2010 Alfa Romeo Giulietta service

172
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
❍inflate the tyre to the pressure shown in the “Wheels” para-
graph in the “Technical Specifications” chapter. In order to ob-
tain a precise reading, check the pressure on pressure gauge
B-fig. 126 with the compressor off;
❍if after 5 minutes you cannot reach at least 1.8 bar, unplug the
compressor from the valve and the socket, then move the car
forward about ten metres in order to distribute the sealant in-
side the tyre evenly, then repeat the inflation operation;
❍if you still cannot obtain a pressure of at least 1.8 bar within
5 minutes from the compressor switching on, do not drive off
and contact Alfa Romeo Authorized Services;
❍after driving for about 10 minutes, stop and check the tyre pres-
sure again; remember to put the handbrake on;
Apply the adhesive label where it can be easily
seen by the driver as a reminder that the tyre has
been treated with the quick repair kit. Drive care-
fully, particularly on bends. Do not exceed 80 km/h. Do
not accelerate or brake suddenly.
❍if a pressure value of at least 1.8 bar is detected, restore the
correct pressure (with the engine running and the handbrake
engaged), and drive with care to Alfa Romeo Authorized Ser-
vices.
If the pressure has fallen below 1.8 bar, do not dri-
ve any further: the Automatic Fix&Go quick tyre
repair kit cannot guarantee proper hold because
the tyre is too damaged. Contact Alfa Romeo Authorized
Services.
Remember to inform the workshop that the tyre
has been treated with a quick repair kit. Give the
instruction booklet to the personnel charged with
handling the treated tyre.
fig. 127A0K0128m
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 172

174
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Halogen bulbs must be handled holding the metal-
lic part only. Touching the transparent part of the
bulb with your fingers may reduce the intensity
of the light emitted and even compromise the longevity
of the bulb itself. In the event of accidental contact, wipe
the bulb with an alcohol-soaked cloth and leave to dry.
Modifications or repairs to the electrical system
(electronic control units) that are not carried out
properly or do not take the technical specifications
of the system into account can cause malfunctions lead-
ing to the risk of fire.
Halogen bulbs contain pressurised gas which may
cause small fragments of glass to be projected out-
wards if the bulb is broken.
Due to the high power supply voltage, gas dis-
charge bulbs (Bi-Xenon) should only be replaced
by specialised personnel: danger of death! Contact
Alfa Romeo Authorized Services.
IMPORTANT When the weather is cold or damp or after heavy rain
or after washing, the surface of headlights or rear lights, may steam
up and/or form drops of condensation on the inside. This is a nat-
ural phenomenon due to the difference in temperature and humidity
between the inside and the outside of the glass which does not
indicate a fault and does not compromise the normal operation of
lighting devices. The mist disappears quickly turning the lights on,
starting from the centre of the diffuser, extending progressively
towards the edges.
CHANGING A BULB
GENERAL INSTRUCTIONS
❍Before changing a bulb check the contacts for oxidation;
❍blown bulbs must be replaced with others of the same type
and power:
❍after replacing a headlight bulb, always check its alignment;
❍when a light is not working, check that the corresponding fuse
is intact before changing the bulb. For the location of fuses, re-
fer to the “Changing a fuse” paragraph in this section.
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 174

177
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
CHANGING AN EXTERIOR BULB
FRONT LIGHT CLUSTERS fig. 131
These contain the bulbs for the side lights/day lights (DRL), dipped
beams, main beams and direction indicators. The bulbs are arranged
as follows:
A.Side lights/day lights and main beam headlights;
B.Dipped beam headlights;
C.Direction indicators.
SIDE LIGHTS/DAY LIGHTS (DRL)
These are LEDs. Contact Alfa Romeo Authorized Services to replace
these lights.
MAIN BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❍remove cover A-fig. 131;
❍remove the connector A-fig. 132 and then open the tabs B to-
wards;
❍extract the bulb C and replace it;
❍refit the new lamp, making sure that it is locked correctly, and
secure the tabs B again and reconnect the connector A;
❍finally refit the cover A-fig. 131.
fig. 131A0K0201mfig. 132A0K0202m
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 177

178
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❍remove cover B-fig. 131;
❍remove the connector A-fig. 133, press the tab B forward and
then release by pushing it towards the inside the car;
❍extract the bulb C and replace it;
❍refit the new lamp, making sure that it is locked correctly, and
secure the tab B again and reconnect the connector A;
❍finally refit cover B-fig. 131.
DIRECTION INDICATORS
Front
To replace the bulb, turn the cover C-fig. 131 anticlockwise by ¼
of a turn and replace the bulb + bulb holder assembly A-fig. 134.
Side
These are LEDs. Contact Alfa Romeo Authorized Services to replace
these lights.
FRONT FOG LIGHTS
(for versions/markets, where provided)
Contact Alfa Romeo Authorized Services to replace these bulbs.
fig. 133A0K0203mfig. 134A0K0204m
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 178

179
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
REAR LIGHT CLUSTERS
These contain the taillights, brake lights, direction indicators (bulbs
in fixed light cluster), reverse light and rear fog light (bulb in light
cluster on boot hatch).
Removing the fixed light cluster
Proceed as follows:
❍open the boot and loosen the rear light cluster fastening screw
A-fig. 135;
❍extract the light cluster by removing it with both hands in the
direction of the arrow (see fig. 135);
❍connect the electrical connector and replace the bulb concerned.
TAILLIGHTS/BRAKE LIGHTS
These are LEDs. Contact Alfa Romeo Authorized Services to replace
these lights.
DIRECTION INDICATORS
With the light cluster removed, to replace the bulb undo the two
screws A-fig. 136, remove the bulb holder and replace bulb B.
fig. 135A0K0184mfig. 136A0K0205m
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 179

181
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
THIRD BRAKE LIGHTS
These are LEDs and are located on the spoiler integrated on the
boot hatch. Contact Alfa Romeo Authorized Services to replace these
lights.
NUMBER PLATE LIGHTS
To change the bulb proceed as follows:
❍remove the lens unit A-fig. 139;
❍turn bulb holder B-fig. 140 anticlockwise, remove bulb C and
replace it.
fig. 139A0K0147mfig. 140A0K0146m
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 181

184
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
GLOVE COMPARTMENT LIGHT
To change the bulb, proceed as follows:
❍open the glove compartment and extract the light A-fig. 147;
❍open the protection B and replace the bulb;
❍re-close the protective cover B on the lens;
❍refit the light A by inserting it in its correct position firstly on
one side and then on the other until it clicks into place.
fig. 147A0K0172m
COURTESY LIGHT
(for versions/markets, where provided)
For the replacement of these bulbs, contact Alfa Romeo Authorized
Services.
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 184

187
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Contact Alfa Romeo Authorized Services should the
fuse blow again.
Never replace a blown fuse with metallic wires or
other material.
Never replace a fuse with another of higher am-
perage: FIRE RISK.
If a general protection fuse (MEGA-FUSE, MIDI-
FUSE, MAXI-FUSE) blows, contact Alfa Romeo
Authorized Services.
Remove the key from the ignition switch and switch
off all loads before replacing a fuse.
Contact Alfa Romeo Authorized Services if a safe-
ty system (air bags, brakes), engine system (en-
gine, gearbox) or steering system general pro-
tection fuse blows.
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 187