2010 ASTON MARTIN V8 VANTAGE wheel bolt torque

Clutch Assembly (08.01)
May 2007 Workshop Manual 8-1-3
8. Remove bolts (x8) from flywheel to crankshaft and discard bolts (see Fig. 3).
9. Remove bolts (x2) and collect special tool SKAM14546 OTC.
10. Release flywheel from dowels and remove flywheel.
Installation
1. Clean flywheel and mating face on crankshaft flange.
2. Inspect pilot bearing for wear.
3. Position flywheel and align to dowel(s) on crankshaft flange.
4. Install bolts (x8) and install special tool SKAM14546 OTC to restrain flywheel.
5. Tighten flywheel bolts in the correct sequence.
6. Clean clutch cover and drive plate.
7. Install clutch assembly on flywheel and align to dowels.
8. Install bolts (x8), insert clutch alignment tool and evenly tighten bolts to the correct torque.
9. Remove clutch alignment tool.
10. Remove bolts (x2) and collect tool.
11. Install inspection cover to crankcase and tighten bolts (x2).
12. Install torque tube assembly (see Workshop Manual procedure 05.01.CA Torque Tube Remove for Access
and Refit).
13. Lower vehicle on ramp.
14. Connect vehicle battery.
Slave Clutch Cylinder-Renew
08.00.AC
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove torque tube (see Workshop Manual procedure 05.01.CA Torque Tube Remove for Access and Refit).
4. Release clips and remove bleed and supply pipes from slave cylinder.
5. Install clips in union
6. Loosen and remove pipe adaptors (x2) from slave cylinder (see Fig. 1).
7. Sportshift Only - Remove bolts (x2) securing clutch
position sensor to slave cylinder.
Fig. 3
Warning
The flywheel is heavy. Ensure the flywheel is supported
before removing.
Warning
The flywheel is heavy. Ensure the flywheel is supported
when installing.
Warning
The clutch assembly is heavy. Ensure the clutch
assembly is supporte d when installing.
Caution
The flywheel and pressure are a balanced assembly. Ensure alignment marks are aligned.

Repair Operation Time (ROT)
Warning
Always disconnect the battery earth (- ve) terminal first.
Warning
When raising the vehicle on a ‘two post’ ramp, ensure
that the rear end of the vehicle is securely strapped to
the ramp. Failure to strap the rear of the vehicle down may lead to the vehicl e falling off the ramp.
Caution
Always plug pipe ends to prevent ingress of dirt or moisture into the system.
Fig. 1


Silencer Assembly (09.01)
Exhaust (09.00)9-1-4 Workshop Manual Issue 5, January 2010
Removal
1. Raise vehicle on ramp.
2. Remove rear exhaust silencer (refer to Workshop Manual procedure 09.00.KA Muffler & Bypass Valve
Assembly - Remove for Access & Refit).
3. Disconnect multiplugs (x2), HEGO sensors.
4. Release sensor lead from clip on heatshield.
5. Secure sufficient lengths of string to HEGO sensor multiplugs for assembly purposes.
6. Loosen LH and RH clamp nuts , catalysts to centre pipe.
7. With assistance, manoeuvre exhaust centre pipe assembly rearwards to release from catalysts.
8. Remove nuts (x3), catalyst to exhaust manifold.
9. With assistance, release and support weight of RH catalyst from exhaust manifold.
10. Manoeuvre HEGO sensor leads and remove cable tie. Release HEGO sensor leads from behind heat shield.
Remove string from HEGO multiplugs.
11. Remove catalyst assembly.
12. Remove and discard gasket.
13. Remove HEGO sensors (x2) from catalyst.
Installation
1. Clean catalyst, mating joint faces and HEGO sensors..
2. Install and tighten HEGO sensors (x2) to catalyst.
3. Apply proprietary exhaust sealant around pipe joints.
4. Install new gasket to exhaust manifold flange.
5. With assistance, position catal yst, secure string (x2) to
HEGO multiplugs, feed sensor leads behind heat shield.
Secue cable tie. Install catalyst to exhaust manifold.
6. Install and torque tighten nuts (x3), catalyst to exhaust manifold.
7. Align centre pipe asembly to catalyst, torque tighten
clamp nuts.
