2010 CADILLAC DTS instrument cluster

Turn Signal On Chime
If the turn signal is left on, a warning chime sounds andthe Driver Information Center (DIC) will display TURNSIGNAL ON after driving about a mile as a reminder toturn it off. SeeDIC Warnings and Messages onpage 4-67.
Headlamp High/Low-Beam Changer
Push forward to change the headlamps from lowbeam to high. Pull the lever back and then release it tochange from high beam to low.
This light on the instrumentpanel cluster will be on,indicating high-beamusage.
Forward Collision Alert (FCA)
System
If your vehicle has this feature, be sure to read thisentire section before using it.
The system operates on a radio frequency subject toFederal Communications Commission (FCC) Rules andwith Industry Canada.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,including interference that may cause undesiredoperation of the device.
This device complies with RSS-210 of Industry Canada.Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,including interference that may cause undesiredoperation of the device.
Changes or modifications to this system by other thanan authorized service facility could void authorization touse this equipment.
4-6

Cruise Control
With cruise control, a speed of approximately 40 km/h(25 mph) or more can be maintained without keepingyour foot on the accelerator. Cruise control does not workat speeds below about 40 km/h (25 mph). A cruise controllight appears in the instrument panel cluster when thecruise control is on.
When the brakes are applied, the cruise controlshuts off.
{WARNING:
Cruise control can be dangerous where you
cannot drive safely at a steady speed. So, do not
use the cruise control on winding roads or in
heavy traffic.
Cruise control can be dangerous on slippery roads.
On such roads, fast changes in tire traction can
cause excessive wheel slip, and you could lose
control. Do not use cruise control on slippery roads.
If your vehicle is in cruise control when the TractionControl System (TCS) begins to limit wheel spin,the cruise control automatically turns off. SeeTractionControl System (TCS) on page 5-6. When roadconditions let you safely use it again, the cruise controlcan be turned back on.
Setting Cruise Control
{WARNING:
If you leave your cruise control on when you are
not using cruise, you might hit a button and go
into cruise when you do not want to. You could be
startled and even lose control. Keep the cruise
control switch off until you want to use cruise
control.
4-12

The cruise control buttonsare located on left side ofthe steering wheel.
I(On):Turns on the cruise control system.
+ RES (Resume/Accelerate):Press to make thevehicle accelerate or resume to a previously set speed.
SET– (Set):Press to set the speed.
[(Cancel):Press to cancel cruise control.
Cruise control will not work if the parking brake is set, orif the master cylinder brake fluid level is low.
If the brakes are applied, the cruise control shuts off.
The cruise light on the instrument panel cluster comeson after the cruise control has been set to the desiredspeed.
1. PressI.
2. Get up to the desired speed.
3. Press the SET– button located on the steeringwheel and release it.
4. Take your foot off the accelerator.
Resuming a Set Speed
Suppose the cruise control is set at a desired speedand then the brakes are applied. This shuts off thecruise control. But it does not need to be reset.
Once the vehicle is traveling approximately 40 km/h(25 mph) or more, press the +RES (resume/accelerate)button to return to the desired preset speed. Thecruise light displays again.
The vehicle returns to and stays at the preset speed. Ifyou press and hold the +RES button, the vehicle speedincreases until the button is released or the brake isapplied. Do not hold in the +RES button, if you do notwant the vehicle speed to increase.
4-13

AUTO (Automatic):Automatically turns on theheadlamps at normal brightness, together with thefollowing:
•Parking Lamps
•Instrument Panel Lights
•IntelliBeam™
;(Parking Lamps):Turns on the parking lamps
together with the following:
•Instrument Panel Lights
•License Plate Lamps
•Taillamps
•Side Marker Lamps
The parking brake indicator light comes on and stays onwhile the parking lamps are on with the engine offand the ignition in ACC/ACCESSORY or ON/RUN.
2(Headlamps):Turns on the headlamps together with
the previously listed lamps. A warning chime soundsif the driver’s door is opened while the ignition switch isoff and the headlamps are on.
#(Fog Lamps):Press the exterior lamps control to
turn on the fog lamps. SeeFog Lamps on page 4-30.
IntelliBeam™ Intelligent High-Beam
Headlamp Control System
For vehicles with this feature, be sure to read this entiresection before using it.
IntelliBeam is an enhancement to the vehicle’sheadlamp system. Using a digital light sensor on therearview mirror, this system turns the vehicle’shigh-beam headlamps on and off according tosurrounding traffic conditions.
The IntelliBeam system turns the high-beam headlampson when it is dark enough, there is no other trafficpresent, and the IntelliBeam system is enabled.
Turning On and Enabling IntelliBeam™
Press and release the IntelliBeam button on the insiderear view mirror. The IntelliBeam indicator on themirror turns on to indicate the system is on. Once thesystem has been turned on, it remains on each time thevehicle is started, but the IntelliBeam system must beenabled.
To enable the IntelliBeam system, turn the exterior lampcontrol to AUTO, with the turn signal/multifunctionlever in its neutral position. The High-Beam On Lightappears on the instrument panel cluster when thehigh-beams are on. SeeHighbeam On Light onpage 4-61.
4-26

