2010 ASTON MARTIN V8 VANTAGE engine oil

Engine Sealing (03.10)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-10-9
8. Install the right exhaust camshaft.
9. Install the five bearing caps in their correct positions.
10. Install the ten bolts and torque tighten them in the sequence specified.
11. Install the Torx bolt that attaches the sprocket to the camshaft.
12. Rotate the camshaft and use feeler gauges to do a check of each valve clearance .
13. Do the procedure again an d install the right intake
camshaft.
14. Remove the Torx bolt that attaches the sprocket.
15. Rotate the right intake and exhaust camshafts until the timing flats on each camshaft face up.
16. Install tool (303-530) onto the right cylinder head to hold the camshafts. Install and tighten the three bolts.
17. Install a new left cylinder he ad gasket. Make sure that it
is correctly engaged on the dowels.
18. With the aid of one more person, install the left cylinder head. Make sure that it is correctly engaged on the
dowels.
19. Install and torque the 12 cylinder head bolts in the correct sequence.
20. Lubricate the left exhaust camshaft journals, camshaft lobes, bearing surfaces on the cylinder head and the
bearing caps with clean engine oil.
21. Install left exhaust camshaft.
22. Install the five bearing caps in their correct positions.
23. Install the ten bolts and torque in the sequence specified.
24. Install the Torx bolt that attaches the sprocket to the left exhaust camshaft.
25. Rotate the left exhaust cam shaft as necessary and use
feeler guages to do a check of each valve clearance.
26. Remove the Torx bolt that attaches the sprocket.
27. Install the left intake camshaft (refer to Workshop Manual procedure 03.09.AV Camshaft - Intake - LH -
Renew).
28. Install the timing chain tensioning tool (303-532) into the right exhaust camshaft sprocket.
29. Apply a force to the tool (303-532) in a counterclockwise direction to hold the sprocket and
torque the right sprocket Torx bolts.
30. Remove the special tool.
31. Connect the electrical conne ctors to the left and right
camshaft timing sensors.
32. Connect the electrical connector to each of the two left and two right knock sensors. 33. Install SAI pump and bracket assembly (refer to
Workshop Manual procedure 03.08.DB Pump and
Bracket Assembly - Secondary Air Injection - Renew).
34. Clean the left exhaust manifold.
35. Install a new gasket for the left exhaust manifold .
36. Install the left exhaust manifold.
37. Install and torque tighten the eight nuts.
38. Install the left front wheel arch liner (refer to Workshop
Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
39. Install the right exhaust manifold (refer to Workshop Manual procedure 09.00.CC Gasket - Exhaust Manifold
- right - Renew).
Right Side Cam Cover - Remove and
Install
Removal
1. Disconnect the battery earth cable.
2. Remove the front crush brace. (Refer to procedure
01.01.LC - Front Crush Brace)
3. Remove the right side fr ont crush bar for the body
reinforcement. (Refer to procedure 01.01.AB - Right
Side Front Crush Bar for the Body Reinforcement)
4. Remove the breather pipe from the cam cover.
5. Install applicable caps to seal the open ports.
6. Remove the ignition coil cover.
7. Disconnect the electrical connector from each of the four ignition coils.
8. Disconnect the electrical connector from the Variable Valve Timing (VVT) solenoid.
9. Release the fir tree clip that attaches the wiring harness for the ignition coils.
10. Move the wiring harness for the ignition coils away.
11. Release the wiring harness for the injectors from the mounts.
12. Cut and remove the three cable ties that attach the rear of the wiring harness for the injectors.
13. Remove the screw that attaches the purge pipe P-clip to the cam cover.
14. Move the purge-pipe P-clip away.
15. Release the purge pipe and heater pipe from the two clips on the wiring harness bracket.
16. Remove the two nuts and two screws that attach the front bracket for the wiring harness.
17. Remove the three screws that attach the rear bracket for
the wiring harness.
18. Remove the rear bracket for the wiring harness.
19. Remove the front bracket for the wiring harness.
WA R N I N G
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Caution
Gradually tighten one bolt and then the next to correctly
install the camshaft bearing ca ps in the step that follows.