8. Remove string (x2), connect multiplugs (x2), HEGO sensors.
9. Secure sensor lead in clip on heatshield.
10. Install rear exhaus t silencer (refer to Workshop Manual
procedure 09.00.KA Muffler & Bypass Valve Assembly -
Remove for Access & Refit).
11. Lower vehicle on ramp.
LH Exhaust Manifold-Renew-Roadster
Only
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp. 3. Remove heatshield deflec
tor, front floor (refer to
Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
4. Remove LH front wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
5. Remove nuts (x8), securing manifold to cylinder head.
6. Remove exhaust manifold, remove and discard gasket.
Installation
1. Clean manifold and mating face on engine. Install new gasket to engine.
2. Install manfold to engine.
3. Install nuts (x8) securing manifold to cylinder head
(torque).
4. Install LH front wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
5. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
6. Lower vehicle on ramp.
7. Connect vehicle battery.
Heated Exhaust Gas Oxygen (HEGO)
Sensor - Remove and Install
Removal
1. Raise the vehicle and make it safe.
2. Release the two electrical connnectors for the Heated Exhaust Gas Oxygen (HEGO) sensor from the bracket.
3. Disconnect the two electrical connnectors from the HEGO sensor.
4. Move the two wiring harnesses for the HEGO sensor away.
5. Remove the two bolts that attach the bracket to the engine.
6. Remove the bracket.
7. Remove the two bolts that attach the heat shield to the torque tube.
8. Move the heat shield away.
Repair Operation Time (ROT)
Repair Operation Time (ROT)
ItemCode
Heated Exhaust Gas Oxygen (HEGO)
Sensor - Remove and Install 09.00.DB
WAR NI NG
THE EXHAUST SYSTEM WILL BE VERY HOT AFTER
OPERATION. LET THE EXHA UST COOL BEFORE YOU
DO WORK. IF YOU DO NO T, PESONAL INJURY CAN
OCCUR.

Silencer Assembly (09.01)
Exhaust (09.00)9-1-6 Workshop Manual Issue 5, January 2010
2. Clean silencer and mating faces on rear pipes.
3. Remove Rear RH wheel arch liner (refer to Workshop Manual procedure 01.02.HB Wheel Arch Liner - Rear -
RH - Renew).
4. Remove rear undertray (refer to Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
5. Apply a proprietary exhaust sealant around all clamp joints
6. Remove Allen bolts (x2), loosen Allen bolts (x2), bumper diffuser to mounting brackets and remove diffuser.
7. Position silencer on lifter.
8. Install silencer, position rear hangers to body, install and torque tighten bolts (x4).
9. Remove Rear LH wheel arch liner.
10. Disconnect both by-pass valve vacuum lines.
11. Remove Allen bolts (x2), loosen Allen bolts (x2), bumper diffuser to mounting brackets and Remove diffuser.
12. Position front mountings to subframe, install and torque tighten bolts (x4).
13. Loosen clamp nuts (x2), remove stub pipes (x2).
14. Disconnect both by-pass valve vacuum lines.
15. Align silencer to rear pipes, install springs onto bolts (x4), install and torque tighten bolts (x4).
16. Remove bolts (x4), rear exha ust pipes to silencer. Collect
springs from bolts.
17. Loosen clamp nuts (x2), remove stub pipes (x2).
18. Install stub pipes (x2), centralise stub pipes to exhaust trim finisher. Torque ti ghten clamp nuts (x2).
19. Remove bolts (x4), securing LH and RH silencer rear
hanger brackets to body.
20. Remove bolts (x4), rear exhaust pipes to silencer and collect springs from bolts.
21. Check silencer to rear pipes for correct alignment and clearances.
22. Remove bolts (x4), silencer front mountings to subframe.
23. Remove bolts (x4), securing LH and RH silencer rear
hanger brackets to body.
24. Connect lines to both by-pass vacuum valves.
25. Position suitable lifter to support weight of silencer.
With assistance, remove silencer.
26. Remove bolts (x4), silencer front mountings to subframe.
27. Install rear bumper diffuser and install and tighten Allen
bolts (x4).
28. Install Rear RH wheel arch liner (refer to Workshop Manual procedure 01.02.HB Wheel Arch Liner - Rear -
RH - Renew).
Installation
1. Position suitable lifter to su pport weight of silencer. With
assistance, remove silencer.
