2010 AUDI Q7 service

• Do not attach any st ickers to the w indshield in front of the light
sensor*, as t his wou ld interfere with the au toma tic ope ra tion of the
headlights and the automat ic dimming of the ins ide mirror.
• Be aware that automatic dimming o f the ins ide mir ror can on ly
operate proper ly if the rear w indow sun b lin d* is retracted . •
Outside mirrors
The outside mirrors are electrically adjusted.
Adjusting the outside mirrors
F ig . 7 1 Forward
sec tion of d riv e r's
a rmr est: po wer mirr or
con trols
- Tur n the adjus ting k nob to position (0 ~ fig. 71 to ad just
the outside mi rror on the driver's sid e.
- Turn the adjusting knob to position ® to adjust the
outside mirror on the passenger side .
- Press the knob in the appropriate direction to move the
mirror surface so that you have a good view to the rear .
Heated mirrors
-Turn the knob to position @.
Folding both outside mirrors flat*
-Turn the knob to@ .
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
Depend ing on the outs ide temperature, the mirror surfaces are
heated until t he ignit ion is sw itched off -eve n if the knob is no longe r
in pos ition
@ .
You are well-advised to fold the o utside mirrors in when maneuver ing
in tight spaces or w hen leaving the ca r pa rked close to othe r veh icles .
Memor y setting for the out side mirrors*
When the seat position is saved in the memory, the posit ion of the
outside mirrors is saved at the same time~
page 87.
If the pos it io n of t he passe nger m irror is changed when the vehicle is
in reverse gear and the switch is in the ® position, this new tilted
posit ion w ill be a utoma tica lly saved to the remote key when the
vehicle is taken out of reverse gear . To save, the rotary knob for mirror
adjus tment mus t be in the ® position, the se lec to r l ever must be in
the P position and the ignition must be off . T hi s will now become the
stored setti ng when the vehicle is put in reve rse gear agai n.
Tilting the passenger 's side outside mirror (only
with seat memory)
Whe n you move the selector lever into
R (Reverse), the mir ror o n the
front passenger 's doo r (knob tur ned to® ~ fig . 71) will tilt s light ly
dow nward. This make is eas ier for you to see the curb when you are
backing into a parking space.
Th e m irro r returns to its in it ial posi tion as soon as rever se gear is
disengaged and veh icle speed is above about 9 mph (15 km/h) . T he
mirror also returns to i ts initia l position i f the swit ch is moved to the
dr iver 's outs ide mirror © or the ign it ion is switched off .
Automatic anti-glare for the out side mirror s*
The outside mirrors dim at the same time as the inside m irror. When
t he ign ition is sw itched on, the mir rors automatic ally dim depending
on the amount of light str ik ing the m irrors (such as headlights
shining into the veh icle from t he rear) .
When you t urn on the interio r light, or when you move the selector
lever into R (Reve rse), the anti -glare f unction stops and the mirrors
return to their orig inal condition (not darkened) . -.,
Vehicle care Do-it-yourselt service iTechnical data

Digital compass
Applies to veh icles: wit h digita l co mp ass
Activating or deactivating the compass
The direction is displayed on the interior rear view mirror.
Fig. 72 Inside rear
view mirror: digital
compass activated
To activate or deactivate, hold the@ button down until
the red display appears or disappears .
The digital compass only works with the ignition turned on. The direc­
tions are displayed as initials:
N (North), NE (Northeast), E (East), SE
(Southeast), S (South) , SW (Southwest), W (West), NW (Northwest).
(I) Tips
To avoid inaccurate directions, do not allow any remote controls ,
electr ical systems, or metal parts close to the mirr or.•
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
Applies to veh icles : w ith d ig ita l compass
Setting the magnetic deflection zone
The correct magnetic deflection zone must be set in order
to display the directions correctly .
.
,_ ,;=.~a,, I I
I I
I I
I ' I I
I I
1 ! ©
l 4
l
l
I ' I ,,
l ----
'
'
'
®
\, ,, ...... _______ ,.,.
©
@
Fig. 73 North America: magnetic deflection zone boundaries
-Hold the@=> fig . 72 button down until the number of
the set magnetic deflection zone appears on the interior rear view mirror .
- Adjust the magnetic deflection zone by repeatedly pressing on the@ button . The set mode automatically
deactivates after a few seconds. •
Vehicle care Do-it-yourselt service iTechnical data