Repair Operation Time (ROT)

Engine Sealing (03.10)
Engine (03.00)3-10-10 Workshop Manual Issue 5, Janauary 2010
20. Remove the four screws that attach each ignition coil.
21. Remove the four ignition coils.
22. Remove the 14 screws that attach the cam cover to the engine.
23. Remove and discard the seals for the 14 cam cover screws.
24. Remove the cam cover.
25. Remove and discard the O-ring seal for the VVT solenoid.
26. Remove and discard the cam cover gasket.
27. Remove and discard the four O-ring seals from the spark plug wells.
28. Clean the component mating faces.
Install
1. Install four new O-ring seals in the spark plug wells.
2. Install a new O-ring seal for the VVT solenoid.
3. Install a new cam cover gasket.
4. Apply a 12 mm by 3 mm bead of sealant to the tri-joints shown.
Figure C03-10-101
5. Install the cam cover.
6. Install new seals for the 14 cam cover screws. 7. Install and torque the 14 screws that attach the cam
cover to the engine in the sequence shown to 10 Nm.
8. Install the four ignition coils.
9. Install and torque the screw that attaches each of the four ignition coils to 5 Nm.
10. Install the front bracket for the wiring harness.
11. Install the rear bracket for the wiring harness.
12. Install and torque the three screws that attach the rear bracket for the wiring harness to 11 Nm.
13. Install and tighten the two nuts and three screws that attach the front bracket for the wiring harness.
14. Install the purge pipe and he ater pipe into the two clips
on the wiring harness bracket.
15. Put the purge pipe P-clip into the correct position.
16. Install and tighten the screw that attaches the purge pipe P-clip to the cam cover.
17. Use three applicable cable ties to attach the rear of the wiring harness to the front bracket.
18. Install the wiring harness for the injectors into the mounts.
19. Install the fir tree clip that attaches the wiring harness for the ignition coils.
20. Connect the electrical conne ctors to each of the four
ignition coils.
21. Connect the electrical connector to the VVT solenoid.
22. Install the ignition coil cover.
23. Remove and discard the caps from the breather pipes.
24. Install the breather pipes to the cam cover.
25. Install the right side front crush bar for the body reinforcement. (0101AB - Righ t Side Front Crush Bar for
the Body Reinforcement)
26. Install the front crush brace. (0101LC - Front Crush Brace)
Note: When you remo ve the cam cover
attachment screws in th e step that follows,
record their installed positions in the cam
cover.
CAUTION
Tighten the screws gradually and equally in the step
that follows. If you do not, the cam cover gasket can be
damaged.
C03-10-101
Repair Operation Time (ROT)
ItemCode
Cam Cover - Vehicle Set - Remove
and Install 03.10.AW

Engine Sealing (03.10)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-10-11
Removal
1. Remove the left side cam cover (Refer to ’Left Side Cam Cover - Remove and Install’, page 3-10-4).
2. Remove the right side cam cover (Refer to ’Right Side Cam Cover - Remove and Install’, page 3-10-9).
Install
1. Install the left side cam cover (Refer to ’Left Side Cam Cover - Remove and Install’, page 3-10-4).
2. Install the right side cam cover (Refer to ’Right Side Cam Cover - Remove and Install’, page 3-10-9).
Engine Timing Cover-Renew (with Engine
Removed
)
Removal
1. Remove the engine assembly (refer Workshop Manual procedure 03.00.AA Engi ne Assembly - Renew).
2. Position drain container.
3. Remove the drain plug and drain the oil from the sump.
4. Remove the left cam cover (Refer to ’Left Side Cam Cover - Remove and Install’, page 3-10-4).
5. Remove the right cam cover (Refer to ’Right Side Cam Cover - Remove and Install’, page 3-10-9).
6. Release the hose clips and disconnect the two coolant hoses from the coolant manifold.
7. Release the hose clip and di sconnect the hose from the
oil separator.
8. Remove the four Torx bolts that attach the coolant manifold to cylinder heads (refer to Figure 1).
Figure 1
9. Release the coolant mani fold from coolant pipe,
disconnect the temperature sensor multiplug.