2. Clean silencer and mating faces on rear pipes.
3. Install Rear LH wheel arch liner.
4. Apply a proprietary exhaust sealant around all clamp joints 5. Lower vehicle on ramp.
6. Position silencer on lifter. Install silencer, position rear
hangers to body, install and torque tighten bolts (x4).
7. Position front mountings to subframe, install and torque tighten bolts (x4).
8. Align silencer to rear pipes, install springs onto bolts (x4), install and torque tighten bolts (x4).
9. Install stub pipes (x2), centralise stub pipes to exhaust trim finisher and torque tighten clamp nuts (x2).
10. Check silencer to rear pipes for correct alignment and clearances.
11. Connect lines to both by-pass vacuum valves.
12. Install rear bumper diffuser and install and tighten Allen bolts (x4).
13. Install rear undertray (r efer to Workshop Manual
procedure 01.02.PB Undertray - Rear - Renew).
14. Lower vehicle on ramp.
Silencer and Bypass Valve Assembly-
Renew
Removal
1. Raise vehicle on ramp.
2. Coupe Only - Remove rear undertray (refer to
Workshop Manual procedure 01.02.PB Undertray -
Rear - Renew).
3. Roadster Only - Remove RH rear wheel arch liner (refer
to Workshop Manual procedure 01.02.HB Wheel Arch
Liner - Rear - RH - Renew).
4. Roadster Only - Remove LH rear wheel arch liner.
5. Remove Allen bolts (x2, loosen Allen bolts (x2), securing bumper diffuser to mounting brackets. Remove diffuser.
6. Disconnect both by-pass valve vacuum lines.
7. Loosen clamp nuts (x2), remove stub pipes (x2).
8. Remove bolts (x4), rear exha ust pipes to silencer. Collect
springs from bolts.
9. Remove bolts (x4), securing LH and RH silencer rear
hanger brackets to body.
10. Remove bolts (x4), muffler front mountings to subframe. Remove mountings from silencer.
Repair Operation Time (ROT)
ItemCode
Silencer and Bypass Valve Assembly-
Renew 09.00.KB
WAR NI NG
THE EXHAUST SYSTEM WILL BE VERY HOT AFTER
OPERATION. LET THE EXHA UST COOL BEFORE YOU
DO WORK. IF YOU DO NO T, PESONAL INJURY CAN
OCCUR.
WAR NI NG
GET THE AID OF ONE MORE PERSON WHEN YOU
REMOVE THE REAR EXHAUST SILENCER.
THE SILENCER IS HEAVY .

Silencer Assembly (09.01)
Exhaust (09.00)
Issue 5, January 2010 Workshop Manual 9-1-7
11. Position suitable lifter to support weight of silencer.
With assistance, remove silencer.
12. Remove both rear rubber mountings and hanger brackets from silencer.
Installation
1. Clean silencer and mating faces on rear pipes and stub pipes.
2. Install both rear rubber mountings and hanger brackets to silencer.
3. Position silencer on lifter . Install silencer, position
hangers, install and tighten bolts (x4).
4. Install front mountings to silencer, install and tighten bolts (x4).
5. Align silencer to rear pipes. Install springs (x4), and torque tighten bolts (x4).
6. Install and align stub pipes (x2) to silencer and trims in bumper. Align and tighten clamp bolts.
7. Check silencer to rear pipes for correct alignment and clearances.
8. Install stub pipes (x2), insta ll clamps (x2), centralise stub
pipes to exhaust trim finisher, torque tighten clamp nuts
(x2).
9. Check silencer to rear pipes for correct alignment and clearances.
10. Connect lines to both by-pass vacuum valves.
11. Install rear bumper diffuse r. Install and tighten Allen
bolts (x4).
12. Roadster Only - Install RH rear wheel arch liner (refer to
Workshop Manual procedure 01.02.HB Wheel Arch
Liner - Rear - RH - Renew).
13. Roadster Only - Install LH rear wheel arch liner.
14. Coupe Only - Install rear undertray (refer to Workshop
Manual procedure 01.02.PB Undertray - Rear - Renew).
15. Lower vehicle on ramp.
Exhaust Rear Silencer Mounting Rubber-
Renew
Removal
1. Raise vehicle on ramp. 2. Remove Allen bolts (x4), bumper diffuser to mounting
brackets. Remove diffuser, collect mounting brackets.
