2010 AUDI S3 battery

vehicle starts up as long as the malfunction exists. Contact your
authorized Audi dealer and have the malfunction corrected .
For more information
:::::> page 264. •
Electronic power control )f'
This warning/indicat or light m onitors the electronic
power control.
The warning/indicator light (E lectronic Power Controll illumi-
nates when you switch on the ignition as a function check.
[ i ] Tips
If this warning/indicator light illuminates while you are driving, then
there is a malfunction in the engine electronics . Have the malfunc ­
tion corrected as soon as possible by your authorized Audi dealer or
qualified workshop. •
Applies to vehicles : wit h diese l en gine
Glovv plug system / Engine malfunction X-
The indicator lamp lights up to show that the glow plugs
are preheating. It flashes if there is an engine malfunc­
tion.
W arning l ight ~ s ta ys lit up
If the indicator light illuminates , the glow plug system is active .
You should start the engine immediately after the indicator light
switches off. The indicator light only illuminates for approximately 1 second if the engine is warm or if the outside temperature is
above 46 °F (8 °Cl.
T here is a fault in the g low plug system if the warning light does
not light up when the engine is
c old. Contact an authorized Aud i
dea ler or a qualified workshop.
Controls and equip ­
ment
In st rum ent s a nd w arnin g/indi cato r ligh ts
Warn in g light "' flas hes
If a malfunction develops in the engine management system while
you are driving, the glow plug light will flash ......... The engine shou ld
be checked by an authorized Audi dealer or a qua lified workshop as
soon as possible.
& WARNING
If you do not p ay atte nti on to the warning light s th at hav e come
o n, thi s could l ead to per sona l injury or d am age to your vehi cle. •
Electronic Stabilization Program (ESP) r;
The warning/indicator light monitors the electronic stabi­
lization program.
The warning/indicator l ight has the following functions:
• it flashes while you are driving, when the ESP or the ASR (Anti·
Slip Regulation) is working .
• it illuminates when you switch on the ignition for approximate ly
2 seconds as a func tion check .
• it illuminates when there is a ma lfunction in the ESP.
• it illum inates after the battery has been d isconnected .
• it illuminates continuous ly when the ESP is switched off.
• it illuminates if there is a malfunction in the ABS, since the ESP
is part of the ABS system .
If the ESP warning/indicator light illuminates and stays on after you
have started the engine, this may mean that the control system has
temporari ly switched off the ESP. If this is case, you can reactivate
the ESP by switching the ignition off and then on again . The
warning/ indicator light should go out to show that the system is
fully functional again.
The ESP warning/indicator light will i lluminate when the ignition is
switched on if the vehicle battery has been disconnected and then .,,
I • •

Inst rum ents and w arnin g/indi cat or li ghts
reconnected again . The light should go out after driving a short
distance if the steering wheel is turned slight ly .
For more information about the ESP:::::,
page 188. •
Malfunction Indicator Lamp (MIL)
(USA models )/ (Canada models)
The Malfunction Indicator Lamp (M IU is part of the On-Board Diag ­
nostic (OBD Ill system . The symbo l lights up when the ignition is
turned on and wi ll turn off after the engine has started and has
sett led at constant id le speed. This indicates that the MIL is working
proper ly .
The warning light il luminates when there is a malfunction in the
engine electronic system. Contact your authorized Audi dealer and have the malfunction corrected.
For more information :::::,
page 21. •
High beam @:D
The ~Dwarning/ indicato r light illuminates when the h igh beams are
on or when you use the headlight flasher. For more information
about using the h ig h beams , see :::::,
page 57. •
Turn signals ¢ Q
The indicator light flashes when you use ei ther turn
signal.
Whenever you use the left¢ or the right ¢ turn signal, the ind icator
light flashes . When you use the emergency flasher, both indicator
lights flash .
If one of the turn signal light bulbs burn out, the turn signal will
flash twice as fast as no rma l.•
Cruise control
CRUISE (USA models) / 0 (Canada models)
The CRUISE warning/indicator light illuminates when the cruise
control is activated. •
Airbag system !_J·
This warning/indicator light monitors the airbag and the
tensioner systems.
The ! .!r warning light illuminates for a few seconds each time you
switch on the ignition.
If the
! !r warning light does not go out, or if it illuminates whi le you
are driving, or if it starts to flash, then there is a ma lfunction some ­
where in the system . If the light does not illuminate when you
switch on the ignition, this also means there is a malfunction.
& WARNING
If you ha ve a malfunction in the a irbag sy stem , cont act your autho­
rized Audi dealer immedi ately. Otherwi se the airba g or the belt
ten sioner may not wor k properl y in an acci dent. •
Generator 0
This warning/indicator light detects a malfunction in the
generator or in the vehicle's electrical system .
The O warning/indicator light illuminates when you switch on the
ignition and must go out after the engine has started.
If the
O warning/indicator light il luminates while you are driving,
you shou ld co ntact your authori zed Aud i dealer . Since the veh icle
battery is discharging, you should switch off any unnecessary elec­
trical consumers ( for example, the air conditioner) .•