Wiper Activated Headlamps
This feature activates the headlamps and parking lampsafter the windshield wipers are turned on and havecompleted eight wipe cycles within four minutes.
When the ignition is turned to LOCK/OFF, thewiper-activated headlamps immediately turn off. Thewiper-activated headlamps also turn off if the windshieldwipers are turned off.
Headlamps on Reminder
A warning chime will sound if the exterior lamp controlis left on in either the headlamp or parking lamp positionand the driver’s door is opened with the ignition off.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier forothers to see the front of your vehicle during theday. Fully functional daytime running lamps are requiredon all vehicles first sold in Canada.
The DRL system makes the turn signal lamps come onwhen the following conditions are met:
•It is still daylight and the ignition is on.
•The exterior lamp control is in the off position.
•The transmission is not in P (Park)
(United States only).
•The light sensor is covered or not detecting light.
See “Sensors” underDual Climate Control Systemon page 4-36.
When DRL are on, no other exterior lamps such as theparking lamps, taillamps, etc. will be on when theDRL are being used. The instrument panel will not be litup either.
When automatic lighting is on and it is dark enoughoutside, the turn signal lamps turn off and normallow-beam headlamp operation occurs.
When automatic lighting is on and it is bright enoughoutside, the regular lamps go off, and the DRLtakes over. If the vehicle is started in a dark garage, theautomatic headlamp system comes on immediately.Once you leave the garage, it will take approximatelyone minute for the automatic headlamp system tochange to DRL if there is light outside. During that delay,the instrument panel cluster may not be as bright asusual. Make sure the instrument panel brightness knobis in the full bright position. SeeInstrument PanelBrightness on page 4-31.
Turning on automatic lighting or the headlamps willdeactivate the DRL. If the parking lamps or thefog lamps were turned on instead, the DRL will stilldeactivate.
4-29

To idle the vehicle with the DRL off at night, turn offautomatic lighting and shift the transmission into P (Park).Placing the vehicle in P (Park) disables the DRL. TheDRL will stay off until the vehicle is shifted out of P (Park).
To drive the vehicle with the DRL off, turn off automaticlighting and manually turn on the parking lamps orfog lamps, if the vehicle has them.
The regular headlamp system should be turned onwhen needed.
Fog Lamps
The fog lamps button is on the exterior lamps control tothe left of the steering column.
#(Fog Lamps):Press the exterior lamps button to
turn the fog lamps on or off. A light comes on inthe instrument panel cluster when the fog lamps are inuse. SeeInstrument Panel Cluster on page 4-47.The ignition must be in the ON/RUN position for thefog lamps to work.
The fog lamps will go off when the headlamps arechanged to high-beam.
Some localities have laws that require the headlamps tobe on along with the fog lamps.
Cornering Lamps
The cornering lamps come on when the headlamps orparking lamps are on and you signal a turn with themultifunction lever. They provide more light forcornering.
Exterior Lighting Battery Saver
If the exterior lamp button has been left on, the exteriorlamps will turn off about 10 minutes after the ignitionis turned to LOCK/OFF and a door has been opened.This protects against draining the battery if theheadlamps or parking lamps are accidentally left on.If you need to leave the lamps on for more than10 minutes, use the exterior lamp control to turn thelamps back on after the ignition is turned to LOCK/OFFand any door is opened.
4-30

Reading Lamps
The reading lamps are located on the overhead consoleon the headliner and in the rear door opening. Theselamps come on automatically when any door is openedand it is dark outside.
For manual operation, press the button to turn them on.Press it again to turn them off.
If the reading lamps are left on, they automatically shutoff 10 minutes after the ignition has been turned off.
Footwell Lamps
For vehicles with footwell lamps, they are located underthe instrument panel and at the rear of the frontseats. These lamps provide soft light to the front andrear floor areas. They dim with the instrument panelcluster lights.
Footwell lighting brightness can be adjusted with theinstrument panel brightness control located belowthe exterior lamps control. SeeInstrument PanelBrightness on page 4-31. The footwell lights will turn offbefore the instrument panel lights are at their lowestlevel of brightness.
Battery Load Management
This feature monitors the vehicle’s electrical load anddetermines when the battery is in a heavy dischargecondition. During times of high electrical loading,the engine may idle at a higher revolutions per minute(rpm) setting than normal to make sure the batterycharges. High electrical loads may occur when severalof the following are on: headlamps, high beams, foglamps, rear window defogger, the climate control fan athigh speeds, heated seats and engine cooling fans.
If the battery continues to discharge, even withthe engine idling at a higher rpm setting, some electricalloads will automatically be reduced. When this occurs,the rear window defogger may take slightly longerto clear the glass, the heated seats may not get as warmas they usually do and the climate control fan may cutback to a lower speed. For more battery savinginformation, see “Battery Saver Active Message” underDIC Warnings and Messages on page 4-67.
4-32

Instrument Panel Cluster
United States version shown, Canada similar
4-47