10. Remove the coolant manifold.
11. Remove and discard the two O-rings from the coolant manifold. 12. Loosen the three water pump pulley bolts (refer to
Figure 2).
Figure 2
13. Use an applicable socket bar to release the auxiliary
drive belt tensioner.
14. Remove the drive belt.
15. Remove the three bolts and remove the water pump pulley.
16. Remove the bolt that attaches the auxiliary drive belt tensioner.
17. Remove the tensioner (refer to Figure 3).
Figure 3
18. Remove the two bolts that attach the inspection cover to the lower crankcase. Remove the cover.
19. Install tool (303-1185) to hold flywheel. Install and tighten the two bolts .
20. Install the thrust button of tool (303 -1186) into the crankshaft.
21. Put the tool in position in the pulley. Attach the tool with the two bolts. Tighten the centre bolt and remove
the pulley from the crankshaft.
22. Collect the crankshaft pulley, locking ring and the special tool thrust button.
23. Remove the special tool from the pulley.
24. Remove and discard the O-ring seal from pulley.
25. Remove the bolt that attaches the alternator idler pulley.
Repair Operation Time (ROT)
A030368
A030553A
A030553

Engine Sealing (03.10)
Engine (03.00)3-10-12 Workshop Manual Issue 5, Janauary 2010
26. Remove the pulley (refer to Figure 4).
Figure 4
27. Remove the bolt that attaches the A/C compressor idler pulley. Remove the pulley (refer to Figure 5).
Figure 5
28. Position the drain tray.
29. Remove the oil filter.
30. Release the oil separator drain tube from the timing cover (refer to Figure 6).
Figure 6
31. Release the clip for the oil separator drain tube from the bracket. 32. Release the terminal cover on the alternator. Remove
the nut that attaches the battery cable to the alternator.
(refer to Figure 7).
Figure 7
33. Disconnect the electrical connector from the alternator.
34. Remove the bolt and the nut and bolt that attach the alternator.
35. Remove the alternator.
36. Remove the three Torx bolts that attach the alternator mounting bracket to cylinder block. Remove the bracket
(refer to Figure 8).
Figure 8
37. Remove the three bolts that attach the PAS pump to mounting bracket. Move the pump away.
A030553B
A030553C
A030582
A0310242

Engine Sealing (03.10)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-10-13
38. Remove the four Torx bolts that attach the PAS pump mounting bracket to the cylinder block. Remove the
bracket (refer to Figure 9).
Figure 9
39. Remove the 27 bolts that attach the timing cover to the engine. Collect the bracet for the oil separator drain
tube. Remove the timing cover.
40. Remove the outer and inner rubber seals from the timing cover (refer to Figure0).
Figure0
41. Remove the front crankshaft oil seal from timing cover.
Installation
1. Clean the timing cover and mating face on engine.
2. Install the inner and outer seals into timing cover.
3. Apply 3mm x 12mm beads of sealant to the eight joints
on the engine.
4. Install the timing cover. Put the oil separator drain tube bracket in position. Install the 27 bolts and torque the
bolts in the specified sequence. 5. Using tool (303-750), instal
l front crankshaft oil seal.
Remove special tool and seal protector.
6. Clean crankshaft pulley and mating face on crankshaft.
7. Lubricate and install new O-ring seal in crankshaft pulley.
8. Install crankshaft pulley, locking ring and new pulley bolt.
9. Torque tighten crankshaft pulley bolt. Remove special tool (303-1185) from crankcase.
10. Install inspection cover to lower crankcase, install and tighten bolts (x2).
11. Install PAS pump mounting bracket, install and torque tighten Torx bolts (x4).
12. Install PAS pump, install and torque tighten bolts (x3).
13. Install alternator mounting bracket, install and torque tighten Torx bolts (x3).
14. Install alternator, install bolt and nut/bolt and torque tighten
15. Connect battery cable, install and torque tighten nut, secure cover. Connect multiplug.
16. Lubricate seal, install new oil filter.
17. Install oil separator drai n tube clip in bracket.
18. Install oil separator drain tube to timing cover.
19. Install A/C compressor idler pulley, torque tighten bolt.
20. Install alternator idler pulley, torque tighten bolt.
21. Install auxiliary drive belt te nsioner, torque tighten bolt.
22. Install water pump pulley, install bolts (x3).
23. Using a suitable socket ba r, release auxiliary drive belt
tensioner, install drive belt.
