2010 CITROEN C4 PICASSO gearbox

Downloaded from www.Manualslib.com manuals search engine IX
159
DRIVING

Manual operation

Position of the gear lever for manual
gear changing.


)
Move the gear lever to
position M
.
)
Pull the " +
" paddle to change up
a gear.

)
Pull the " -
" paddle to change
down a gear.


- If the vehicle stops or reduces
speed (for example when ap-
proaching a stop sign), the gear-
box changes down automatically
to fi rst gear.

- In manual mode, it is not neces-
sary to release the accelerator
during gear changes.

- A request to change gear is ac-
cepted only if the engine speed
permits it.
- For safety reasons, depending
on the engine speed, a change
up or down may be performed
automatically.

- It is possible at any time to
change mode, by moving the
gear lever from position D
to po-
sition M
or vice versa.


Flashing of the indicator for
the position requested sig-
nals that this position is not
yet obtained.
If the indicator is on fi xed, the posi-
tion is confi rmed.
Display of a dash in the rev counter
indicates a malfunction. Contact
a CITROËN dealer or a qualifi ed
workshop.
Illumination of the service warning
lamp accompanied by a message
and an audible signal indicates an
operating fault. In this case:


- a marked snatching may be felt
when selecting R
for reverse
gear,

- the gearbox is locked in one
gear,

- do not exceed a speed of 60 mph
(approximately 100 km/h).
Have it checked by a CITROËN
dealer or a qualifi ed workshop.

Downloaded from www.Manualslib.com manuals search engine IX
164
DRIVING
CRUISE CONTROL
System which automatically main-
tains the vehicle speed programmed
by the driver, without any action on
the accelerator pedal.
The cruise control is switched on
manually: the vehicle speed must
be at least 25 mph (approximately
40 km/h) and you must engage:


- fourth gear on a manual gear-
box,

- second gear, in manual mode,
on an electronic or automatic
gearbox,

- position A
on an electronic gear-
box or D
on an automatic gearbox.


Steering mounted controls

The cruise control switches are lo-
cated on the left-hand side of the
steering wheel. The programmed information is
grouped together in zone A
of the
instrument panel screen.


Displays in the instrument
panel

Activation
You can then release the accelera-
tor pedal. The vehicle will automati-
cally keep to the speed chosen.
The speed of your vehicle may vary
slightly in relation to that memo-
rised.
You can adjust the memorised speed
in the instrument panel screen by
pressing:


)
button 4
to increase the speed,

)
button 2
to decrease the speed.
Successive presses modify the
cruise speed in steps of 1 mph
(1 km/h) and a sustained press in
steps of 3 mph (5 km/h).


Deactivation



)
Either by pressing the brake or
the clutch pedal.

)
Or by pressing button 3
.

)
Or if either the ESP or the ASR
system is active.
The cruise control is not active if the
gear lever is in neutral. On selection of the
function via control 1,
no cruise speed has
yet been memorised.



Programming

Rotate the control 1
to the "REG"

position.
Once the desired speed has been
reached using the accelerator, press
button 2
or 4
. The cruise speed is
then memorised. It is displayed in
zone A
of the instrument panel. These actions cause
the information "OFF"

to appear in the instru-
ment panel screen.
These actions do not
cancel the cruise speed
which remains displayed
in the instrument panel.
The cruise control cannot, in any cir-
cumstances, take the place of the
observance of speed limits or of the vig-
ilance and responsibility of the driver.

Downloaded from www.Manualslib.com manuals search engine X
182
CHECKS















Brake pads

Brake wear depends on
the style of driving, par-
ticularly in the case of ve-
hicles used in town, over
short distances. It may be
necessary to have the condition of
the brakes checked, even between
vehicle services.
Unless there is a leak in the circuit, a
drop in the brake fl uid level indicates
that the brake pads are worn.







Manual gearbox

The gearbox does not re-
quire any maintenance (no
oil change).






6-speed electronic
gearbox system
The gearbox does not re-
quire any maintenance (no
oil change).






Automatic gearbox

The gearbox does not re-
quire any maintenance (no
oil change).

Brake disc wear

For information on checking
brake disc wear, contact a
CITROËN dealer or a quali-
fi ed workshop.






















Electric parking brake

This system does not require any
routine servicing. However, in the
event of a problem, have the system
checked by a CITROËN dealer or a
qualifi ed workshop.
For more information, see "Driving -
Electric parking brake - § Operating
faults". Refer to the servicing booklet for the
details of the level checking interval
for this component.
Refer to the servicing booklet for de-
tails of the checking interval for this
component.
Refer to the servicing booklet for de-
tails of the level checking interval for
this component.

Downloaded from www.Manualslib.com manuals search engine XI
188
PRACTICAL INFORMATION












Removing a wheel



)
Park the vehicle on level, stable
and non-slippery ground. Apply
the parking brake (a message
and a warning lamp appear on
the instrument panel).
Switch off the ignition and en-
gage fi rst gear or reverse gear
depending on the slope (posi-
tion P
if an automatic gearbox,
D
or R
if a 6-speed electronic
gearbox).

)
Use a chock to secure the vehi-
cle more safely. Place the chock
9
in front of the wheel that is op-
posite the wheel affected.
)
Detach the trim using the remov-
ing tool 4
, pulling in the area of
the valve.
For vehicles with alloy wheels,
insert the trim removing tool 1

into the recess in the central trim
and lever it off.
For vehicles with alloy wheels
that have visible bolts, remove
the chrome covers using the re-
moving tool 2
.
)
Slacken the wheel bolts. For ve-
hicles with alloy wheels, undo
the security bolts using the secu-
rity socket 6
.

