2010 ASTON MARTIN V8 VANTAGE rims

Silencer Assembly (09.01)
Exhaust (09.00)
Issue 5, January 2010 Workshop Manual 9-1-7
11. Position suitable lifter to support weight of silencer.
With assistance, remove silencer.
12. Remove both rear rubber mountings and hanger brackets from silencer.
Installation
1. Clean silencer and mating faces on rear pipes and stub pipes.
2. Install both rear rubber mountings and hanger brackets to silencer.
3. Position silencer on lifter . Install silencer, position
hangers, install and tighten bolts (x4).
4. Install front mountings to silencer, install and tighten bolts (x4).
5. Align silencer to rear pipes. Install springs (x4), and torque tighten bolts (x4).
6. Install and align stub pipes (x2) to silencer and trims in bumper. Align and tighten clamp bolts.
7. Check silencer to rear pipes for correct alignment and clearances.
8. Install stub pipes (x2), insta ll clamps (x2), centralise stub
pipes to exhaust trim finisher, torque tighten clamp nuts
(x2).
9. Check silencer to rear pipes for correct alignment and clearances.
10. Connect lines to both by-pass vacuum valves.
11. Install rear bumper diffuse r. Install and tighten Allen
bolts (x4).
12. Roadster Only - Install RH rear wheel arch liner (refer to
Workshop Manual procedure 01.02.HB Wheel Arch
Liner - Rear - RH - Renew).
13. Roadster Only - Install LH rear wheel arch liner.
14. Coupe Only - Install rear undertray (refer to Workshop
Manual procedure 01.02.PB Undertray - Rear - Renew).
15. Lower vehicle on ramp.
Exhaust Rear Silencer Mounting Rubber-
Renew
Removal
1. Raise vehicle on ramp. 2. Remove Allen bolts (x4), bumper diffuser to mounting
brackets. Remove diffuser, collect mounting brackets.
3. Remove bolts (x2), securing silencer rear hanger brackets to body.
4. Release/remove rubber mounting and hanger bracket from silencer bracket.
5. Remove rubber mounting from hanger bracket.
Installation
1. To aid assembly, apply liquid soap to rubber mounting .
2. Install rubber mounting on hanger bracket.
3. Install rubber mounting on muffler bracket.
4. Align hanger bracket to body, install and torque tighten bolts (x2).
5. Position mounting brackets, install bumper diffuser, install and torque tighten Allen bolts (x4).
6. Lower vehicle on ramp.
Exhaust System-Renew
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove RH exhaust manifold.
4. Remove RH front wheel arch liner (refer to Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
5. Remove LH front wheel arch liner (refer to Workshop
Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
6. Remove heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
7. Loosen EGR pipe in valve.
8. Remove (nuts x2) EGR pipe from manifold, discard
gasket and tie aside.
WA R N I N G
GET THE AID OF ONE MORE PERSON WHEN YOU INSTALL THE REAR EXHAUST SILENCER.
THE SILENCER IS HEAVY .
Ensure correct alignment of exhaust pipes and silencer before tightening of fixing clamps.
Repair Operation Time (ROT)
WA R N I N G
THE EXHAUST SYSTEM WILL BE VERY HOT AFTER
OPERATION. LET THE EXHAUST COOL BEFORE YOU DO WORK. IF YOU DO NO T, PESONAL INJURY CAN
OCCUR.
Repair Operation Time (ROT)

Silencer Assembly (09.01)
Exhaust (09.00)
Issue 5, January 2010 Workshop Manual 9-1-9
20. Coupe Only - Remove cable ties (x2) from LH and RH
HEGO sensor harnesses.
21. Remove nuts (x6), securing each catalyst to exhaust manifolds.
22. With assistance, remove catalysts (x2), release HEGO sensor harnesses from behind heat shield.
23. Coupe Only - Remove string from multiplugs.
24. Discard gaskets (x2) from exhaust manifolds.
25. Coupe Only - Remove bolts (x11), heatshields to centre,
LH and RH rear pipes. Remove heatshields.
Installation
1. Clean heatshields.
2. Coupe Only - Position heatshields to centre, LH and RH
rear pipes. Install and tighten bolts.
3. Install new flange gaskets to exhaust manifolds.
4. With assistance, install both catalysts, install and torque tighten nuts (x6).
5. Roadster Only - Install bolts (x4) and nuts (x2) to
catalyst heatshield.
6. Coupe Only - Feed HEGO sensor harnesses behind
heat shield, secure harnesses with cable ties.
7. Apply exhaust sealant to cent re pipe, install centre pipe
to catalysts and centre mounting. Do not torque clamp
nuts at this stage.
8. Roadster Only - Install centre exhaust mounting bolts
(x4).
9. Apply exhaust sealant to LH and RH rear pipes.
10. Install LH and RH rear pi pes to centre pipe. Do not
torque clamp nuts at this stage.
11. Install both rear rubber mountings and hanger brackets to silencer.
12. Position silencer on lifter . Install silencer, position
hangers, install and tighten bolts (x4).
13. Install front mountings to silencer, install and tighten bolts (x4).
14. Align silencer to rear pipes, install springs (x4) and bolts (x4). Do not torque bolts at this stage.
15. Install and align stub pipes (x2) to silencer and to trims in
bumper.
16. Align clamps, do not torque tighten.
17. Connect lines to both by-pass vacuum valves.
18. Coupe Only - Remove string from multiplugs.
19. Connect multiplugs to HEGO sensors. 20. Working from front to rear, set all exhaust to body
clearances.
21. Tighten all exhaust fixings to the correct torque.
22. Install subframe cross brace, install and torque tighten bolts (x4).
23. Position mounting brackets, install rear bumper diffuser. Install and tighten Allen bolts.
24. Install undertrays - vehicle set (refer to Workshop Manual procedure 01.02.PD Undertrays - Vehicle Set -
Renew).
25. Lower vehicle on ramp.
Attach lengths of string to th e HEGO sensor multiplugs. This
enables routing the HEGO se nsor harness behind the
exhaust heat shield on assembly.
WA R N I N G
GET THE AID OF ONE MORE PERSON WHEN YOU
INSTALL THE REAR EXHAUST SILENCER.
THE SILENCER IS HEAVY .
Ensure correct alignment of exhaust pipes and silencer before tightening of fixing clamps.

Torque Figures
Appendix & Glossary20-1-14 Workshop Manual May 2007
Wheels and Tyre Checks
x x x Check for correct tyre size, type and orientation.
x x x Check and report tyre tread depth.
x x x Check tyres for uneven/excessive wear or damage.
x x x Check/adjust tyre pressures.
x x x Check torque of road wheel nuts.
x x x Check road wheel rims for inner and outer damage.
x x x Check colour coded valve collars for co rrect location (tyre pressure monitoring)
(not Japanese market)
x x x Check ‘Use by ’ date of tyre repair kit and replace if expired or expiry date is
within 12 months
Anti Corrosion Check - x x Check body panels and underbody for corrosion starting from the inside - out
(excluding stone chips).
Final Checks x x x Degrease windscreen.
x x x Check clutch functionality.
x x x Check operation/condition of all seat belts and buckles.
x x x Check that the fuel filler bowl rain drain is clear.
x x x Carry out road test.
1000mls
1500km
3 months10000mls
16000km
12 months20000mls
32000km
24 months