24. Torque tighten water pump pulley bolts (x3).
25. Clean coolant manifold and mating faces on cylinder heads.
26. Install new O-ring seals (x2) to coolant manifold.
27. Position coolant manifold, connect temperature sensor
multiplug, install coolant pipe in manifold.
28. Install and torque tighten Torx bolts (x4) that attach the coolant manifold to cylinder heads.
29. Connect coolant hoses (x3) to coolant manifold and
secure clips.
30. Connect engine breather to oil separator.
31. Clean left and right cam covers.
32. Install the right cam cover (Refer to ’Right Side Cam Cover - Remove and Install’, page 3-10-9).
33. Install left cam cover (Refer to ’Left Side Cam Cover -
Remove and Install’, page 3-10-4).
34. Install the engine assembly (refer to Workshop Manual procedure 03.00.AA Engine Assembly - Renew).
Caution
Make sure the cranks haft front oil seal mating faces are
clean and dry.
Caution
Do not remove the crankshaft front oil seal protector
until the oil seal is correctly installed.
If you do, the oil seal can be damaged.
A0310243
A0310245
Caution
The bolt thread in the cran kshaft must be cleaned out
before a new crankshaft pulley retaining bolt is installed.
Note: Check the crankshaft pulley and locking ring for damage.

Engine Sealing (03.10)
Engine (03.00)3-10-14 Workshop Manual Issue 5, Janauary 2010
John Guest Cartridge in the Engine
Timing Cover - Repair
Removal
1. Open the bonnet.
2. Raise the vehicle and make it safe.
3. On Roadster models, remove the front undertray (Refer
to ’Centre Undertray - Remove and Install (Roadster
Only)’, page 1-2-1).
4. Put an approved container under the front cover to collect oil.
5. Disconnect the oil drain pipe from the John Guest
cartridge.
6. Let the oil drain.
7. Use a trim tool as a lever to remove the plastic collet from the cartridge.
8. Remove and discard the O-ring from the cartridge.
9. Clean all unwanted oil from the cartridge.
Install
1. Apply a layer of oil to the new O-ring .
2. Carefully install the new O- ring in the cartridge. Make
sure that the O-ring is in the correct position against the
shoulder of the cartridge.
3. Install the new plastic collet into the cartridge.
4. Connect the oil pipe into the cartridge.
5. Clean all unwanted oil from the area around the cartridge.
6. Remove the container of drained oil.
7. On Roadster models, install the front undertray (Refer to ’Centre Undertray - Remove and Install (Roadster
Only)’, page 1-2-1).
8. Lower the vehicle.
9. Remove the cap from the oil tank.
10. Add oil to the oil tank to the correct level.
11. Install the cap on the oil tank.
12. Start and operate the engine for approximately five minutes.
13. Stop the engine.
14. Wait five minutes for the oil to drain back to the sump.
15. Do a check of the oil le vel. Add oil if necessary. 16. Install the oil tank cap.
17. Close the bonnet.
Repair Operation Time (ROT)

Power Conversion (03.11)
Engine (03.00)
May 2007 Workshop Manual 3-11-1
Engine (03.00)
Power Conversion (03.11)
Maintenance
Connecting Rod Bearing-Renew (Engine
Set)
Removal
1. Remove engine oil sump (see Workshop Manual
procedure 03.02.BN Pan - Oil Sump - Remove and Re-
seal).
2. Remove spark plugs (see Workshop Manual procedure 03.07.DB Spark Plugs - Engine Set - Renew).
3. Remove bolts (x8) securing windage tray to engine bedplate, remove windage tray.
4. Mark bearing caps and connecting rods for correct installation.
5. Rotate crankshaft clockwise to access number 1 cylinder connecting rod bolts.
6. Remove bolts securing bearing cap to connecting rod, remove bearing cap (see Figure 1).
Figure 1
7. Install special tools (303-535) to the connecting rod to prevent damage to crankshaft journal.
8. Move connecting rod upwards, remove bearing shell.
9. Record colour code on bearing shell edge. 10. Remove and discard bearing shell from cap.
11. Record colour code on bearing shell edge, discard
bearing shell.