Seat memory
Applies to veh icles: with seat memory
Driver's seat memory
The seat adjustment settings for two drivers can be
stored using the memory buttons in the driver's door.
Fig . 76 Driver's door:
Seat memory
In addition to the setting for the driver's seat, the settings for the
steering column* and both exterior mirrors can be stored.
Storing and re calli ng setting s
Using the memory buttons 1 and 2, you can store and recall the
settings for two different drivers => fig . 76 .
T he current settings are also automatically stored on the remote
control key being used when the vehicle is locked. When the vehicle is
unlocked, the settings stored on the remote contro l key being used
a re automatically recalled. This function has to be activated in the
MMI
=> page 88, "Activat ing remote control key memory ".
T urning se at m em ory on and off
If the [ ON/OFF] switch is depressed , the seat memory is inoperative .
The word
OFF next to the [ ON/OFF] switch illuminates.
All the stored settings are retained. We recommend using the
[ ON/OFF ] switch and deact ivat ing the seat memory if the vehicle is
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Seats and storage
only going to be used temporarily by a driver whose settings are not
going to be stored .•
App lies to vehi cles : w it h seat memo ry
Storing and recalling a seat position
Before you can store or recall your seat position, the
(ON/OFF) button must be engaged (down) .
Storing settings
-Adjust the driver 's seat => page 84.
- Adjust the steering column*=> page 123.
Adjust both outside mirrors=> page 79. In the tilt -down
position, the passenger mirror can be adjusted to the
preferred position and saved in the seat memory.
- Press the
(SET) button and hold it down. At the same
time, press one of the memory buttons for at least one second.
- Release the buttons. The settings are now stored under
the corresponding memory button.
Rec alling settings
- Driver's door open -press the desired memory button.
- Driver's door closed -press the corresponding memory
button until the stored position is reached .
Successful storage is confirmed audib ly and by the light in the [ SET]
button illuminating.
When the vehicle is
loc ked , the current settings are stored and
assigned to the remote control key. But the settings stored on
memory buttons 1 and 2 are not deleted. They can be recalled at any
~
Vehicle care Do-it-yourselt service iTechnical data

....
~....-'""-~_3-:>--.....,__~~ :
······--... __ ;::::.:_ :::--~
Adjusting seat back angle
Fig . 78 Fore -and -af t
adju stme nt
- Pull the lever up an d push the seat bac k toward t he rear to
t h e desi red position ==>
page 88, fig. 77. Release the lever.
- Pull t he lever up so that the seat back pivots forward.
Release t he lever and pus h the seat back to the rear to
retu rn t he sea t bac k to the norma l position.
Fore-and-aft adjustment*
- Pull t he ha ndle up and push the seat forward or back
==> fig. 78.
- Releas e the handle a nd cont inue to p ush th e seat u ntil the
sea t latc h engages.
& WARNING
• For safety rea son s, the seat mu st only be adjusted when the
vehicle is stationary · danger of accident!
• Exerci se caution when adjusting the seat . Adju sting the seat
without checking or paying attention c an pinch finge rs or limbs·
danger of injury! •
Con trol s and equ ip­
m ent Vehicle
OP-eration
Seats and storage
Applies to ve hicles : with e ntry assist
Entry assist (second row seating)
The entry assist makes it easier for occupants to reach
the third row seating*.
Fig. 79 Seat back
s e co nd r ow sea ting :
S eat back lat ch
Pushing second row of seats forward
- Lift the lever==> fig . 79.
- Tilt the s eatback forwa rd .
- Pu sh the seat forward.
Pushing second row of seats back
-Push the seat back.
- Fo ld the seat back u p un til it latches.
T o make en try to and ex it from the rear of the vehi cle eas ie r, the seat
backs for th e se cond row seating can be folded fo rwa rd. At the sam e
time, the seats ca n be pushed forwa rd and to the rear. •
Vehicle care Do-it-yourselt service iTechnical data