3. Remove bolts (x2), securing silencer rear hanger brackets to body.
4. Release/remove rubber mounting and hanger bracket from silencer bracket.
5. Remove rubber mounting from hanger bracket.
Installation
1. To aid assembly, apply liquid soap to rubber mounting .
2. Install rubber mounting on hanger bracket.
3. Install rubber mounting on muffler bracket.
4. Align hanger bracket to body, install and torque tighten bolts (x2).
5. Position mounting brackets, install bumper diffuser, install and torque tighten Allen bolts (x4).
6. Lower vehicle on ramp.
Exhaust System-Renew
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove RH exhaust manifold.
4. Remove RH front wheel arch liner (refer to Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
5. Remove LH front wheel arch liner (refer to Workshop
Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
6. Remove heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
7. Loosen EGR pipe in valve.
8. Remove (nuts x2) EGR pipe from manifold, discard
gasket and tie aside.
WA R N I N G
GET THE AID OF ONE MORE PERSON WHEN YOU INSTALL THE REAR EXHAUST SILENCER.
THE SILENCER IS HEAVY .
Ensure correct alignment of exhaust pipes and silencer before tightening of fixing clamps.
Repair Operation Time (ROT)
WA R N I N G
THE EXHAUST SYSTEM WILL BE VERY HOT AFTER
OPERATION. LET THE EXHAUST COOL BEFORE YOU DO WORK. IF YOU DO NO T, PESONAL INJURY CAN
OCCUR.
Repair Operation Time (ROT)

Silencer Assembly (09.01)
Exhaust (09.00)9-1-8 Workshop Manual Issue 5, January 2010
9. Remove nut (x8) securing RH exhaust manifold to cylinder head (refer to Fig. 1).
10. Remove nut (x2) on RH engine mounting.
11. Raise engine by approximately 25mm.
12. Remove RH exhaust manifold from vehicle and discard
gasket.
13. Remove heatshield from manifold (bolts x4)
14. Remove nuts (x8) securing LH exhaust manifold to
cylinder head.
15. Remove exhaust manifold, remove and discard gasket.
Installation
1. Clean LH exhaust manifold and mating face on cylinder head. Install new manifold gasket.
2. Install LH exhaust manifold to cylinder head.
3. Install and torque tighten nuts (x8) securing exhaust manifold to cylinder head.
4. Clean exhaust manifold and mating face on engine. Install new gasket to engine.
5. Install heatshield to manifold (bolts x4)
6. Install RH exhaust mani fold to cylinder head.
7. Install nut (x8) securing manifold to cylinder head
(torque).
8. Lower engine.
9. Install nuts (x2) on engine mounts (torque).
10. Install (nuts x2) EGR pipe from manifold, clean mating face and fit new gasket (torque).
11. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
12. Tighten EGR pipe in valve (torque).
13. Install RH front wheel arch liner (refer to Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew
14. Install LH wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front - LH -
Renew).
15. Lower vehicle on ramp. 16. Connect vehicle battery.
Exhaust System (Excluding Manifold/
Downpipes)-Renew
Removal
1. Raise vehicle on ramp.
2. Remove undertrays - vehicle set (refer to Workshop
Manual procedure 01.02.PD Undertrays - Vehicle Set -
Renew).
3. Remove Allen bolts(x4), bumper diffuser to mounting brackets. Remove diffuser
4. Disconnect both by-pass valve vacuum lines.
5. Remove bolts (x4), securing LH and RH silencer rear
hanger brackets to body. Remove hanger brackets.
6. Remove bolts (x4), rear exha ust pipes to silencer. Collect
springs from bolts
7. Remove bolts (x4), silencer front mountings to subframe. Remove mountings from silencer.
8. Position suitable lifter to support weight of silencer. with assistance, remove silencer.
9. Mark rear stub pipes to si lencer for assembly purposes.
10. Loosen clamps (x2), rear stub pipes to silencer. Remove stub pipes and clamps.
11. Remove bolts (x4), remove rear subframe cross brace.
12. Loosen clamps (x2), release RH and LH rear pipes from centre pipe.
13. Remove rear pipes through subframe.
14. Loosen clamps (x2), centre pipe to LH and RH catalysts.
15. Coupe Only - Release centre pipe from mountings, LH
and RH catalysts, remove centre pipe.