)
Position the jack under the vehi-
cle, at the jacking point A
closest
to the wheel to be changed.

)
Unwind the jack 5
until its brack-
et is in contact with the ground.
Make sure that the jack is verti-
cal under the jacking point used.

)
Continue to extend the jack so
as to raise the vehicle.

)
Undo the wheel bolts and re-
move the wheel.

Before any operation of this
sort, it is advisable to deactivate
your pneumatic suspension.

Downloaded from www.Manualslib.com manuals search engine XI
198
PRACTICAL INFORMATION

Fuses under the dashboard


Access to the fuses


)
Undo the screw by a quarter turn
and pivot the housing.

Table of fuses



Fuse N°



Rating



Functions




F1



15 A

Rear screen wipe


F2



30 A

Locking and unlocking earth


F3



5 A

Airbags and pretensioners


F4



10 A

Multimedia, photochromatic rear view mirror,
particle fi lter, diagnostic socket, air conditioning,
manual headlamp height adjustment


F5



30 A

Front windows, front door electronic control panel,
panoramic sunroof


F6



30 A

Rear windows


F7



5 A

Interior lamps, cooled glovebox, radio


F8



20 A

Multifunction screen, radio, steering mounted
controls, multimedia, under infl ation detection,
alarm, trailer


F9



30 A

Multimedia, front 12 V sockets, torch, radio


F10



15 A

Height corrector (suspension)


F11



15 A

Brake switch, ignition switch


F12



15 A

Parking sensors, automatic wipers and lighting,
passenger’s electric seat, lane departure warning
system, Hi-Fi amplifi er, trailer


F13



5 A

Engine relay unit (BSM), driver’s electric seat


F14



15 A



Air conditioning, Bluetooth ®
hands-free system, automatic
gearbox selector lever, airbags, instrument panel


F15



30 A

Locking and unlocking


F16



-

SHUNT


F17



40 A

Heated rear screen

Downloaded from www.Manualslib.com manuals search engine XI
201
PRACTICAL INFORMATION


Fuse N°



Rating



Functions




F1



20 A

Engine management


F2



15 A

Horn


F3



10 A

Screenwash pump


F4



20 A

Headlamp wash pump


F5



15 A

Engine components


F6



10 A

Xenon dual-function directional headlamps, automatic headlamp height adjustment,
clutch switch, protection switch box (BCP)


F7



10 A

Automatic gearbox, engine coolant level switch, power steering


F8



25 A

Starter motor


F9



10 A

Stop lamp switch


F10



30 A

Engine components


F11



40 A

Rear blower


F12



30 A

Screen wipe


F13



40 A

Built-in Systems Interface (BSI)


F14



30 A

Air pump, heat exchange saver


F15



10 A

Right-hand main beam


F16



10 A

Left-hand main beam


F17



15 A

Left-hand dipped beam


F18



15 A

Right-hand dipped beam


F19



15 A

Engine components


F20



10 A

Engine components


F21



5 A

Cooling fan relay
Table of fuses

Downloaded from www.Manualslib.com manuals search engine XI
202
PRACTICAL INFORMATION

Fuses on the battery


After any operation, carefully refi t
the cover. If the cover is not cor-
rectly positioned or not properly
closed, this could cause serious
problems on your vehicle. For the
same reason, take care not to spill
any liquid in the fusebox.



Table of fuses

Access to the fuses


)
Detach and remove the cover.
Fuses F1
to F6
are located on
the small board, clipped verti-
cally on the battery fusebox.
Fuses F7
to F12
are midi-
fuses. All work on these
fuses must be carried out
by a CITROËN dealer or a
qualifi ed workshop.


Fuse N°



Rating



Functions




F1



5 A

Automatic gearbox actuator


F2



5 A

Stop switch


F3



5 A

Battery charge estimation ECU


F4



20 A

ESP supply


F5



5 A

ESP supply


F6



20 A

ECU for 6-speed electronic gearbox/automatic gearbox

Downloaded from www.Manualslib.com manuals search engine XI
203
PRACTICAL INFORMATION
12 V BATTERY
Procedure for starting the engine
using another battery or for charging
your fl at battery.


The Stop & Start battery does not
have to be disconnected for charging.







The presence of this label, in
particular with the Stop & Start
system, indicates the use of
a 12 V lead-acid battery with
special technology and specifi cation;
the involvement of a CITROËN deal-
er or a qualifi ed workshop is essential
when replacing or disconnecting the
battery.

After refi tting the battery, the Stop &
Start system will only be active after
a continuous period of immobilisa-
tion of the vehicle, a period which
depends on the climatic conditions
and the state of charge of the bat-
tery (up to about 8 hours).

*

or position P
for an automatic gearbox.


Access to the battery

Before doing any work
Immobilise the vehicle: ap-
ply the parking brake, put
the gearbox in neutral * , then switch
off the ignition.
Check that all electrical equipment
is switched off.


Check that the battery posts and
terminals are clean. If they are cov-
ered with sulphate (white or green
deposit), disconnect them and
clean them.

Batteries contain harmful
substances such as sul-
phuric acid and lead. They
must be disposed of in accordance
with regulations and must not, in
any circumstances, be discarded
with household waste.
Take used cell batteries and vehi-
cle batteries to an authorised col-
lection point.
The battery is located under the
bonnet.
For access to the (+) terminal:


)
Release the bonnet using the
interior lever, then the exterior
safety catch,

)
raise the bonnet and secure it
with its stay,

)
lift the plastic cover for access to
the (+) terminal.