12. Wipe crankshaft journal, connecting rod and bearing cap using a lint free cloth.
13. Inspect crankshaft journal for damage.
14. Check crankshaft journal for ovality using a micrometer and record journal diameters.
Installation
1. Select the correct colour coded bearing shells for each connecting rod crankshaft journal.
2. Install new selective bearing shell in connecting rod.
3. Lubricate crankshaft journal with clean engine oil.
4. Install connecting rod on crankshaft journal.
5. Remove special tools (303-535) from connecting rod.
6. Install new selective bearing shell in bearing cap.
7. Install bearing cap and new bolts (x2), torque tighten bearing cap bolts.
8. Repeat procedure for remaining connecting rod bearings.
9. Install windage tray to engine bedplate, install and torque tighten bolts (x8).
10. Install spark plugs (see Workshop Manual procedure 03.07.DB Spark Plugs - Engine Set - Renew).
11. Install engine oil sump (see Workshop Manual
procedure 03.02.BN Pan - Oil Sump - Remove and re-
seal).
Crankshaft Main Bearing-Renew (Engine
Set)
Removal
1. Remove bolts (x2), inspection cover to lower crankcase, remove cover.
2. Install tool (303-1185) to restrain flywheel, install and tighten bolts (x2).
3. Remove bolts (x6), clutch cover to flywheel.
4. Release clutch cover from dowels (x3), remove clutch cover, collect drive plate.
5. Remove and discard bolts (x8), flywheel to crankshaft flange.
6. Remove bolts (x2), collect tool (303-1185).
Repair Operation Time (ROT)
WA R N I N G
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Caution
Pistons, connecting rods an d connecting rod bearings
should be numbered to make sure they are reassembled
in the same position.
Caution
Connecting rod bolts are tor qu
e tightened to yield and
mu st be replaced.
A0311314
Note: Connecting rod bearings ar e a selective fit by colour
code on edge of bearing shell.
Caution
When assembling connecting rods and connecting rod
bearing caps it is imperative that bearing slots and tangs
be located on the same side of the connecting rods.
Repair Operation Time (ROT)

Power Conversion (03.11)
Engine (03.00)3-11-2 Workshop Manual May 2007
7. Release flywheel from dowel, remove flywheel.
8 . R e m o v e e n g i n e s u m p ( s e e Wo r k s h o p M a n u a l p ro c e d u r e
03.02.CN Pan - Oil Sump - Remove and re-seal With
Engine Removed).
9. Remove bolts (x8) securing windage tray to engine bedplate, remove windage tray.
10. Mark bearing caps and connecting rods for correct installation (see Figure 1).
Figure 1
11. Rotate crankshaft clockwise to access number 1 cylinder
connecting rod bolts.
12. Remove and discard bolts (x16) securing bearing caps to connecting rods, remove bearing caps (see Figure 2).
Figure 2
13. Install special tools (303-535) to the connecting rod to prevent damage to crankshaft journal.
14. Carefully push each connecting rod/piston assembly up each cylinder bore.
15. Secure Dial Test Indicator (DTI) on engine bedplate.
16. Push crankshaft fully rearwards. 17. Position DTI probe on cran
kshaft web and zero gauge.
18. Push crankshaft fully forw ards and record reading on
dial gauge.
19. Remove DTI gauge.
20. Noting their fitted positions, remove bolts (x34) securing engine bedplate to cylinder block (see Figure 3).
Figure 3
21. Carefully release and remove engine bedplate from cylinder block (see Figure 4).
Figure 4
22. Carefully remove crankshaft from cylinder block.
23. Remove rear oil seal from crankshaft.
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN.
USED ENGINE OIL CAN BE HARMFUL.
Caution
Connecting rod bolts are tor que tightened to yield and
must be replaced.
A0311329
A0311314
A0311329
A0311329