2010 CADILLAC DTS warning

Spare Tire
Compact Spare Tire
{WARNING:
Driving with more than one compact spare tire
at a time could result in loss of braking and
handling. This could lead to a crash and you or
others could be injured. Use only one compact
spare tire at a time.
This vehicle may have a compact spare tire. Although thecompact spare tire was fully inflated when the vehiclewas new, it can lose air after a time. Check the inflationpressure regularly. It should be 60 psi (420 kPa).
After installing the compact spare on the vehicle, stopas soon as possible and make sure the spare tireis correctly inflated. The compact spare is made toperform well at speeds up to 65 mph (105 km/h)for distances up to 3,000 miles (5 000 km), so you canfinish your trip and have the full-size tire repaired orreplaced at your convenience. Of course, it is bestto replace the spare with a full-size tire as soon aspossible. The spare tire will last longer and be in goodshape in case it is needed again.
Notice:When the compact spare is installed, donot take the vehicle through an automatic car washwith guide rails. The compact spare can getcaught on the rails which can damage the tire,wheel and other parts of the vehicle.
Do not use the compact spare on other vehicles.
And do not mix the compact spare tire or wheel withother wheels or tires. They will not fit. Keep thespare tire and its wheel together.
Notice:Tire chains will not fit the compact spare.Using them can damage the vehicle and can damagethe chains too. Do not use tire chains on thecompact spare.
6-90

Care of Safety Belts
Keep belts clean and dry.
{WARNING:
Do not bleach or dye safety belts. It may severely
weaken them. In a crash, they might not be able
to provide adequate protection. Clean safety belts
only with mild soap and lukewarm water.
Weatherstrips
Silicone grease on weatherstrips will make them lastlonger, seal better, and not stick or squeak. Applysilicone grease with a clean cloth. During very cold,damp weather frequent application may be required. SeeRecommended Fluids and Lubricants on page 7-8.
Washing Your Vehicle
The best way to preserve the vehicle’s finish is to keepit clean by washing it often.
Notice:Certain cleaners contain chemicals that candamage the emblems or nameplates on the vehicle.Check the cleaning product label. If it states thatit should not be used on plastic parts, do not use iton the vehicle or damage may occur and it wouldnot be covered by the warranty.
Do not wash the vehicle in direct sunlight. Use a carwashing soap. Do not use cleaning agents thatare petroleum based or that contain acid or abrasives,as they can damage the paint, metal or plastic onthe vehicle. Approved cleaning products can be obtainedfrom your dealer/retailer. Follow all manufacturers’directions regarding correct product usage, necessarysafety precautions and appropriate disposal of anyvehicle care product.
Rinse the vehicle well, before washing and after toremove all cleaning agents completely. If they areallowed to dry on the surface, they could stain.
Dry the finish with a soft, clean chamois or an all-cottontowel to avoid surface scratches and water spotting.
High pressure car washes may cause water to enterthe vehicle. Avoid using high pressure washescloser than 12 inches (30 cm) to the surface of the
6-95

To reinstall the rear seat cushion, do the following:
{WARNING:
A safety belt that is not properly routed through
the seat cushion or is twisted will not provide the
protection needed in a crash. If the safety belt has
WARNING: (Continued)
WARNING: (Continued)
not been routed through the seat cushion at all, it
will not be there to work for the next passenger.
The person sitting in that position could be badly
injured. After reinstalling the seat cushion, always
check to be sure that the safety belts are properly
routed and are not twisted.
1. Buckle the center passenger position safety belt,then route the safety belts through the proper slotsin the seat cushion. Do not let the safety beltsget twisted.
2. Slide the rear of the cushion up and under theseatback so the rear-locating guides hook intothe wire loops on the back frame.
3. With the seat cushion lowered, push rearward andthen press down on the seat cushion until thespring locks on both ends engage.
4. Check to make sure the safety belts are properlyrouted and that no portion of any safety belt istrapped under the seat. Also make sure the seatcushion is secured.
6-105

