2010 CADILLAC DTS fuse

Power Steering Fluid
The power steering fluidreservoir is located next tothe underhood fuseblock on the passengerside of the vehicle.SeeEngine CompartmentOverview on page 6-12for more informationon location.
When to Check Power Steering Fluid
It is not necessary to regularly check power steering fluidunless you suspect there is a leak in the system oryou hear an unusual noise. A fluid loss in this systemcould indicate a problem. Have the system inspectedand repaired.
How to Check Power Steering Fluid
To check the power steering fluid:
1. Turn the key off and let the engine compartmentcool down.
2. Wipe the cap and the top of the reservoir clean.
3. Unscrew the cap and wipe the dipstick with a cleanrag.
4. Replace the cap and completely tighten it.
5. Remove the cap again and look at the fluid level onthe dipstick.
The level should be at the FULL COLD mark. Ifnecessary, add only enough fluid to bring the level up tothe mark.
What to Use
To determine what kind of fluid to use, seeRecommended Fluids and Lubricants on page 7-8.Always use the proper fluid.
Notice:Use of the incorrect fluid may damage thevehicle and the damages may not be covered bythe vehicle’s warranty. Always use the correct fluidlisted inRecommended Fluids and Lubricantson page 7-8.
6-30

Properly torqued wheel nuts are necessary to helpprevent brake pulsation. When tires are rotated, inspectbrake pads for wear and evenly tighten wheel nuts inthe proper sequence to torque specifications inCapacities and Specifications on page 6-109.
Brake linings should always be replaced as completeaxle sets.
Brake Pedal Travel
See your dealer/retailer if the brake pedal does notreturn to normal height, or if there is a rapid increase inpedal travel. This could be a sign that brake servicemight be required.
Brake Adjustment
Every time the brakes are applied, with or without thevehicle moving, the brakes adjust for wear.
Replacing Brake System Parts
The braking system on a vehicle is complex. Its manyparts have to be of top quality and work well together ifthe vehicle is to have really good braking. The vehiclewas designed and tested with top-quality brake parts.When parts of the braking system are replaced — forexample, when the brake linings wear down and newones are installed — be sure to get new approvedreplacement parts. If this is not done, the brakes mightnot work properly.
For example, if someone puts in brake linings that arewrong for the vehicle, the balance between the front andrear brakes can change — for the worse. The brakingperformance expected can change in many other ways ifthe wrong replacement brake parts are installed.
Battery
Refer to the replacement number on the original batterylabel when a new battery is needed.
{DANGER:
Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals
known to the State of California to cause cancer
and reproductive harm. Wash hands after
handling.
The battery is under the rear seat cushion. To accessthe battery, seeRear Underseat Fuse Block onpage 6-104. Access to the battery is not necessary tojump start the vehicle. SeeJump Starting on page 6-36.
6-34

2. Get the vehicles close enough so the jumper cablescan reach, but be sure the vehicles are not touchingeach other. If they are, it could cause a groundconnection you do not want. You would not be ableto start your vehicle and the bad grounding coulddamage the electrical systems.
To avoid the possibility of the vehicles rolling, setthe parking brake firmly on both vehicles involved inthe jump start procedure. Put an automatictransmission in P (Park) or a manual transmissionin NEUTRAL before setting the parking brake.
Notice:If you leave the radio or other accessorieson during the jump starting procedure, they could bedamaged. The repairs would not be covered by thewarranty. Always turn off the radio and otheraccessories when jump starting the vehicle.
3. Turn off the ignition on both vehicles. Unplugunnecessary accessories plugged into the cigarettelighter or the accessory power outlets. Turn offthe radio and all lamps that are not needed. Thiswill avoid sparks and help save both batteries.And it could save the radio!
4. Open the hoods and locate the positive (+) andnegative (!) terminal locations on the othervehicle. Your vehicle has a remote positive (+) jumpstarting terminal and a remote negative (!) jumpstarting terminal.
The remote positive (+) terminal is located in theengine compartment on the passenger’s side of thevehicle. Lift the red plastic cap to access theterminal. SeeEngine Compartment Overview onpage 6-12for more information on the locationof the remote positive (+) terminal.
A second remote positive (+) terminal is located onthe rear underseat fuse block.
The remote negative (!) terminal is located behindthe power steering pulley, near the engine cover.It is marked GND (!).
4.6L LD8 Engine shown,4.6L L37 Enginesimilar
6-37