Driver information display
Service interval display
The service interval display reminds you when your next
service is due.
Fig. 9 Section of
instrument cluster:
Service interval display
The schedule for the next oil change or inspection is calculated
automatically and displayed accordingly. The display works in two
stages:
Service reminder
30 days before the next service is due, a service reminder appears in the display when you turn on the ignition.
After about 5 seconds the display switches back to normal. The distance and time remaining are updated each time the ignition is
turned on until the date due for service is reached.
Service due
When the due date for service is reached, the message Service due
! appears in the instrument cluster immediately after you turn on
the ignition. Additionally, a warning tone sounds. After about 5 seconds the display switches back to normal.
Calling up the service schedules
If or when an oil change or inspection is due, can be shown in the
instrument cluster by selecting the service interval display . Select
Check > Service > Oil change or Service by using the [ RESET! button
and the rocker switch =>
page 23, fig. 13.
Resetting the service interval display
Your authorized Audi dealer will reset the corresponding service
schedule after performing the appropriate service on your vehicle.
You also have the possibility to reset the oil change schedule after
having performed an oil change according to Audi specifications.
• Switch the ignition on.
• Pull the knob @=>
page 8, fig. 2. The message. Service
due!appears .
• Pull the knob until the display
Oil change in----- mi (kml---days
appears in the display . If the reset button is not pulled within 5
seconds, the display reset mode closes .
0 Note
If you disconnect the battery terminals, no calculations can be
made for the service interval display during this time and no service
reminder will appear. Remember that observing the proper service
intervals is vitally important to extending the life of your vehicle,
particularly the engine, and maintaining its value. Even if the
mileage driven is low, the maximum period of one year from one
service to the next must not be exceeded.
[ i] Tips
• Do not reset the display between oil changes, otherwise the
display will be incorrect.
• The information in the Service Reminder remains stored even
when the vehicle battery is disconnected .•

Distance
The elapsed distance since the last time the memory was cleared
appears in the display. The maximum distance that can be recorded
is 9,999 .9 miles (9,999.9 kilometers).
[ i ) Tips
All stored values will be lost if the vehicle battery is disconnected. •
Operation
The trip computer is controlled by two switches on the
windshield wiper lever.
Selecting the trip computer
Fig. 12 Wiper
arm/wiper lever:
co ntr ols for the trip
co mputer
- Tap the [Reset) button © until the tr ip computer
(memory level 1 or 2) appears in the display =>
page 22,
fig. 11.
Selecting the functions
- Push in the upper (lower) protrusion on the functi on
se lector switch @=>fig . 12. The functions for the trip
computer are displayed in succession on the respective
memory levels.
Contro ls and eq uip­
ment
Driver information display
Resetting the function to zero
- Push the
(Reset] button © for at least two seconds.
You can reset the following values to zero using the [Reset] button:
• driving time
• distance
• average fue l mi leage
• average speed
The trip computer only operates when the ignition is on. When you
turn on the ignition, the function that was in use when you last
tu rned the ignition off will be displayed.
[ i ) Tips
• You can also set the values for the functions to zero in the menu
display
( Reset) ~ page 23.
• All stored values will be lost if the vehicle battery is
disconnected .•
Menu display
Introduction
Fig . 13 Wiper lever:
Controls for the menu
di sp la y ..,
Vehicle care I I irechnical data

Yellow symbols
A yellow symbol means WARNING.
Contro ls and eq uip­
ment Low fuel level
Check engine oi l level
Engine oil sensor malfunction
Engine speed limitation
Diesel particulate filter
Worn brake pads
USA models:
Speed warning 1
Canada models:
Speed warning 1
USA models:
Speed warning 2
Canada models:
Speed warning 2
Dynamic headlight range con -
trol * defective
W indshield washer fluid level low
Battery voltage too high or too
low
Defective light bulb
=> page 32
=> page33
-
=> page33
=> page32
=> page32
=> page33
=> page 33
=> page33
=> page33
=> page33
=> page33
=> page33
...
=> page 33
=> page34
-
-
-
Driver information display
USA models: => page34
Defective brake light
Canada models: => page 34
Defective brake light
Light/rain sensor defective (auto-
=> page 34
matic headlights)* defective
-Adaptive Light * defective => page34
Tire pressure monitoring system * => page 35
When a yellow symbol appears, a warning tone will sound once.
Check the displayed function as soon as possible. If more than one
malfunction is d etected, all symbols will appear one after the other
for about two seconds. •
Driver information
In addition to the warning/indicator lights and the
symbols in the instrument cluster display, driver informa­ tion is displayed .
Vehicle care I I
Fig. 21 Section of
instrument cluster:
Set/Check button
irechnical data