Maintenance Schedule
Introduction
Notice:Maintenance intervals, checks, inspections,recommended fluids, and lubricants are necessaryto keep this vehicle in good working condition.Damage caused by failure to follow scheduledmaintenance might not be covered by thevehicle warranty.
Proper vehicle maintenance helps to keep the vehicle ingood working condition, improves fuel economy, andreduces vehicle emissions for better air quality.
Because of all the different ways people use vehicles,maintenance needs vary. The vehicle might needmore frequent checks and services. Please read theinformation under Scheduled Maintenance. To keep thevehicle in good condition, see your dealer/retailer.
The maintenance schedule is for vehicles that:
•carry passengers and cargo within recommended
limits on the Tire and Loading Information label.SeeLoading the Vehicle on page 5-18.
•are driven on reasonable road surfaces within legal
driving limits.
•use the recommended fuel. SeeGasoline Octane
on page 6-5.
{WARNING:
Performing maintenance work on a vehicle can be
dangerous. In trying to do some jobs, you can be
seriously injured. Do your own maintenance work
only if you have the required know-how and the
proper tools and equipment for the job. If you have
any doubt, see your dealer/retailer to have a
qualified technician do the work. SeeDoing Your
Own Service Work on page 6-4.
At your General Motors dealer/retailer, you can becertain that you will receive the highest level of serviceavailable. Your dealer /retailer has specially trainedservice technicians, uses genuine GM replacementparts, as well as, up to date tools and equipmentto ensure fast and accurate diagnostics.
The proper replacement parts, fluids, and lubricants touse are listed inRecommended Fluids and Lubricantson page 7-8andMaintenance Replacement Partson page 7-10. We recommend the use of genuine partsfrom your dealer/retailer.
7-2

First Engine Oil Change After Every
120 000 km/75,000 Miles
•Professional Vehicle Only: Engine cooling system
drain, flush, and refill, cooling system and cappressure check, and cleaning of outside of radiatorand air conditioning condenser (or every 5 years,whichever occurs first). SeeEngine Coolanton page 6-23.An Emission Control Service.
First Engine Oil Change After Every
160 000 km/100,000 Miles
•Automatic transmission fluid and filter change
(normal service). SeeAutomatic Transmission Fluidon page 6-19.
•Spark plug replacement.An Emission Control
Service.
First Engine Oil Change After Every
240 000 km/150,000 Miles
•Except Professional Vehicle: Engine cooling system
drain, flush, and refill, cooling system and cappressure check, and cleaning of outside of radiatorand air conditioning condenser (or every 5 years,whichever occurs first). SeeEngine Coolanton page 6-23.An Emission Control Service.
•Engine accessory drive belt inspection for fraying,
excessive cracks, or obvious damage andreplacement, if needed.An Emission ControlService.
Owner Checks and Services
Starter Switch Check
{WARNING:
When you are doing this inspection, the vehicle
could move suddenly. If the vehicle moves, you or
others could be injured.
1. Before starting this check, be sure there is enoughroom around the vehicle.
2. Firmly apply both the parking brake and the regularbrake. SeeParking Brake on page 3-30.
Do not use the accelerator pedal, and be ready toturn off the engine immediately if it starts.
3. Try to start the engine in each gear. The vehicleshould start only in P (Park) or N (Neutral). If thevehicle starts in any other position, contactyour dealer/retailer for service.
7-6

Automatic Transmission Shift Lock
Control System Check
{WARNING:
When you are doing this inspection, the vehicle
could move suddenly. If the vehicle moves, you or
others could be injured.
1. Before starting this check, be sure there is enoughroom around the vehicle. It should be parked on alevel surface.
2. Firmly apply the parking brake. SeeParking Brakeon page 3-30.
Be ready to apply the regular brake immediately ifthe vehicle begins to move.
3. With the engine off, turn the ignition to ON/RUN,but do not start the engine. Without applying theregular brake, try to move the shift lever outof P (Park) with normal effort. If the shift levermoves out of P (Park), contact your dealer/retailerfor service.
Ignition Transmission Lock Check
While parked, and with the parking brake set, try to turnthe ignition to LOCK/OFF in each shift lever position.
•The ignition should turn to LOCK/OFF only
when the shift lever is in P (Park).
•The ignition key should come out only
in LOCK/OFF.
Contact your dealer/retailer if service is required.
7-7