16. Roadster Only - Remove centre exhaust mounting bolts
(x4).
17. Release LH and RH catal ysts, remove centre pipe.
18. Disconnect multiplugs (x4), from each catalyst.
19. Coupe Only - Secure sufficient lengths of string to
HEGO sensor multiplugs for assembly purposes.
Figure 1
A090069
Repair Operation Time (ROT)
ItemCode
Exhaust System (Excluding Manifold/
Downpipes)-Renew 09.00.NB
WAR NI NG
TO AVOID PERSONAL INJURY, I.E. SEVERE BURNS TO
THE SKIN, ALLOW EXHAUS T SYSTEM TO COOL
DOWN BEFORE REMOVING EXHAUST SYSTEM COMPONENTS.
WAR NI NG
GET THE AID OF ONE MORE PERSON WHEN YOU
REMOVE THE REAR EXHAUST SILENCER.
THE SILENCER IS HEAVY .
Attach lengths of string to th e HEGO sensor multiplugs. This
enables routing the HEGO sensor harness behind the exhaust heat shield on assembly.

Pipes and Supports (09.03)
Exhaust System (09.00)9-2-2 Workshop Manual May 2007
5. Install centre pipe to both catalysts and centre mountings. Do not torque clamp nuts at this stage.
6. Install pipe assembly exha ust rear - LH (refer to
Workshop Manual procedure 09.00.JB Pipe Assembly -
Exhaust - Rear - LH - Renew).
7. Install pipe assembly exhaust rear - RH (refer to Workshop Manual procedure 09.00.HB Pipe Assembly
- Exhaust - Rear - RH - Renew).
8. Align and torque tighten exhaust system nuts/bolts.
9. Lower vehicle on ramp.
RH Exhaust Manifold-Renew
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove RH front wheel arch liner (refer to Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
4. Loosen EGR pipe in valve.
5. Remove heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
6. Remove (nuts x2) EGR pipe from manifold, discard
gasket and tie aside.
7. Remove nut (x8) securing manifold to cylinder head
(refer to Fig. 1).
8. Remove nut (x2) on engine mountings.
9. Raise engine by approximately 25mm. 10. Remove exhaust manifold from vehicle and discard
gasket.
11. Remove heatshield from manifold (bolts x4)
Installation
1. Clean exhaust manifold and mating face on engine. Install new gasket to engine.
2. Install heatshield to manifold (bolts x4)
3. Install manifold to engine.
4. Install nut (x8) securing manifold to cylinder head.
5. Lower engine.
6. Install nuts (x2) on engine mounts.
7. Install (nuts x2) EGR pipe from manifold, clean mating face and fit new gasket (torque).
8. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
9. Tighten EGR pipe in valve (torque).
10. Install RH front wheel arch liner (refer to Workshop
Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
11. Lower vehicle on ramp.
12. Connect vehicle battery.
LH Exhaust Manifold-Renew
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove heatshield deflec tor, front floor (refer to
Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
4. Remove LH front wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
Repair Operation Time (ROT)
A090069
Repair Operation Time (ROT)
ItemCode
Exhaust Manifold-Renew LH09.00.CB
WAR NI NG
TO AVOID PERSONAL INJURY, I.E. SEVERE BURNS TO
THE SKIN, ALLOW EXHAUS T SYSTEM TO COOL
DOWN BEFORE REMOVING EXHAUST SYSTEM COMPONENTS.

Steering Gear (11.01)
Steering (11.00)11-1-4 Workshop Manual Issue 5, January 2010
Specifications
Excessive steering
efforts required to
turn corners and
during parking
manoeuvres Dirty fluid filter.
Low power steering pump fluid.
Clean/replace reservoir.
Fill as required. Check for system leaks.
Damaged accessory drive belt tensioner. New accessory drive belt tensioner.
Hose or oil cooler external leak. New hose or oil cooler as required.
Hose or cooler line restriction. New hose as required.
Fluid aeration.
Damaged pump. Bleed system.
Replace pump.
Fluid leakage Overfilled system. Correct fluid level.
Component leak. Locate suspect component and repair as required.
Accessory drive belt
squeal Check accessory drive belt for correct tension
or glazing .
New accessory drive belt.
