the vehicle’s 12 V socket.  Star t the vehicle and let the engine run.  Adjust the pressure using the compressor (to inflate: switch B in position "I" ; to deflate: switch B in position "O" and press button C ), according to the vehicle’s tyre
pressure label or the accessory’s pressure label.  Remove the kit then stow it.
 Turn the selector A to the "Air"
position.  Uncoil the black pipe H fully.
 Connect the black pipe to the valve of the wheel or accessory. If necessary, fit one of the adaptors supplied with the kit first.

203Practical information
 Connect one end of the green or black cable to the negative terminal (-) of the slave battery B .  Connect the other end of the green or black cable to the negative terminal (-) of the flat battery A .
 Star t the slave vehicle.  Operate the star ter of the broken down
vehicle and let the engine run.  Wait until the engine returns to idle and disconnect the cables.
Charging the battery using
a battery charger
Batteries contain harmful substances such as sulphuric acid and lead. They must be disposed of in accordance with regulations and must not, in any circumstances, be discarded with household waste. Take used remote control batteries and vehicle batteries to a special collection point.
 Disconnect the battery from the vehicle.
 Follow the instructions for use provided by the manufacturer of the charger.  Reconnect star ting with the negative terminal (-).  Check that the terminals and connectors are clean. If they are covered with sulphate (whitish or greenish deposit), remove them
and clean them.
The Stop & Star t battery does not have to be disconnected for charging. It is advisable to disconnect the battery if the vehicle is to be left unused for more than one month.

205Practical information
Energy economy mode
System which manages the period of use of cer tain fu nctions to conser ve a sufficient level of charge in the battery. After the engine has stopped, you can still use func tions such as the audio equipment, windscreen wipers, dipped beam headlamps, cour tesy lamps, etc. for a maximum combined period of thir ty mi nutes.
This period may be greatly reduced if the battery is not fully charged.
A flat battery prevents the engine from star ting (refer to the corresponding paragraph).
If the telephone is being used at the same time on the MyWay audio navigation system, it will be interrupted after 10 minutes.
Switching to economy mode
Once this period has elapsed, a message
appears on the multifunction screen indicating that the vehicle has switched to economy mode and the active functions are put on standby.
Exiting economy mode
These functions are reactivated automatically
the next time the vehicle is driven.  In order to resume the use of these functions immediately, star t the engine and let it run for a few minutes. The time available to you will then be double the period for which the engine is left running. However, this period will always be between five and thir ty minutes.