The head restraints on the front seats can be adjusted to
provide safe support to head and neck at the optimum
height. When optimally adjusted, the top of the restraint
should be level with the top of the head~
page 193, "Proper
adjustment of head restraints".
Raising head restraint
- Grasp the side of the head restraint with both hands.
- Adjust the head restraints so that the top of the head
restraint is
at least level with your eyes or higher
~ page 90, fig. 82.
Lowering head restraint
-Grasp the sides of the head restraint with both hands.
Press the button~
page 90, fig. 82 and adjust the head
restraint.
- Adjust the head restraints so that the top of the head
restraint is
at least level with your eyes or higher
~ page 90, fig. 82.
Refer to::::;, page 193, ''Proper adjustment of head restraints" for
guidelines on how to adjust the height of the front head restraints to
suit the occupant's body size.
& WARNING
• Driving without head restraints or with head restraints that are
not properly adjusted increases the risk of serious or fatal neck
injury dramatically.
• Read and heed all WARNINGS:::::>
page 193.
Contro ls a nd e quip ­
m en t Vehicle
OP-eration
Seats and storage
(I) Tips
Correctly adjusted head restraints and safety belts are an extremely
effective combination of safety features.•
Outer rear head restraints
Passengers may only be carried in the outer rear seats
when the head restraint is raised.
Fig . 83 Outer rear
seats: Head restraint
If the outer rear seat is not occupied, you can lower the head
restraint to obtain better vision to the rear.
- Pull on the loop to fold the head restraint down~ fig. 83.
- Push the head restraint up again until it latches with an
audible click.
& WARNING
• The head restraints for the outer seats in the second row must
be folded up when persons are being carried in the third row
seating*· danger of injury!
• Read and heed all WARNINGS:::::>
page 193 •
Vehicle care Do-it-yourselt service iTechnical data

& WARNING (cont inued )
an accident, sudden braking or other vehicle movement , hot liquid
c ould spill, cau sing scalding burn s. Spilled hot liquid can also
cause an accident and personal injury .
• Use only soft cups in the cupholder. Hard cups and glasses can
cause inju ry in an accident.
0 Note
Only drink conta iners with lids should be carr ied in the c upholder.
L iquid could spill ou t a nd d amage your vehicle 's e lec tron ic eq uipment
or sta in the upho lstery, etc. •
Applie s to veh icle s: w ith lo ng cent er conso le
Long center console
Fig. 86 Long rea r
ce nte r con sole
There are two cupholders an d a storage bin i n the long rear
cen ter conso le. The ar mrest is also height a djustable.
Beverage holder
- Tap the cover==> fig. 8 6 -Arrow- for it to open a utom ati­
cally .
Contro ls a nd e quip ­
m en t Vehicle
OP-eration
Seats and storage
-Push the cover down to clo se th e b in.
Storage compartment
- Lift the cover by t he front to open the com partment .
- Push the cover down to close the bin .
Adjusting the armrest
-Press t he re lease but ton. The armrest moves u p au toma t­
ica lly .
- Release the b utto n w hen t he desi re d heigh t is reac hed .
- Press the re lease butto n aga in and at t he sa me tim e push
the armrest down to lower it .
& WARNING
Spilled hot liquid can cause an accident and personal injury.
• Never carry any beverage containers with hot liquids, such as
hot coffee or hot tea, in the vehicle while it is moving . In case of
an accident, sudden braking or other vehicle movement, hot liquid
could spill, causing scalding burn s. Spilled hot liquid can al so
cause an accident and personal injury.
• Use only soft cups in the cupholder . H ard cups and glasses can
cause injury in an accident .
0 Note
Only drink conta iners with l ids should be ca rr ied in t he c upholder .
L iq uid could spill out and damage your vehicle 's e le ctron ic equipment
or sta in the upholstery, etc. •
Vehicle care Do-it-yourselt service iTechnical data