Parking Brake and Automatic
Transmission P (Park)
Mechanism Check
{WARNING:
When you are doing this check, the vehicle could
begin to move. You or others could be injured and
property could be damaged. Make sure there is
room in front of the vehicle in case it begins to roll.
Be ready to apply the regular brake at once
should the vehicle begin to move.
Park on a fairly steep hill, with the vehicle facingdownhill. Keeping your foot on the regular brake, set theparking brake.
•To check the parking brake’s holding ability:
With the engine running and the transmissionin N (Neutral), slowly remove foot pressure from theregular brake pedal. Do this until the vehicle isheld by the parking brake only.
•To check the P (Park) mechanism’s holding ability:
With the engine running, shift to P (Park). Thenrelease the parking brake followed by theregular brake.
Contact your dealer/retailer if service is required.
Recommended Fluids and
Lubricants
Fluids and lubricants identified below by name, partnumber, or specification can be obtained from yourdealer/retailer.
UsageFluid/Lubricant
Engine Oil
The engine requires a specialengine oil meeting GM StandardGM4718M. Oils meeting thisstandard can be identified assynthetic, and should also beidentified with the AmericanPetroleum Institute (API) Certifiedfor Gasoline Engines starburstsymbol. However, not all syntheticAPI oils with the starburst symbolwill meet this GM standard. Look forand use only oil that meets GMStandard GM4718M. For the properviscosity, seeEngine Oil onpage 6-13.
Engine Coolant
50/50 mixture of clean, drinkablewater and use only DEX-COOL®
Coolant. SeeEngine Coolant onpage 6-23.
Hydraulic BrakeSystem
DOT 3 Hydraulic Brake Fluid(GM Part No. U.S. 88862806, inCanada 88862807).
7-8

A
Accessories and Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3Accessory Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24Accessory Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34Adaptive Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6Add-On Electrical Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-100Air Cleaner/Filter, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17Air Filter, Passenger Compartment . . . . . . . . . . . . . . . . . . . . 4-44AirbagAdding Equipment to YourAirbag-Equipped Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-73Airbag SystemHow Does an Airbag Restrain? . . . . . . . . . . . . . . . . . . . . . . 2-65Passenger Sensing System . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-67Servicing Your Airbag-Equipped Vehicle . . . . . . . . . . 2-72What Makes an Airbag Inflate? . . . . . . . . . . . . . . . . . . . . . . 2-65What Will You See After an Airbag Inflates? . . . . 2-66When Should an Airbag Inflate? . . . . . . . . . . . . . . . . . . . . 2-63Where Are the Airbags? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60AirbagsPassenger Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-51Readiness Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-50System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-58Analog Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
AntennaBackglass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-121Antenna, XM™ Satellite Radio Antenna System . . . 4-121Antilock Brake System (ABS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4Warning Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53Appearance CareAluminum or Chrome-Plated Wheels . . . . . . . . . . . . . . 6-97Care of Safety Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-95Chemical Paint Spotting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-99Cleaning Exterior Lamps/Lenses . . . . . . . . . . . . . . . . . . . . 6-96Fabric/Carpet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-92Finish Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-96Finish Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-98Instrument Panel, Vinyl, and OtherPlastic Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-94Interior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-91Leather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-93Sheet Metal Damage . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-98Speaker Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-94Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-98Underbody Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-98Washing Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-95Weatherstrips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-95Windshield and Wiper Blades . . . . . . . . . . . . . . . . . . . . . . . . 6-97Wood Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-94Ashtray(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
1