Service Parts Identification Label
This label, on the spare tire cover, has the followinginformation:
•Vehicle Identification Number (VIN)
•Model designation
•Paint information
•Production options and special equipment
Do not remove this label from the vehicle.
Electrical System
Add-On Electrical Equipment
Notice:Do not add anything electrical to thevehicle unless you check with your dealer/retailerfirst. Some electrical equipment can damagethe vehicle and the damage would not be coveredby the vehicle’s warranty. Some add-on electricalequipment can keep other components fromworking as they should.
Add-on equipment can drain the vehicle battery, even ifthe vehicle is not operating.
The vehicle has an airbag system. Before attempting toadd anything electrical to the vehicle, seeServicingYour Airbag-Equipped Vehicle on page 2-72andAddingEquipment to Your Airbag-Equipped Vehicle onpage 2-73.
Headlamp Wiring
The headlamp wiring system has four individual fuses.An electrical overload will cause the lamps to go onand off, or in some cases to remain off. If this happens,have the headlamp wiring checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by an internalcircuit breaker. If the wiper motor overheats due toheavy snow, the wipers will stop until the motor coolsand will then restart.
A fuse powers the wiper motor. If the fuse blows, thereis an electrical problem. Be sure to have it fixed.
6-100

Power Windows and Other Power
Options
Circuit breakers in the fuse block protect the powerwindows and other power accessories. When the currentload is too heavy, the circuit breaker opens andcloses, protecting the circuit until the problem is fixed orgoes away.
Fuses and Circuit Breakers
The wiring circuits in the vehicle are protected fromshort circuits by a combination of fuses and circuitbreakers. This greatly reduces the chance of firescaused by electrical problems.
Look at the silver-colored band inside the fuse. If theband is broken or melted, replace the fuse. Be sure youreplace a bad fuse with a new one of the identicalsize and rating.
If you ever have a problem on the road and don’t havea spare fuse, you can borrow one that has the sameamperage. Just pick some feature of the vehicle that youcan get along without — like the radio or cigarettelighter — and use its fuse, if it is the correct amperage.Replace it as soon as you can.
Underhood Fuse Block
The underhood fuse block is located on the passengerside of the engine compartment. Remove the fusecover and secondary service cover to access thefuse block.
Notice:Spilling liquid on any electrical componentson the vehicle may damage it. Always keep thecovers on any electrical component.
6-101

FusesUsage
1Engine Control Module (ECM), Crank
2Fuel Injectors Odd
3Fuel Injectors Even
4Air Conditioning Clutch
FusesUsage
5Air Injection Reactor (AIR) Solenoid
6Oxygen Sensor
7Emission Device
8Transmission, Ignition 1
6-102

FusesUsage
9Engine Control Module (ECM),Powertrain Control Module (PCM)
10Climate Control System, InstrumentPanel Cluster Ignition 1
11Airbag System
12Horn
13Windshield Wiper
14Fog Lamps
15Right High-Beam Headlamp
16Left High-Beam Headlamp
17Left Low-Beam Headlamp
18Right Low-Beam Headlamp
19Windshield Washer Pump Motor
20Left Front Cornering Lamp
21Right Front Cornering Lamp
22Air Pump (J-Case)
23Antilock Brake System (ABS)(J-Case)
FusesUsage
24Starter (J-Case)
25Antilock Brake System (ABS)Motor (J-Case)
26Cooling Fan 2 (J-Case)
27Cooling Fan 1 (J-Case)
RelaysUsage
29Powertrain
30Starter
31Cooling Fan 2
32Cooling Fan 3
33Cooling Fan 1
34Air Conditioning Clutch
35Air Injection Reactor (AIR) Solenoid
36Ignition
37Air Pump
6-103

Rear Underseat Fuse Block
The rear fuse block is located under the rear seat onthe driver side. The rear seat cushion must be removedto access the rear fuse block.
Removing the Rear Seat Cushion
Notice:If you touch the exposed wires with themetal on the seat cushion, you could cause ashort that could damage the battery and or wires.Avoid contact between the rear seat and thefuse center whenever you remove or reinstall therear seat. Do not remove covers from any ofthe covered parts, and do not store anything underthe seats.
To remove the rear seat cushion, do the following:
1. Pull up on the front of the cushion to release thefront hooks.
2. Pull the cushion up and out toward the front ofthe vehicle.
To access the fuse block, pull out and lift up on thecover latch, located at the end of the fuse block, nearthe battery cable.
6-104