If the '-" symbol comes on, add 1 quart (1 liter) of oil at the next
opportunity =>
page 230. •
Checking the engine oil level r.,
When the symbol illuminates, check the engine oil level as soon
as possible=>
page 229. Top off the oil at your earliest opportunity
=>
page 230. •
Engine oil sensor defective -;...
If the symbol illuminates, contact your authorized Audi dealer
and have the oil sensor inspected.•
Worn brake pads ~ :;
rt. Brake pads!
If the warning light illuminates, immediately contact your autho ­
rized Audi dealer or qualified workshop to have all brake pads
inspected. On USA models the warning light? comes on together
with the warning light
BRAKE. Both sets of brake pads on an axle must
always be replaced at the same time.
& WARNING
Driving with bad brakes can cause a collision and serious personal
injury.
• If the warning light and the warning light
BRAKE11 with the
message Brake pads! comes on in the instrument cluster display,
immediately contact your authorized Audi dealer or qualified
workshop to have all brake pads checked or replaced if
necessary. •
11 BRAKE : USA models only
Controls and equip ­
ment
Speed warning
models) 1
· ,I'""'
Driver information display
(USA models> IP (Canada
If the ~ symbol illuminates, this means you are driving faster than
the set vehicle speed. Slow down!=>
page 26. •
Speed warning 2 r (USA models) /,.__, (Canada
models)
If the C) symbol illuminates, this means you have driven faster than
the second set vehicle speed. Slow down! =>
page 26. •
Applies to veh icles : wi th dynamic head light range ad justment
Headlight range control defective
If the illuminates, the dynamic headlight range control is no
longer working properly. Have the system checked and repaired at
your authorized Audi dealer. •
Windshield washer fluid level too low .-_j
If the ~ symbol illuminates, add windshield washer fluid to the
washer system =>
page 240. •
Battery voltage low ~
If the C symbol illuminates, contact your authorized Audi dealer
and have the following components inspected:
• drive belt
• battery charge
Also see if the generator warning/indicator light illuminates
=>
page 14. •
I • •

[ i J Tips
• If you open the driver's door with the key left in the ignition lock,
a chime will sound. This is your reminder to remove the key and lock
the door.
• For security reasons, replacement keys are only available from
authorized Audi dealers. •
Master key with remote control
The remote control allows you to Jock or unlock the
vehicle electronically.
Fig . 23 Fold-up master
key with remote
control
- To fold the key out and back in place, press the release
button
~ fig. 23.
The transmitter and battery are located in the head of the remote
control. The receiver is located inside the vehicle. The maximum
effective range depends on several things. Remember, if the battery
is weak, the effective range decreases.
If you need to replace the remote control, or if you need to have it
repaired, you must see your authorized Audi dealer. Only then can
you use the key again.
Con tro ls and eq uip­
ment
Opening and closing
[ i J Tips
• If the ignition is switched on, the remote control system is deac­
tivated.
• The remote control system can be affected by other systems
operating in the same frequency range close to the vehicle, such as
mobile telephones, television broadcasting stations, etc.
• For Declaration of Compliance to United States FCC and Industry
Canada regulations=> page
302. •
Check light in remote master key
The check light in the remote master key indicates the
state of charge of the battery.
State of master key battery
Fig. 24 Check light in
the master key
When a button is pressed, the check light flashes=> fig. 24 (arrow).
If the check light does not come on or flash, the battery is dead and
has to be replaced.
Battery replacement => page
38. •
Vehicle care I I irechnical data

Opening and closing
Master key battery replacement
Each master key contains a battery housed under the
cover.
Fig . 25 Master key:
opening the cover
We recommend having the battery changed by a qualified
workshop. However, if you wish to replace the dead battery
yourself, proceed as follows:
- Pry apart the base::::::,fig. 25
@andthecover @carefully
with a coin.
- Remove the cover (arrow) .
- Remove the dead battery from the cover.
- Install the new battery. Please make certain that the"+"
sign on the battery faces down. Correct polarity is shown
on the cover.
- Place the cover with the new battery on the key base and
press both parts together.
For the sake of the environment
Dispose of dead batteries properly so as not to pollute the environ ­
ment.
[ i ] Tips
The replacement battery must be the same specification as the
original. •
Electronic immobilizer
The immobilizer prevents your vehicle from being started
by unauthorized persons.
A computer chip inside your key automatically deactivates the elec ­
tronic immobilizer when you insert the key in the ignition lock .
When you remove the key from the ignition lock, the electronic
immobilizer is automatically activated once again .
If an unauthorized key was used,
SAFE is displayed continuously in
the odometer display field.
[ i ] Tips
• Your engine can only be started using the factory -equipped key.
• You may not be abl e to s tart your vehicle if an ignition key of a
different vehicle make is also located on your set of keys.
• For Declaration of Compliance to United States FCC and Industry
Canada regulations ~
page 302. •
Power locking system
General description
The power locking system locks or unlocks all doors and
the rear lid simultaneously.
The power locking system in your vehicle incorporates the following
functions:
• Central locking function