‘Chirp’ noise from
steering pump Loose or worn accessory drive belt. New accessory drive belt.
Power steering
pump noisy Low fluid level. Top up and check for system leaks.
Power steering pump.
Steering hoses fouling body structure. Check for leaks. Repair
as required. New pump.
Ensure hose is secured and routed correctly.
‘Hiss’ noise Fluid flow through steering gear rotary valve -
close to ‘Full Lock’. Normal noise.
‘Whine’ noise Aerated fluid. Bleed system.
Steering wheel
vibration Road wheels out of balance. Check front end alignment.
SymptomPossible CauseAction
Torque Figures
DescriptionNm.lb/ft
Ball Joint (M14 nut) 70 52
Track-Rod (lock nut) 70 52
Steering Rack to Subframe (M12) 115 85
Steering Rack Pipe Attachment Plate 9-12 7-9
Intermediate Shaft Pinch Bolt 21-29 15.5-21.5

Power Steering (11.02)
Steering (11.00)11-2-2 Workshop Manual Issue 5, January 2010
Maintenance
Power Steering System - Bleed
Procedure
1. Do a check of the fluid level in the PAS fluid reservoir. Add fluid if necessary.
2. Start the engine and let it idle for 20 seconds.
3. Operate the steering fully to the left and then the right through three cycles.
4. Stop the engine.
5. Wait for five minutes then do a check of the fluid level in the PAS fluid reservoir again.
6. Add fluid if necessary.
7. Install the PAS fluid reservoir cap.
Power Steering Pump-Renew
Removal
1. Remove A/C compressor (see Workshop Manual procedure 03.05.BE Compre ssor - Air Conditioning -
Renew).
2. Coolant drain (see Workshop Manual procedure 03.03.AD Coolant - Drain & Refill).
3. Remove PAS fluid from reservoir.
4. Disconnect HP union from PAS pump pipe.
5. Remove bolt P-clip suction hose to body.
6. Remove bolt (x1) HP pump pipe to engine.
7. Remove bolts (x3) PAS pump to engine.
8. Disconnect bottom hose and move aside.
9. Unclip (x1) harness from cylinder head for access.
10. Manouvre pump forward and up.
11. Disconnect suction hose (cut off clip) and remove pump.
12. Remove HP union pipe from pump (mark position on
pump).
Installation
1. Install HP union pipe to pump (align correctly), fit new O-ring.
2. Install pump to vehicle connect suction pipe to PAS pump, align timing marks and fit new clip.
3. Manouvre pump into position.
4. Install bolts (x3) PAS pump to engine (torque).
5. Install bolt (x1) HP pump pipe to engine (torque).
6. Connect bottom hose.
7. Clip (x1) harness from cylinder head for access. 8. Install bolt P-clip suction hose to body (torque).
9. Connect HP union to PAS pump pipe, replace O-ring
(torque).
10. Coolant refill (see Workshop Manual procedure 03.03.AD Coolant - Drain & Refill).
11. Install A/C compressor (see Workshop Manual procedure 03.05.BE Compre ssor - Air Conditioning -
Renew).
12. Top-up PAS fluid.
13. Start and run engine, operate steering lock to lock x2.
14. Top-up PAS fluid.
Power Assisted Steering (PAS) Rack -
Remove and Install
Removal
1. Disconnect the battery ground cable.
2. Remove the front undertray (refer to Workshop Manual Procedure 01.02.NB - Front Undertray).
3. Remove the front wheels and tyres (refer to Workshop Manual Procedure 04.04.ED - Wheel and Tyre - Pair).
4. Remove the front right side wheel-arch liner (refer to Workshop Manual Procedure 01.02.GB - Front Right
Side Wheel-Arch Liner).
5. Put a container in position under the oil tank to collect oil.
6. Remove the drain plug from the oil tank.
Figure 1
7. Let the oil drain into the container.
8. Install and tighten the drain plug into the oil tank (refer to Figure 1).
9. Remove the container.
10. Lower the vehicle.
11. Remove the radiator closing panel (refer to Workshop Manual Procedure 01.02.AA - Radiator Closing Panel).
Repair Operation Time (ROT)
Repair Operation Time (ROT)
Repair Operation Time (ROT)
ItemCode
Power Assisted Steering (PAS) Rack -
Remove and Install 11.02.AA