& WARNING (cont inued )
damage to webbing, bindings , buckles, or retractors must be
replaced.
& WARNING
Always read and heed WARNINGS=> & in "Loading the luggage
compartment " on
page 195.
0 Note
• When fo lding the backrest back i nto place, ma ke sure the safety
bel t does no t ge t ca ugh t, b ec ause i t can be damaged .
A damaged bel t
can fail to provide safe rest raint.
• Th e heating wires in th e rear w indow ca n be damaged by abrasive
objects on t he parcel s he lf . •
Tie-down rings
Th er e a re f our tie-d own rings in the lu ggage com part­
m en t for s ecuring lugg age items.
Fig . 89 Loca tion of
the tie-down rings in
the lug gag e c ompa rt ·
ment
- Sec ure the c argo to the tie-dow n rings => fig. 89 .
- Observe the safety notes=:> p age 19 7.
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Seats and storage
In a co llision, the laws of physics mean that eve n smaller items that
a re lo ose in the vehicle w ill turn in to heavy mis siles th at can c ause
ser ious injury. Items in the vehicle pick up kinet ic en ergy w hich varies
with the ve hicle an d th e we ight of the item. Vehi cle speed is the most
signif ica nt factor .
For example, in a frontal collis ion at a speed of 30 mph (48 km/ h),
t he force s acti ng on a 10- lb
(4 .5 kg) object a re a bout 20 times the
normal weight of t he item. T his means that t he weight of t he item
wou ld su ddenly be t he e quiva le nt of abou t 200 lbs (9 0 k g). One can
easily imagine the injur ies that an item of that weight flying freely
t hroug h the passenger com par tment can cause in a collis ion at a
speed considered relative ly low .
& WARNING
Weak , damaged or improper straps used to secure items to tie­
downs can fail during hard braking or in a collision and cause
serious personal injury.
• Always use suitable r etaining straps and properly secure items
to the tie -downs
in the luggage compartment to help prevent
items from shifting or flying forward .
• When the rear seat backrest is folded down, always use suit·
able retaining straps and properly secure items to the tie-downs in
the luggage compartment to help prevent items from flying
forward into the passenger compartment.
• Never attach a child safety seat tether strap to a tie-down .•
Vehicle care Do-it-yourselt service iTechnical data

-Hook t he ends of the rod in t he openings in the left and
r ight side trim panels==>
page 96, fig. 9 1 @ .
Rolling up front Luggage compartment cover
- Pull the ends of the cover out of the attachi ng eyes in the
seat back.
- Allow the cover to ro ll up slow ly.
Rolling up rear Luggage compartment cover
- Pull t he rod out o f the op enings in t he side trim panels.
- Allow the cover to ro ll up slow ly.
Removing the Luggage compartment cover
- Pull t he lever in the direc tion of the arrow==> page 96,
fig. 92 and at the same time lift the cover up and out .
Installing the Luggage compartment cover
-Lay the cov er i n the left retaine r in the side trim and then
press it in to the right re tainer until it la tches.
& WARNING
Whenever driving, nev er place any hard or he avy objects on the
luggage compartment or allow pets to sit on the luggage
compa rtment cover . They could become a hazard to v ehicle occu­
pants in the e vent of sudden b raking o r in an accident.
0 Note
• Make sure that the heating wires in the rear lid do not get
damaged by objects scraping agai nst them .
• The two inner attach ing eyes on the left and right in the seatback
=> page 96, fig. 9 1 (D are not suitable for tying down cargo - r isk of
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Seats and storage
damage . Only the luggage compartment cover should be attached
here.
[ i ] Tips
• You can use the luggage compartment cover to sto re light we ight
clothi ng or articles but do not leave any heavy o r sharp objects in the
pockets of the clothing.
• Remember that plac ing clothing or articles on the luggage
compartment cover can block the driver's vision i n the rea r view
m irror. This also applies especially when you have to transport large
objects.
• So that stale a ir can escape from the vehicle be sure not to cover
the vent ilation slot between the rear lid a nd the luggage compa rt­
ment cover .•
Protective liner
D ir ty or wet objects can be transported under the cargo
floor in a protective tray .
Fig. 93 C argo floor :
fo lde d upr ight ~
Vehicle care Do-it-yourselt service iTechnical data